The default protection for the BLE ringbuf is to use
MICROPY_BEGIN_ATOMIC_SECTION, which disables all interrupts. On stm32 it
only needs to disable the lowest priority IRQ, pendsv, because that's the
IRQ level at which the BLE stack is driven.
qstrs in this file are always included in all builds, even if not used
anywhere. So remove those that are never needed, and make USB names
conditional on having USB enabled.
And return -MP_EIO if calling storage_read_block/storage_write_block fails.
This lines up with the return type and value (negative for error) of the
calls to MICROPY_HW_BDEV_READBLOCKS (and WRITEBLOCKS, and BDEV2 versions).
The pyb.Flash() class can now be used to construct objects which reference
sections of the flash storage, starting at a certain offset and going for a
certain length. Such objects also support the extended block protocol.
The signature for the constructor is: pyb.Flash(start=-1, len=-1).
This commit refactors and generalises the boot-mount routine on stm32 so
that it can mount filesystems of arbitrary type. That is, it no longer
assumes that the filesystem is FAT. It does this by using mp_vfs_mount()
which does auto-detection of the filesystem type.
Using mp_hal_delay_ms allows the scheduler to run, which might result in
another transmit operation happening, which would bypass the sleep (and
fail). Use mp_hal_delay_us instead.
The compile-time configuration value MICROPY_HW_RTC_USER_MEM_MAX can now be
used to define the amount of memory set aside for RTC.memory(). If this
value is configured to zero then the RTC.memory functionality is not
included in the build.
The IDF heap is more fragmented with IDF 4 and mbedtls cannot allocate
enough RAM with 16+16kiB for both in and out buffers, so reduce output
buffer size.
Fixes issue #5303.
This commit removes the Makefile-level MICROPY_FATFS config and moves the
MICROPY_VFS_FAT config to the Makefile level to replace it. It also moves
the include of the oofatfs source files in the build from each port to a
central place in extmod/extmod.mk.
For a port to enabled VFS FAT support it should now set MICROPY_VFS_FAT=1
at the level of the Makefile. This will include the relevant oofatfs files
in the build and set MICROPY_VFS_FAT=1 at the C (preprocessor) level.
This commit adds support for littlefs (v2) on all esp32 boards.
The original FAT filesystem still works and any board with a preexisting
FAT filesystem will still work as normal. It's possible to switch to
littlefs by reformatting the block device using:
import uos, flashbdev
uos.VfsLfs2.mkfs(flashbdev.bdev)
Then when the board reboots (soft or hard) the new littlefs filesystem will
be mounted. It's possible to switch back to a FAT filesystem by formatting
with uos.VfsFat.mkfs(flashbdev.bdev).
This commit adds an implementation of machine.Timer backed by the soft
timer mechanism. It allows an arbitrary number of timers with 1ms
resolution, with an associated Python callback. The Python-level API
matches existing ports that have a soft timer, and is used as:
from machine import Timer
t = Timer(freq=10, callback=lambda t:print(t))
...
t = Timer(mode=Timer.ONE_SHOT, period=2000, callback=lambda t:print(t))
...
t.deinit()
This commit adds an implementation of a "software timer" with a 1ms
resolution, using SysTick. It allows unlimited number of concurrent
timers (limited only by memory needed for each timer entry). They can be
one-shot or periodic, and associated with a Python callback.
There is a very small overhead added to the SysTick IRQ, which could be
further optimised in the future, eg by patching SysTick_Handler code
dynamically.
The MP_STATE_THREAD(stack_top) is always available so use it instead of
creating a separate variable. This also allows gc_collect() to be used as
an independent function, without real_main() being called.
When a SPI bus is initialized with a SPI host that is currently in use the
exception msg incorrectly indicates "SPI device already in use". The
mention of "device" in the exception msg is confusing because the error is
about trying to use a SPI host that is already claimed. A better exception
msg is "SPI host already in use".
For consistency with "umachine". Now that weak links are enabled
by default for built-in modules, this should be a no-op, but allows
extension of the bluetooth module by user code.
Also move registration of ubluetooth to objmodule rather than
port-specific.
This commit implements automatic module weak links for all built-in
modules, by searching for "ufoo" in the built-in module list if "foo"
cannot be found. This means that all modules named "ufoo" are always
available as "foo". Also, a port can no longer add any other weak links,
which makes strict the definition of a weak link.
It saves some code size (about 100-200 bytes) on ports that previously had
lots of weak links.
Some changes from the previous behaviour:
- It doesn't intern the non-u module names (eg "foo" is not interned),
which saves code size, but will mean that "import foo" creates a new qstr
(namely "foo") in RAM (unless the importing module is frozen).
- help('modules') no longer lists non-u module names, only the u-variants;
this reduces duplication in the help listing.
Weak links are effectively the same as having a set of symbolic links on
the filesystem that is searched last. So an "import foo" will search
built-in modules first, then all paths in sys.path, then weak links last,
importing "ufoo" if it exists. Thus a file called "foo.py" somewhere in
sys.path will still have precedence over the weak link of "foo" to "ufoo".
See issues: #1740, #4449, #5229, #5241.
When loading a manifest file, e.g. by include(), it will chdir first to the
directory of that manifest. This means that all file operations within a
manifest are relative to that manifest's location.
As a consequence of this, additional environment variables are needed to
find absolute paths, so the following are added: $(MPY_LIB_DIR),
$(PORT_DIR), $(BOARD_DIR). And rename $(MPY) to $(MPY_DIR) to be
consistent.
Existing manifests are updated to match.
Prior to this commit the systick IRQ priority was set at lowest priority on
F0/L0/WB MCUs, because it was left at the default and never configured.
This commit ensures the priority is configured and sets it to the highest
priority.
Remove the 240MHz CPU config option from sdkconfig.base and create a new
sdkconfig.240mhz file for those boards that want to use 240MHz on boot.
The default CPU frequency is now 160MHz (was 240MHz), to align with the ESP
IDF and support more boards (eg those with D2WD chips).
Fixes issue #5169.
This prevents issues with concurrent access to the ringbuf.
MICROPY_BEGIN_ATOMIC_SECTION is only atomic to the same core. We could
address this with a mutex, but it's also not safe to call mp_sched_schedule
across cores.
This avoids a confusing ENOMEM raised from gap_advertise if there is
currently an active connection. This refers to the static connection
buffer pre-allocated by Nimble (nothing to do with MicroPython heap
memory).
This patch add basic building blocks for nrf9P60.
It also includes a secure bootloader which forwards all
possible peripherals that are user selectable to become
non-secure. After configuring Flash, RAM and peripherals
the secure bootloader will jump to the non-secure domain
where MicroPython is placed.
The minimum size of a secure boot has to be a flash
block of 32Kb, hence why the linker scripts are
offsetting the main application this much.
The RAM offset is set to 128K, to allow for later
integration of Nordic Semiconductor's BSD socket
library which reserves the range 0x20010000 - 0x2001FFFF.
Add support for pca10059 with REPL over tinyusb USB CDC.
The board also includes a board specific module that will
recover UICR->REGOUT0 in case this has been erased.
This initial support does not preserve any existing bootloader
on the pca10090 in case this was present, and expects to use all
available flash on the device.
Add nrf-port finyusb driver files. USB CDC can be activated
by board configuration files using the MICROPY_HW_USB_CDC.
Updating BLE driver, Makefile, nrfx-glue and main.c to plug
in the tinyusb stack.
The specific board can be selected with the BOARD makefile variable. This
defaults (if not specified) to BOARD=GENERIC, which is the original default
firmware build. For the 512k target use BOARD=GENERIC_512K.
On other ports (e.g. ESP32) they provide a complete Nimble implementation
(i.e. we don't need to use the code in extmod/nimble). This change
extracts out the bits that we don't need to use in other ports:
- malloc/free/realloc for Nimble memory.
- pendsv poll handler
- depowering the cywbt
Also cleans up the root pointer management.
STM32F0 has PCLK=48MHz and maximum ADC clock is 14MHz so use PCLK/4=12MHz
to stay within spec of the ADC peripheral. In pyb.ADC set common sampling
time to approx 4uS for internal and external sources. In machine.ADC
reduce sample time to approx 1uS for external source, leave internal at
maximum sampling time.
This commit adds the option to use HSE or MSI system clock, and LSE or LSI
RTC clock, on L4 MCUs.
Note that prior to this commit the default clocks on an L4 part were MSI
and LSE. The defaults are now MSI and LSI.
In mpconfigboard.h select the clock source via:
#define MICROPY_HW_RTC_USE_LSE (0) or (1)
#define MICROPY_HW_CLK_USE_HSE (0) or (1)
and the PLLSAI1 N,P,Q,R settings:
#define MICROPY_HW_CLK_PLLSAIN (12)
#define MICROPY_HW_CLK_PLLSAIP (RCC_PLLP_DIV7)
#define MICROPY_HW_CLK_PLLSAIQ (RCC_PLLQ_DIV2)
#define MICROPY_HW_CLK_PLLSAIR (RCC_PLLR_DIV2)
The the nrfx driver is aware of chip specific registers, while
the raw HAL abstraction is not. This driver enables use of NVMC
in non-secure domain for nrf9160.
This patch moves the check for MICROPY_PY_MACHINE_TEMP to come
before the inclusion of nrf_temp.h. The nrf_temp.h depends on
the NRF_TEMP_Type which might not be defined for all nRF devices.
For use with F0 MCUs that don't have HSI48. Select the clock source
explicitly in mpconfigboard.h.
On the NUCLEO_F091RC board use HSE bypass when HSE is chosen because the
NUCLEO clock source is STLINK not a crystal.
Before this patch the UART baudrate on F0 MCUs was wrong because the
stm32lib SystemCoreClockUpdate sets SystemCoreClock to 8MHz instead of
48MHz if HSI48 is routed directly to SYSCLK.
The workaround is to use HSI48 -> PREDIV (/2) -> PLL (*2) -> SYSCLK.
Fixes issue #5049.
Enabled by default, but disabled when REPL is connected to the VCP (this is
the existing behaviour). Can be configured at run-time with, eg:
pyb.USB_VCP().init(flow=pyb.USB_VCP.RTS | pyb.USB_VCP.CTS)
The new fdcan.c file provides the low-level C interface to the FDCAN
peripheral, and pyb_can.c is updated to support both traditional CAN and
FDCAN, depending on the MCU being compiled for.
Add the project file to the mpy-cross directory, which is also where the
executable ends up, and change the Appveyor settings to build mpy-cross
with both msvc and mingw-w64 and verify this all works by running tests
with --via-mpy.
If this is not set it might default to calls to open() to use text mode
which is usually not wanted, and even wrong and leading to incorrect
results when loading binary .mpy files.
This also means that text files written and read will not have line-ending
translation from \n to \r\n and vice-versa anymore. This shouldn't be much
of a problem though since most tools dealing with text files adapt
automatically to any of the 2 formats.
Reserve sources.props for listing just the MicroPython core and extmod
files, similar to how py.mk lists port-independent source files. This
allows reusing the source list, for instance for building mpy-cross. The
sources for building the executable itself are listed in the corresponding
project file, similar to how the other ports specify the source files in
their Makefile.
Append to PyIncDirs, used to define include directories specific to
MicroPython, instead of just overwriting it so project files importing this
file can define additional directories. And allow defining the target
directory for the executable instead of hardcoding it to the windows
directory. Main reason for this change is that it will allow building
mpy-cross with msvc.
We want the .vcxproj to be just a container with the minimum content for
making it work as a project file for Visual Studio and MSBuild, whereas the
actual build options and actions get placed in separate reusable files.
This was roughly the case already except some compiler options were
overlooked; fix this here: we'll need those common options when adding a
project file for building mpy-cross.
These were probably added to detect more qstrs but as long as the
micropython executable itself doesn't use the same build options the qstrs
would be unused anyway. Furthermore these definitions are for internal use
and get enabled when corresponding MICROPY_EMIT_XXX are defined, in which
case the compiler would warn about symbol redefinitions since they'd be
defined both here and in the source.
This commit adds support for a second supported hash (currently set to the
4.0-beta1 tag). When this hash is detected, the relevant changes are
applied.
This allows to start using v4 features (e.g. BLE with Nimble), and also
start doing testing, while still supporting the original, stable, v3.3 IDF.
Note: this feature is experimental, not well tested, and network.LAN and
network.PPP are currently unsupported.
This option affects py/vm.c and py/gc.c and using -Os gets them compiling a
bit smaller, and small firmware is the aim of these two ports. Also,
having these files compiled with -Os on these ports, and -O3 as the default
on other ports, gives a better understanding of code-size changes when
making changes to these files.
According to the schematic, the SDRAM part on this board is a
MT48LC4M32B2B5-6A, with "Row addressing 4K A[11:0]" (per datasheet). This
commit updates mpconfigboard.h from 13 to 12 to match.
This patch uses the newly-added esp32.Partition class to replace the
existing FlashBdev class. Partition objects implement the block protocol
so can be directly mounted via uos.mount(). This has the following
benefits:
- allows the filesystem partition location and size to be specified in
partitions.csv, and overridden by a particular board
- very easily allows to have multiple filesystems by simply adding extra
entries to partitions.csv
- improves efficiency/speed of filesystem operations because the block
device is implemented fully in C
- opens the possibility to have encrypted flash storage (since Partitions
can be encrypted)
Note that this patch is fully backwards compatible: existing filesystems
remain untouched and work with this new code.
- STM32F407VGT6 (1MB of Flash, 192+4 Kbytes of SRAM)
- 5V (via USB) or Li-Polymer Battery (3.7V) power input
- 2 x LEDs
- 2 x user switches
- 2 x mikroBUS sockets
- 2 x 1x26 mikromedia-compatible headers (52 pins)
https://www.mikroe.com/clicker-2-stm32f4
Mboot currently requires at least three LEDs to display each of the four
states. However, since there are only four possible states, the states can
be displayed via binary counting on only 2 LEDs (if only 2 are available).
The existing patterns are still used for 3 or 4 LEDs.
It was previously not taking into account that the list of pins was sparse,
so using the wrong index. The boards/X/pins.csv was generating the wrong
data for machine.Pin.board.
As part of this fix rename the variables to make it more clear what the
list contains (only board pins).
This commit adds support for sys.settrace, allowing to install Python
handlers to trace execution of Python code. The interface follows CPython
as closely as possible. The feature is disabled by default and can be
enabled via MICROPY_PY_SYS_SETTRACE.
mp_compile no longer takes an emit_opt argument, rather this setting is now
provided by the global default_emit_opt variable.
Now, when -X emit=native is passed as a command-line option, the emitter
will be set for all compiled modules (included imports), not just the
top-level script.
In the future there could be a way to also set this variable from a script.
Fixes issue #4267.
- Split 'qemu-arm' from 'unix' for generating tests.
- Add frozen module to the qemu-arm test build.
- Add test that reproduces the requirement to half-word align native
function data.
Enabled via MICROPY_PY_URE_DEBUG, disabled by default (but enabled on unix
coverage build). This is a rarely used feature that costs a lot of code
(500-800 bytes flash). Debugging of regular expressions can be done
offline with other tools.
As per PEP 485, this function appeared in for Python 3.5. Configured via
MICROPY_PY_MATH_ISCLOSE which is disabled by default, but enabled for the
ports which already have MICROPY_PY_MATH_SPECIAL_FUNCTIONS enabled.
Before this patch I2C transactions using a hardware I2C peripheral on F0/F7
MCUs would not correctly generate the I2C restart condition, and instead
would generate a stop followed by a start. This is because the CR2 AUTOEND
bit was being set before CR2 START when the peripheral already had the I2C
bus from a previous transaction that did not generate a stop.
As a consequence all combined transactions, eg read-then-write for an I2C
memory transfer, generated a stop condition after the first transaction and
didn't generate a stop at the very end (but still released the bus). Some
I2C devices require a repeated start to function correctly.
This patch fixes this by making sure the CR2 AUTOEND bit is set after the
start condition and slave address have been fully transferred out.
Replaces the `SDKCONFIG` makefile variable with `BOARD`. Defaults to
BOARD=GENERIC. spiram can be enabled with `BOARD=GENERIC_SPIRAM`
Add example definition for TINYPICO, currently identical to GENERIC_SPIRAM
but with custom board/SoC names for the uPy banner.
They are both enabled by default, but can be disabled by defining
MICROPY_HW_ENABLE_MDNS_QUERIES and/or MICROPY_HW_ENABLE_MDNS_RESPONDER to
0. The hostname for the responder is currently taken from
tcpip_adapter_get_hostname() but should eventually be configurable.
This commit adds the connect() method to the PPP interface and requires
that connect() be called after active(1). This is a breaking change for
the PPP API.
With the connect() method it's now possible to pass in authentication
information for PAP/CHAP, eg:
ppp.active(1)
ppp.connect(authmode=ppp.AUTH_PAP, username="user", "password="password")
If no authentication is needed simply call connect() without any
parameters. This will get the original behaviour of calling active(1).
Some SD/MMC breakout boards don't support 4-bit bus mode. This adds a new
macro MICROPY_HW_SDMMC_BUS_WIDTH that allows each board to define the width
of the SD/MMC bus interface used on that board, defaulting to 4 bits.
The previous version did not work on MCUs that only had USB device mode
(compared to OTG) because of the handling of NAK. And this previous
handling of NAK had a race condition where a new packet could come in
before USBD_HID_SetNAK was called (since USBD_HID_ReceivePacket clears NAK
as part of its operation). Furthermore, the double buffering of incoming
reports was not working, only one buffer could be used at a time.
This commit rewrites the HID interface code to have a single incoming
buffer, and only calls USBD_HID_ReceivePacket after the user has read the
incoming report (similar to how the VCP does its flow control). As such,
USBD_HID_SetNAK and USBD_HID_ClearNAK are no longer needed.
API functionality from the user's point of view should be unchanged with
this commit.
On this port the GIL is enabled and everything works under the assumption
of the GIL, ie that a given task has exclusive access to the uPy state, and
any ISRs interrupt the current task and therefore the ISR inherits
exclusive access to the uPy state for the duration of its execution.
If the MicroPython tasks are not pinned to a specific core then an ISR may
be executed on a different core to the task, making it possible for the
main task and an ISR to execute in parallel, breaking the assumption of the
GIL.
The easiest and safest fix for this is to pin all MicroPython related code
to the same CPU core, as done by this patch. Then any ISR that accesses
MicroPython state must be registered from a MicroPython task, to ensure it
is invoked on the same core.
See issue #4895.
The C++ standard forbids redefining keywords, like inline and alignof, so
guard these definitions to avoid that, allowing to include the MicroPython
headers by C++ code.
This new series of MCUs is similar to the L4 series with an additional
Cortex-M0 coprocessor. The firmware for the wireless stack must be managed
separately and MicroPython does not currently interface to it. Supported
features so far include: RTC, UART, USB, internal flash filesystem.
The new configurations MICROPY_HW_USB_MSC and MICROPY_HW_USB_HID can be
used by a board to enabled or disable MSC and/or HID. They are both
enabled by default.
In a non-thread build, using &_ram_end as the top-of-stack is no longer
correct because the stack is not always at the very top end of RAM. See
eg 04c7cdb668 and
3786592097. The correct value to use is
&_estack, which is the value stored in MP_STATE_THREAD(stack_top), and
using the same code for both thread and non-thread builds makes the code
cleaner.
stm32lib now provides system_stm32XXxx.c source files for all MCU variants,
which includes SystemInit and prescaler tables. Since these are quite
standard and don't need to be changed, switch to use them instead of custom
variants, making the start-up code cleaner.
The SystemInit code in stm32lib was checked and is equivalent to what is
removed from the stm32 port in this commit.
Without this you often don't get any DNS server from your network provider.
Additionally, setting your own DNS _does not work_ without this option set
(which could be a bug in the PPP stack).
This is a start to make a more consistent machine.RTC class across ports.
The stm32 pyb.RTC class at least has the datetime() method which behaves
the same as esp8266 and esp32, and with this patch the ntptime.py script
now works with stm32.
If both FS and HS USB peripherals are enabled for a board then the active
one used for the REPL will now be auto-detected, by checking to see if both
the DP and DM lines are actively pulled low. By default the code falls
back to use MICROPY_HW_USB_MAIN_DEV if nothing can be detected.
When going out of memory-mapped mode to do a control transfer to the QSPI
flash, the MPU settings must be changed to forbid access to the memory
mapped region. And any ongoing transfer (eg memory mapped continuous read)
must be aborted.
The Cortex-M7 CPU will do speculative loads from any memory location that
is not explicitly forbidden. This includes the QSPI memory-mapped region
starting at 0x90000000 and with size 256MiB. Speculative loads to this
QSPI region may 1) interfere with the QSPI peripheral registers (eg the
address register) if the QSPI is not in memory-mapped mode; 2) attempt to
access data outside the configured size of the QSPI flash when it is in
memory-mapped mode. Both of these scenarios will lead to issues with the
QSPI peripheral (eg Cortex bus lock up in scenario 2).
To prevent such speculative loads from interfering with the peripheral the
MPU is configured in this commit to restrict access to the QSPI mapped
region: when not memory mapped the entire region is forbidden; when memory
mapped only accesses to the valid flash size are permitted.
When compiled with hard float the system should enable FP access when it
starts or else FP instructions lead to a fault. But this minimal port does
not enable (or use) FP and so, to keep it minimal, switch to use soft
floating point. (This became an issue due to the recent commit
34c04d2319 which saves/restores FP registers
in the NLR state.)
Change static LED functions to lowercase names, and trim down source code
lines for variants of MICROPY_HW_LED_COUNT. Also rename configuration for
MICROPY_HW_LEDx_LEVEL to MICROPY_HW_LEDx_PULLUP to align with global PULLUP
configuration.
Commit 9e68eec8ea introduced a regression
where the PID of the USB device would be 0xffff if the default value was
used. This commit fixes that by using a signed int type.
Entering a bootloader (ST system bootloader, or custom mboot) from software
by directly branching to it is not reliable, and the reliability of it
working can depend on the peripherals that were enabled by the application
code. It's also not possible to branch to a bootloader if the WDT is
enabled (unless the bootloader has specific provisions to feed the WDT).
This patch changes the way a bootloader is entered from software by first
doing a complete system reset, then branching to the desired bootloader
early on in the start-up process. The top two words of RAM (of the stack)
are reserved to store flags indicating that the bootloader should be
entered after a reset.
WIFI_REASON_AUTH_FAIL does not necessarily mean the password is wrong, and
a wrong password may not lead to a WIFI_REASON_AUTH_FAIL error code. So to
improve reliability connecting to a WLAN always reconnect regardless of the
error.
This updates ESP IDF to use v3.3-beta3. And also adjusts README.md to
point to stable docs which provide a link to download the correct toolchain
for this IDF version, namely 1.22.0-80-g6c4433a-5.2.0
Previously the end of the heap was the start (lowest address) of the stack.
With the changes in this commit these addresses are now independent,
allowing a board to place the heap and stack in separate locations.
With this the user can select multiple logical units to expose over USB MSC
at once, eg: pyb.usb_mode('VCP+MSC', msc=(pyb.Flash(), pyb.SDCard())). The
default behaviour is the original behaviour of just one unit at a time.
Eventually these responses could be filled in by a function to make their
contents dynamic, depending on the attached logical units. But for now
they are fixed, and this patch fixes the MODE SENSE(6) responses so it is
the correct length with the correct header.
SCSI can support multiple logical units over the one interface (in this
case over USBD MSC) and here the MSC code is reworked to support this
feature. At this point only one LU is used and the behaviour is mostly
unchanged from before, except the INQUIRY result is different (it will
report "Flash" for both flash and SD card).
To use it a board should define MICROPY_PY_USSL=1 and MICROPY_SSL_MBEDTLS=1
at the Makefile level. With the provided configuration it adds about 64k
to the build.
It doesn't work to tie the polling of an underlying NIC driver (eg to check
the NIC for pending Ethernet frames) with its associated lwIP netif. This
is because most NICs are implemented with IRQs and don't need polling,
because there can be multiple lwIP netif's per NIC driver, and because it
restricts the use of the netif->state variable. Instead the NIC should
have its own specific way of processing incoming Ethernet frame.
This patch removes this generic NIC polling feature, and for the only
driver that uses it (Wiznet5k) replaces it with an explicit call to the
poll function (which could eventually be improved by using a proper
external interrupt).
This adds support for SD cards using the ESP32's built-in hardware SD/MMC
host controller, over either the SDIO bus or SPI. The class is available
as machine.SDCard and using it can be as simple as:
uos.mount(machine.SDCard(), '/sd')
If the board-pin name is left empty then only the cpu-pin name is used, eg
",PA0". If the board-pin name starts with a hyphen then it's available as
a C definition but not in the firmware, eg "-X1,PA0".
The patch solves the problem where multiple Timer objects (e.g. multiple
Timer(0) instances) could initialise multiple handles to the same internal
timer. The list of timers is now maintained not for "active" timers (where
init is called), but for all timers created. The timers are only removed
from the list of timers on soft-reset (machine_timer_deinit_all).
Fixes#4078.
The board config option MICROPY_HW_USB_ENABLE_CDC2 is now changed to
MICROPY_HW_USB_CDC_NUM, and the latter should be defined to the maximum
number of CDC interfaces to support (defaults to 1).
Set the active MPU region to the actual size of SDRAM configured and
invalidate the rest of the memory-mapped region, to prevent errors due to
CPU speculation. Also update the attributes of the SDRAM region as per ST
recommendations, and change region numbers to avoid conflicts elsewhere in
the codebase (see eth usage).
I2C can't be enabled in prj_base.conf because it's a board-specific
feature. For example, if a board doesn't have I2C but CONFIG_I2C=y then
the build will fail (on Zephyr build system side). The patch here gets the
qemu_cortex_m3 build working again.
This enables going back to previous wrapped lines using backspace or left
arrow: instead of just sticking to the beginning of a line, the cursor will
move a line up.
On MCUs that have an I2C TIMINGR register, this can now be explicitly set
via the "timingr" keyword argument to the I2C constructor, for both
machine.I2C and pyb.I2C. This allows to configure precise timing values
when the defaults are inadequate.
Previously the hardware I2C timeout was hard coded to 50ms which isn't
guaranteed to be enough depending on the clock stretching specs of the I2C
device(s) in use.
This patch ensures the hardware I2C implementation honors the existing
timeout argument passed to the machine.I2C constructor. The default
timeout for software and hardware I2C is now 50ms.
Recent gcc versions (at least 9.1) give a warning about using "sp" in the
clobber list. Such code is removed by this patch. A dedicated function is
instead used to set SP and branch to the bootloader so the code has full
control over what happens.
Fixes issue #4785.
This also fixes deleting the PPP task, since eTaskGetState() never returns
eDeleted.
A limitation with this patch: once the PPP is deactivated (ppp.active(0))
it cannot be used again. A new PPP instance must be created instead.
This allows figuring out the number of bytes in the memoryview object as
len(memview) * memview.itemsize.
The feature is enabled via MICROPY_PY_BUILTINS_MEMORYVIEW_ITEMSIZE and is
disabled by default.
The original code called setsockopt(SO_RCVTIMEO/SO_SNDTIMEO) with NULL
timeout structure argument, which is an illegal usage of that function.
The old code also didn't validate the return value of setsockopt, missing
the bug completely.
Before this change, if the USB was reconnected it was possible that some
characters in the TX buffer were retransmitted because tx_buf_ptr_out and
tx_buf_ptr_out_shadow were reset while tx_buf_ptr_in wasn't. That
behaviour is fixed here by retaining the TX buffer state across reconnects.
Fixes issue #4761.
The new function factory_reset_make_files() populates the given filesystem
with the default factory files. It is defined with weak linkage so it can
be overridden by a board.
This commit also brings some minor user-facing changes:
- boot.py is now no longer created unconditionally if it doesn't exist, it
is now only created when the filesystem is formatted and the other files
are populated (so, before, if the user deleted boot.py it would be
recreated at next boot; now it won't be).
- pybcdc.inf and README.txt are only created if the board has USB, because
they only really make sense if the filesystem is exposed via USB.
It's more common to need non-blocking behaviour when reading from a UART,
rather than having a large timeout like 1000ms (the original behaviour).
With a large timeout it's 1) likely that the function will read forever if
characters keep trickling it; or 2) the function will unnecessarily wait
when characters come sporadically, eg at a REPL prompt.
- IBK-BLYST-NANO: Breakout board
- IDK-BLYST-NANO: DevKit board with builtin IDAP-M CMSIS-DAP Debug JTAG,
RGB led
- BLUEIO-TAG-EVIM: Sensor tag board (environmental sensor
(T, H, P, Air quality) + 9 axis motion sensor)
Also, the LED module has been updated to support individual base level
configuration of each LED. If set, this will be used instead of the
common configuration, MICROPY_HW_LED_PULLUP. The new configuration,
MICROPY_HW_LEDX_LEVEL, where X is the LED number can be used to set
the base level of the specific LED.
The alternate function pin allocations are different to other NUCLEO-144
boards. This is because the STM32F413 has a very high peripheral count:
10x UART, 5x SPI, 3x I2C, 3x CAN. The pinout was chosen to expose all
these devices on separate pins except CAN3 which shares a pin with UART1
and SPI1 which shares pins with DAC.
Includes:
- Support for CAN3.
- Support for UART9 and UART10.
- stm32f413xg.ld and stm32f413xh.ld linker scripts.
- stm32f413_af.csv alternate function mapping.
- startup_stm32f413xx.s because F413 has different interrupt vector table.
- Memory configuration with: 240K filesystem, 240K heap, 16K stack.
This patch makes pllvalues.py generate two tables: one for when HSI is used
and one for when HSE is used. The correct table is then selected at
compile time via the existing MICROPY_HW_CLK_USE_HSI.
When building with link time optimization enabled it is possible both
gc_collect() and gc_collect_regs_and_stack() get inlined into gc_alloc()
which can result in the regs variable being pushed on the stack earlier
than some of the registers. Depending on the calling convention, those
registers might however contain pointers to blocks which have just been
allocated in the caller of gc_alloc(). Then those pointers end up higher on
the stack than regs, aren't marked by gc_collect_root() and hence get
sweeped, even though they're still in use.
As reported in #4652 this happened for in 32-bit msvc release builds:
mp_lexer_new() does two consecutive allocations and the latter triggered a
gc_collect() which would sweep the memory of the first allocation again.
The machine.WDT() now accepts the "timeout" keyword argument to select the
WDT interval. And the WDT is changed to panic mode which means it will
reset the device if the interval expires (instead of just printing an error
message).
On the STM32F722 (at least, but STM32F767 is not affected) the CK48MSEL bit
must be deselected before PLLSAION is turned off, or else the 48MHz
peripherals (RNG, SDMMC, USB) may get stuck without a clock source.
In such "lock up" cases it seems that these peripherals are still being
clocked from the PLLSAI even though the CK48MSEL bit is turned off. A hard
reset does not get them out of this stuck state. Enabling the PLLSAI and
then disabling it does get them out. A test case to see this is:
import machine, pyb
for i in range(100):
machine.freq(122_000000)
machine.freq(120_000000)
print(i, [pyb.rng() for _ in range(4)])
On occasion the RNG will just return 0's, but will get fixed again on the
next loop (when PLLSAI is enabled by the change to a SYSCLK of 122MHz).
Fixes issue #4696.
The stm32 and nrf ports already had the behaviour that they would first
check if the script exists before executing it, and this patch makes all
other ports work the same way. This helps when developing apps because
it's hard to tell (when unconditionally trying to execute the scripts) if
the resulting OSError at boot up comes from missing boot.py or main.py, or
from some other error. And it's not really an error if these scripts don't
exist.
This patch makes the DAC driver simpler and removes the need for the ST
HAL. As part of it, new helper functions are added to the DMA driver,
which also use direct register access instead of the ST HAL.
Main changes to the DAC interface are:
- The DAC uPy object is no longer allocated dynamically on the heap,
rather it's statically allocated and the same object is retrieved for
subsequent uses of pyb.DAC(<id>). This allows to access the DAC objects
without resetting the DAC peripheral. It also means that the DAC is only
reset if explicitly passed initialisation parameters, like "bits" or
"buffering".
- The DAC.noise() and DAC.triangle() methods now output a signal which is
full scale (previously it was a fraction of the full output voltage).
- The DAC.write_timed() method is fixed so that it continues in the
background when another peripheral (eg SPI) uses the DMA (previously the
DAC would stop if another peripheral finished with the DMA and shut the
DMA peripheral off completely).
Based on the above, the following backwards incompatibilities are
introduced:
- pyb.DAC(id) will now only reset the DAC the first time it is called,
whereas previously each call to create a DAC object would reset the DAC.
To get the old behaviour pass the bits parameter like: pyb.DAC(id, bits).
- DAC.noise() and DAC.triangle() are now full scale. To get previous
behaviour (to change the amplitude and offset) write to the DAC_CR (MAMP
bits) and DAC_DHR12Rx registers manually.
If MICROPY_HW_RTC_USE_BYPASS is enabled the RTC startup goes as follows:
- RTC is started with LSE in bypass mode to begin with
- if that fails to start (after a given timeout) then LSE is reconfigured
in non-bypass
- if that fails to start then RTC is switched to LSI
Use uos.dupterm for REPL configuration of the main USB_VCP(0) stream on
dupterm slot 1, if USB is enabled. This means dupterm can also be used to
disable the boot REPL port if desired, via uos.dupterm(None, 1).
For efficiency this adds a simple hook to the global uos.dupterm code to
work with streams that are known to be native streams.
These macros are unused, and they can conflict with other entities by the
same name. If needed they can be provided as static inline functions, or
just functions.
Fixes issue #4559.
Adds support for hardware i2c to the zephyr port. Similar to other ports
such as stm32 and nrf, we only implement the i2c protocol functions
(readfrom and writeto) and defer memory operations (readfrom_mem,
readfrom_mem_into, and writeto_mem) to the software i2c implementation.
This may need to change in the future because zephyr is considering
deprecating its i2c_transfer function in favor of i2c_write_read; in this
case we would probably want to implement the memory operations directly
using i2c_write_read.
Tested with the accelerometer on frdm_k64f and bbc_microbit boards.
For gpio_hold_en() to work properly (not draw additional current) pull
up/down must be disabled when hold is enabled. This patch makes sure this
is the case by reworking the pull constants to be a bit mask.
Adding section about on how to disable use of the linker flag
-flto, by setting the LTO=0 argument to Make. Also, added a
note on recommended toolchains to use that works well with
LTO enabled.
Removing linker script for nrf52840 s140 v6.0.0 as pca10056
target board now points to the new v6.1.1. Also, removing the
entry from the download_ble_stack.sh script.
Removing linker script for nrf52832 s132 v6.0.0 as all target
boards now points to the new v6.1.1. Also, removing the entry
from the download_ble_stack.sh script.
Previously specifying None as the pull value would leave the pull up/down
state unchanged. This change makes it so -1 leaves the state unchanged and
None makes the pin float, as per the docs.
In this port JavaScript is the underlying "machine" and MicroPython is
transmuted into JavaScript by Emscripten. MicroPython can then run under
Node.js or in the browser.
Functions in these files may be needed when certain features are enabled
(eg dual core mode), even if the linker does not give a warning or error
about unresolved symbols.
During make, makemoduledefs.py parses the current builds c files for
MP_REGISTER_MODULE(module_name, obj_module, enabled_define)
These are used to generate a header with the required entries for
"mp_rom_map_elem_t mp_builtin_module_table[]" in py/objmodule.c
To use HSI instead of HSE define MICROPY_HW_CLK_USE_HSI as 1 in the board
configuration file. The default is to use HSE.
HSI has been made the default for the NUCLEO_F401RE board to serve as an
example, and because early revisions of this board need a hardware
modification to get HSE working.
This demonstrates how to use external QSPI flash in XIP (execute in place)
mode. The default configuration has all extmod/ code placed into external
QSPI flash, but other code can easily be put there by modifying the custom
f769_qspi.ld script.
A board can now use the make variables TEXT0_SECTIONS and TEXT1_SECTIONS to
specify the linker sections that should go in its firmware. Defaults are
provided which give the existing behaviour.
esp_wifi_connect will return ESP_OK for the normal path of execution which
just means the reconnect is started, not that it is actually reconnected.
In such a case wifi.isconnected() should return False until the
reconnection is complete. After reconnect a GOT_IP event is called and it
will change wifi_sta_connected back to True.
This patch makes sure that the char_data.props is first
assigned a value before other flags are OR'd in.
Resolves compilation warning on possible unitialized variable.
This patch makes sure that advertisment data is located in
persistent static RAM memory throughout the advertisment.
Also, setting m_adv_handle to predifined
BLE_GAP_ADV_SET_HANDLE_NOT_SET value to indicate first time
usage of the handle. Upon first advertisment configuration
this will be populated with a handle value returned by the
stack (s132/s140).
After new layout of nordicsemi.com the direct links to
command line tools (nrfjprog) has changed to become dynamic.
This patch removes the old direct links to each specific OS
variant and is replaced with one single link to the download
landing page instead.
Currently all usages of mp_hal_pin_config_alt_static() set the pin speed to
"high" (50Mhz). The SDRAM interface typically runs much faster than this
so should be set to the maximum pin speed.
This commit adds mp_hal_pin_config_alt_static_speed() which allows setting
the pin speed along with the other alternate function details.
A few RTC constants weren't being parsed properly due to whitespace
differences, and this patch makes certain whitespace optional. Changes
made:
- allow for no space between /*!< and EXTI, eg for:
__IO uint32_t IMR; /*!<EXTI Interrupt mask register, Address offset: 0x00 */
- allow for no space between semicolon and start of comment, eg for:
__IO uint32_t ALRMASSR;/*!< RTC alarm A sub second register, Address offset: 0x44 */
As mentioned in #4450, `websocket` was experimental with a single intended
user, `webrepl`. Therefore, we'll make this change without a weak
link `websocket` -> `uwebsocket`.
If opening of /dev/mem has failed an `OSError` is appropriately raised, but
the next time `mem8/16/32` is accessed the invalid file descriptor is used
and the program gets a SIGSEGV.
Replaces "PYB: soft reboot" with "MPY: soft reboot", etc.
Having a consistent prefix across ports reduces the difference between
ports, which is a general goal. And this change won't break pyboard.py
because that tool only looks for "soft reboot".
Adds support for 3 Cortex-M boards, selectable via "BOARD" in the Makefile:
- microbit, Cortex-M0 via nRF51822
- netduino2, Cortex-M3 via STM32F205
- mps2-an385, Cortex-M3 via FPGA
netduino2 is the default board because it's supported by older qemu
versions (down to at least 2.5.0).
Instead of checking each callback (currently storage and dma) explicitly
for each SysTick IRQ, use a simple circular function table indexed by the
lower bits of the millisecond tick counter. This allows callbacks to be
easily enabled/disabled at runtime, and scales well to a large number of
callbacks.
This is a good board to demonstrate the use of Mboot because it only has a
USB HS port exposed so the native ST DFU mode cannot be used. With Mboot
this port can be used.
If a custom bootloader is enabled (eg mboot) then machine.bootloader() will
now enter that loader. To get the original ST DFU loader pass any argument
to the function, like machine.bootloader(1).
Don't exclude the Timer instance 1 entry from machine_timer_obj[] when
using soft PWM. The usage is already checked when creating the Timer,
so just create an empty entry.
If needed these parameters can be added back and made functional one at a
time. It's better to explicitly not support them than to silently allow
but ignore them.
Python defines warnings as belonging to categories, where category is a
warning type (descending from exception type). This is useful, as e.g.
allows to disable warnings selectively and provide user-defined warning
types. So, implement this in MicroPython, except that categories are
represented just with strings. However, enough hooks are left to implement
categories differently per-port (e.g. as types), without need to patch each
and every usage.
With clock bypass enabled the attached SD card is clocked at the maximum
48MHz. But some SD cards are unreliable at these rates. Although it's
nice to have high speed transfers it's more important that the transfers
are reliable for all cards. So disable this clock bypass option.
This way the UART REPL does not need the MicroPython heap and exists
outside the MicroPython runtime, allowing characters to still be received
during a soft reset.
Auto-detection of the crystal frequency is convenient and allows for a
single binary for many different boards. But it can be unreliable in
certain situations so in production, for a given board, it's recommended to
configure the correct fixed frequency.
Configuration for the build is now specified using sdkconfig rather than
sdkconfig.h, which allows for much easier configuration with defaults from
the ESP IDF automatically applied. sdkconfig.h is generated using the new
ESP IDF kconfig_new tool written in Python. Custom configuration for a
particular ESP32 board can be specified via the make variable SDKCONFIG.
The esp32.common.ld file is also now generated using the standard ESP IDF
ldgen.py tool.
When the ESP IDF builds a project it puts all separate components into
separate .a library archives. And then the esp32.common.ld linker script
references these .a libraries by explicit name to put certain object files
in iRAM.
This patch does a similar thing for the custom build system used here,
putting all IDF .o's into their respective .a. So a custom linker script
is no longer needed.
ISR's no longer need to be in iRAM, and the ESP IDF provides an option to
specify that they are in iRAM if an application needs lower latency when
handling them. But we don't use this feature for user interrupts: both
timer and gpio ISR routines are registered without the ESP_INTR_FLAG_IRAM
option, and so the scheduling code no longer needs to be in iRAM.
The new compile-time option is MICROPY_HW_USB_MAX_POWER_MA. Set this in
the board configuration file to the maximum current in mA that the board
will draw over USB. The default is 500mA.
The new compile-time option is MICROPY_HW_USB_SELF_POWERED. Set this
option to 1 in the board configuration file to indicate that the USB device
is self powered. This option is disabled by default (previous behaviour).
It can be that LSEON and LSERDY are set yet the RTC is not enabled (this
can happen for example when coming out of the ST DFU mode on an F405 with
the RTC not previously initialised). In such a case the RTC is never
started because the code thinks it's already running. This patch fixes
this case by always checking if RTCEN is set when booting up (and also
testing for a valid RTCSEL value in the case of using an LSE).
One can't use pthread calls in a signal handler because they are not
async-signal-safe (see man signal-safety). Instead, sem_post can be used
to post from within a signal handler and this should be more efficient than
using a busy wait loop, waiting on a volatile variable.
This aligns more closely with the hardware, that there are two, fixed HW
SPI peripherals. And it allows to recreate the HW SPI objects without
error, as well as create them again after a soft reset.
Fixes issue #4103.
In order to suit the more common 800KHz by default (instead of 400KHz), and
also have the same behaviour as the esp8266 port.
Resolves#4396.
Note! This is a breaking change. Anyone that has previously used the
NeoPixel class on an ESP32 board may be affected.
The original behaviour of open-drain-high was to use the open-drain mode of
the GPIO pin, and this seems to make driving a DHT more reliable. See
issue #4233.
The ESP IDF system already provides a math library, and that one is likely
to be better tuned to the Xtensa architecture. The IDF components are also
tested against its own math library, so best not to override it. Using the
system provided library also allows to easily switch to double-precision
floating point by changing MICROPY_FLOAT_IMPL to MICROPY_FLOAT_IMPL_DOUBLE.
So that the user can explicitly deactivate UART(0) if needed. See
issue #4314.
This introduces some risk to "brick" the device, if the user disables the
REPL without providing an alternative REPL (eg WebREPL), or any way to
reenable it. In such a case the device needs to be erased and
reprogrammed. This seems unavoidable, given the desire to have the option
to use the UART for something other than the REPL.
Without the static qualifier these objects will be kept by the linker even
if they are unused. So this patch saves some RAM when these features are
unused by a board.
If there are many short reads to a socket in a row (eg by readline) then
releasing and acquiring the GIL each time will give very poor throughput.
So first poll the socket to see if it has data, and if it does then don't
release the GIL.
Otherwise, if multiple threads are active, printing data to the REPL may be
very slow because in some cases only one character is output per call to
mp_hal_stdout_tx_strn.
On MCUs other than F4 the ORE (overrun error) flag needs to be cleared
independently of clearing RXNE, even though both are wired to trigger the
same RXNE IRQ. In the case that an overrun occurred it's necessary to
explicitly clear the ORE flag or else the RXNE interrupt will keep firing.
Otherwise IRQs may not be enabled for the user UART.irq() handler. In
particular this fixes the user IRQ_RXIDLE interrupt so that it triggers
even when there is no RX buffer.
The new option MICROPY_HW_SDCARD_MOUNT_AT_BOOT can now be defined to 0 in
mpconfigboard.h to allow SD hardware to be enabled but not auto-mounted at
boot. This feature is enabled by default to retain previous behaviour.
Previously, if an SD card is enabled in hardware it is also used to boot
from. While this can be disabled with a SKIPSD file on internal flash,
this wont be available at first boot or if the internal flash gets
corrupted.
Due to new webpages at nordicsemi.com, the download links
for Bluetooth LE stacks were broken.
This patch updates the links to new locations for the current
targets.
This UART_HandleTypeDef is quite large (around 70 bytes in RAM needed for
each UART object) and is not needed: instead the state of the peripheral
held in its registers provides all the required information.
The pin alternate function information is derived from ST's datasheet
https://www.st.com/resource/en/datasheet/stm32l432kc.pdf
In the datasheet, the line 2 of AF4 includes I2C2 but actually the chip
does not have I2C2 so it is removed.
As per the machine.UART documentation, this is used to set the length of
the RX buffer. The legacy read_buf_len argument is retained for backwards
compatibility, with rxbuf overriding it if provided.
Also change the order of printing of flow so it is after stop (so bits,
parity, stop are one after the other), and reduce code size by using
mp_print_str instead of mp_printf where possible.
See issue #1981.
This is necessary for two reasons: 1) FreeRTOS still needs the TCB data
structure even after vPortCleanUpTCB has been called, so this latter hook
function cannot free the TCB, and there is no where else to safely delete
it (this behaviour has changed recently in the ESP IDF); 2) when using
external SPI RAM the uPy heap is in this external memory but the task stack
must be allocated from internal SRAM.
Fixes issue #3904.
We standardized to provide uos.remove() as a more obvious and user-friendly
name. That's what written in the docs. The Unix port implementation
predates this convention, so update it now.
Building axtls gives a lot of warnings with -Wall enabled, and explicitly
disabling all of them cannot be done in a way compatible with gcc and
clang, and likely other compilers. So just use -Wno-all to prevent all of
the extra warnings (in addition to the necessary -Wno-unused-parameter,
-Wno-uninitialized, -Wno-sign-compare and -Wno-old-style-definition).
Fixes issue #4182.
Configurable via MICROPY_MODULE_GETATTR, disabled by default. Among other
things __getattr__ for modules can help to build lazy loading / code
unloading at runtime.
Configurable via MICROPY_PY_BUILTINS_STR_COUNT. Default is enabled.
Disabled for bare-arm, minimal, unix-minimal and zephyr ports. Disabling
it saves 408 bytes on x86.
1. Return correct error code for non-blocking vs timed out socket
(POSIX returns EAGAIN for both, we want ETIMEDOUT in case of timed
out socket). To achieve this, blocking/non-blocking flag is added
to the mp_obj_socket_t, to avoid issuing fcntl() syscall each time
EAGAIN occurs. (mp_obj_socket_t used to be 8 bytes, having some room
in a standard 16-byte alloc block.)
2. Handle socket.settimeout(0) properly - in Python, that means
non-blocking mode, but SO_RCVTIMEO/SO_SNDTIMEO of 0 is infinite
timeout.
3. Overall, make sure that socket.settimeout() call switches blocking
state as expected.
Prior to this commit the USB CDC used the USB start-of-frame (SOF) IRQ to
regularly check if buffered data needed to be sent out to the USB host.
This wasted resources (CPU, power) if no data needed to be sent.
This commit changes how the USB CDC transmits buffered data:
- When new data is first available to send the data is queued immediately
on the USB IN endpoint, ready to be sent as soon as possible.
- Subsequent additions to the buffer (via usbd_cdc_try_tx()) will wait.
- When the low-level USB driver has finished sending out the data queued
in the USB IN endpoint it calls usbd_cdc_tx_ready() which immediately
queues any outstanding data, waiting for the next IN frame.
The benefits on this new approach are:
- SOF IRQ does not need to run continuously so device has a better chance
to sleep for longer, and be more responsive to other IRQs.
- Because SOF IRQ is off, current consumption is reduced by a small amount,
roughly 200uA when USB is connected (measured on PYBv1.0).
- CDC tx throughput (USB IN) on PYBv1.0 is about 2.3 faster (USB OUT is
unchanged).
- When USB is connected, Python code that is executing is slightly faster
because SOF IRQ no longer interrupts continuously.
- On F733 with USB HS, CDC tx throughput is about the same as prior to this
commit.
- On F733 with USB HS, Python code is about 5% faster because of no SOF.
As part of this refactor, the serial port should no longer echo initial
characters when the serial port is first opened (this only used to happen
rarely on USB FS, but on USB HS is was more evident).
For s132 and s140, GAP_ADV_MAX_SIZE was currently set to
BLE_GATT_ATT_MTU_DEFAULT, which is 23. The correct value
should have been 31, but there are no define for this in
the s132/s140 header files as for s110.
Updating define in ble_drv.c to the correct value of 31.
The macros are MICROPY_HEAP_START and MICROPY_HEAP_END, and if not defined
by a board then the default values will be used (maximum heap from SRAM as
defined by linker symbols).
As part of this commit the SDRAM initialisation is moved to much earlier in
main() to potentially make it available to other peripherals and avoid
re-initialisation on soft-reboot. On boards with SDRAM enabled the heap
has been set to use that.
Add some more POSIX compatibility by adding a d_type field to the
dirent structure and defining corresponding macros so listdir_next
in the unix' port modos.c can use it, end result being uos.ilistdir
now reports the file type.
This will allow to e.g. implement HTTP Digest authentication.
Adds 540 bytes for x86_32, 332 for arm_thumb2 (for Unix port, which already
includes axTLS library).
This commit adds the math.factorial function in two variants:
- squared difference, which is faster than the naive version, relatively
compact, and non-recursive;
- a mildly optimised recursive version, faster than the above one.
There are some more optimisations that could be done, but they tend to take
more code, and more storage space. The recursive version seems like a
sensible compromise.
The new function is disabled by default, and uses the non-optimised version
by default if it is enabled. The options are MICROPY_PY_MATH_FACTORIAL
and MICROPY_OPT_MATH_FACTORIAL.
Configuring clocks is a critical operation and is best to avoid when
possible. If the clocks really need to be reset to the same values then
one can pass in a slightly higher value, eg 168000001 Hz to get 168MHz.
This ensures that on first boot the most optimal settings are used for the
voltage scaling and flash latency (for F7 MCUs).
This commit also provides more fine-grained control for the flash latency
settings.
Power and clock control is low-level functionality and it makes sense to
have it in a dedicated file, at least so it can be reused by other parts of
the code.
On F7s PLLSAI is used as a 48MHz clock source if the main PLL cannot
provide such a frequency, and on L4s PLLSAI1 is always used as a clock
source for the peripherals. This commit makes sure these PLLs are
re-enabled upon waking from stop mode so the peripherals work.
See issues #4022 and #4178 (L4 specific).
Changes made:
- make use of MP_OBJ_TO_PTR and MP_OBJ_FROM_PTR where necessary
- fix shadowing of index variable i, renamed to j
- fix type of above variable to size_t to prevent comparison warning
- fix shadowing of res variable
- use "(void)" instead of "()" for functions that take no arguments
This part is functionally similar to STM32F767xx (they share a datasheet)
so support is generally comparable. When adding board support the
stm32f767_af.csv and stm32f767.ld should be used.
If DTTOIF() macro is not defined, the code refers to MP_S_IFDIR, etc.
symbols defined in extmod/vfs.h, so should include it.
This fixes build for Android.
The HAL DMA functions enable SDMMC interrupts before fully resetting the
peripheral, and this can lead to a DTIMEOUT IRQ during the initialisation
of the DMA transfer, which then clears out the DMA state and leads to the
read/write not working at all. The DTIMEOUT is there from previous SDMMC
DMA transfers, even those that succeeded, and is of duration ~180 seconds,
which is 0xffffffff / 24MHz (default DTIMER value, and clock of
peripheral).
To work around this issue, fully reset the SDMMC peripheral before calling
the HAL SD DMA functions.
Fixes issue #4110.
The flash-IRQ handler is used to flush the storage cache, ie write
outstanding block data from RAM to flash. This is triggered by a timeout,
or by a direct call to flush all storage caches.
Prior to this commit, a timeout could trigger the cache flushing to occur
during the execution of a read/write to external SPI flash storage. In
such a case the storage subsystem would break down.
SPI storage transfers are already protected against USB IRQs, so by
changing the priority of the flash IRQ to that of the USB IRQ (what is
done in this commit) the SPI transfers can be protected against any
timeouts triggering a cache flush (the cache flush would be postponed until
after the transfer finished, but note that in the case of SPI writes the
timeout is rescheduled after the transfer finishes).
The handling of internal flash sync'ing needs to be changed to directly
call flash_bdev_irq_handler() sync may be called with the IRQ priority
already raised (eg when called from a USB MSC IRQ handler).
MCUs that have a PLLSAI can use it to generate a 48MHz clock for USB, SDIO
and RNG peripherals. In such cases the SYSCLK is not restricted to values
that allow the system PLL to generate 48MHz, but can be any frequency.
This patch allows such configurability for F7 MCUs, allowing the SYSCLK to
be set in 2MHz increments via machine.freq(). PLLSAI will only be enabled
if needed, and consumes about 1mA extra. This fine grained control of
frequency is useful to get accurate SPI baudrates, for example.
A recent version of arm-none-eabi-gcc (8.2.0) will warn about unused packed
attributes in USB_WritePacket and USB_ReadPacket. This patch suppresses
such warnings for this file only.
The aim here is to have spi.c contain the low-level SPI driver which is
independent (not fully but close) of MicroPython objects and methods, and
the higher-level bindings are separated out to pyb_spi.c and machine_spi.c.
Among other things, this requires putting bootloader object files in to
their relevant .a archive, so that they can be correctly referenced by the
ESP IDF's linker script.
- Allow configuration by a board of autorefresh number and burst length.
- Increase MPU region size to 8MiB.
- Make SDRAM region cacheable and executable.
"coverage" build uses different BUILD directory comparing to the normal
build. Previously, any build picked up libaxtls.a from normal build's
directory, but that was fixed recently. So, for each build, we must
build axtls explicitly.
This fixes Travis build in particular.
Use overrideable properties instead of hardcoding the use of the
default cl executable used by msvc toolsets. This allows using
arbitrary compiler commands for qstr header generation.
The CLToolExe and CLToolPath properties are used because they are,
even though absent from any official documentation, the de-facto
standard as used by the msvc toolsets themselves.
Requesting a baudrate of X should never configure the peripheral to have a
baudrate greater than X because connected hardware may not be able to
handle higher speeds. This patch makes sure to round the prescaler up so
that the actual baudrate is rounded down.
Prior to this patch, if VBAT was read via ADC.read() or
ADCAll.read_channel(), then it would remain enabled and subsequent reads
of TEMPSENSOR or VREFINT would not work. This patch makes sure that VBAT
is disabled for all cases that it could be read.
This patch in effect renames MICROPY_DEBUG_PRINTER_DEST to
MICROPY_DEBUG_PRINTER, moving its default definition from
lib/utils/printf.c to py/mpconfig.h to make it official and documented, and
makes this macro a pointer rather than the actual mp_print_t struct. This
is done to get consistency with MICROPY_ERROR_PRINTER, and provide this
macro for use outside just lib/utils/printf.c.
Ports are updated to use the new macro name.
The NRF52 define only covers nrf52832, so update the define checks
to use NRF52_SERIES to cover both nrf52832 and nrf52840.
Fixed machine_hard_pwm_instances table in modules/machine/pwm.c
This enables PWM(0) to PWM(3), RTCounter(2), Timer(3) and Timer(4),
in addition to NFC reset cause, on nrf52840.
When waking from stop mode most of the system is still in the same state as
before entering stop, so only minimal configuration is needed to bring the
system clock back online.
A recent version of arm-none-eabi-gcc (8.2.0) will warn about unused packed
attributes in USB_WritePacket and USB_ReadPacket. This patch suppresses
such warnings for this file only.
Works with pins declared normally in mpconfigboard.h, eg. (pin_XX), as well
as (pyb_pin_XX).
Provides new mp_hal_pin_config_alt_static(pin_obj, mode, pull, fn_type)
function declared in pin_static_af.h to allow configuring pin alternate
functions by name at compile time.
This mechanism will scale to to an arbitrary number of pollable objects, so
long as they implement the MP_STREAM_GET_FILENO ioctl. Since ussl objects
pass through ioctl requests transparently to the underlying socket object,
it will allow ussl sockets to be polled. And a user object with uio.IOBase
as a base could support polling.
The code was dereferencing 0x800 and loading a value from there, trying to
use a literal value (not address) defined in the linker script
(_ram_fs_cache_block_size) which was 0x800.
Adding MICROPY_FATFS as makefile flag in order to explicitly
include oofatfs files to be compiled into the build.
The flag is set to 0 by default. Must be set in addition to
MICROPY_VFS and MICROPY_VFS_FAT in mpconfigport.h.
Temporarly solving the issue of
"differ from the size of original declaration [-Werror=lto-type-mismatch]
until linker is fixed in upcomming release of gcc.
Bug is reported by others, and will be fixed in next version of arm-gcc.
However, this patch makes it possible to use modmusic and modimage
with current compilers.
Alternativly, the code can be compiled with LTO=0, but uses valuable 9K
more on this already squeezed target (microbit).
Support added for s132/s140 v6 in linker scripts and boards.
Support removed for s132 v2/3/5.
Download script updated to fetch new stacks and removed the
non-supported ones.
ble_drv.c updated to only handle s110 v8, and s132/s140 v6.
ubluepy updated to continue scanning after each individual scan
report reported to the module to keep old behaviour of the
Scanner class.
This patch generalize the feather52 target to be a board without
an in-built Bluetooth stack or bootloader giving all flash memory to
micropython code.
This way the feather52 target can run any supported Bluetooth LE
stack the port supports for other nrf52832 targets. Hence, this
make Makefiles/linker scripts and BLE driver support easier
to maintain in the future.
Current adoption on top of nrfx only reads the GPIO->IN register.
In order to read back an output state, nrf_gpio_pin_out_read has
to be called.
This patch concatinate the two read functions such that, if
either IN or OUT register has a value 1 it will return this,
else 0.
Updating lib/nrfx submodule to latest version of master to get
the new GPIO API to read pin direction.
(nrfx: d37b16f2b894b0928395f6f56ca741287a31a244)
Cleaning up use of "pyb" module.
Moving the file to a new folder and updating the
makefile accordingly. New module created called
"board" to take over the functionality of the legacy
"pyb" module.
Updating outdated documentation referring to pyb.Pin,
to now point to machine.Pin.
As EasyDMA variant of SPI(M) might clock out an additional byte
in single byte transactions this patch moves the nrf52832 to
use SPI and not SPIM to get more stable data transactions.
Ref: nrf52832 rev2 errata v1.1, suggested workaround is:
"Use the SPI module (deprecated but still available) or
use the following workaround with SPIM ..."
Current nrfx SPIM driver does not contain this workaround,
and in the meanwhile moving back to SPI fixes the issue.
Also, tabbing the nrfx_config.h a bit to make it more readable.
This patch moves the check of SPI configuration before
including any SPI header files. As targets might disable SPI
support, current code ends up in including SPIM if not SPI
is configured. Hence, this is why the check whether the module is
enabled should be done before including headers.
dfu-gen .PHONY target is run unconditionally as first build
target when included, and might fail if the hex file is not
yet generated.
To prevent this, the dfu-gen and dfu-flash targets are moved
to the main Makefile and only exposed if feather52 is the
defined BOARD.
Update configuration define from
MICROPY_HW_HAS_BUILTIN_FLASH to MICROPY_MBFS.
MICROPY_MBFS will enable the builtin flash as
part of enabling the micro:bit FS.
Clang understands only -fshort-enums, not --short-enums. As
--short-enums isn't even mentioned in the gcc man page, I think this
alias exists more for backwards compatibility.
Removing unused nrf52832_512k_64k_s132_5.0.0.ld.
Adding new linker script s132_5.0.0 following new
linker script scheme.
Updating ble_drv.c to handle de-increment of
outstanding tx packets on hvx for s132 v5.
After nrfx 1.0.0 a new macro was introduced to do a common
hardware timeout. The macro function triggers a counter of
retries or a timeout in us. However, in many cases, like in
nrfx_adc.c the timeout value is set to 0, leading to a infinite
loop in mp_hal_delay_us. This patch prevents this from happening.
Path of error:
nrfx_adc.c -> NRFX_WAIT_FOR -> NRFX_DELAY_US -> mp_hal_delay_us.
This patch also opens up for all arguments to be set as positional
arguments such that an external user of the make_new function can set
provide all parameters as positional arguments.
machine/i2c already uses mp_hal_get_pin_obj which
points to pin_find function in order to locate correct
pin object to use.
The pin_find function was recently updated to also
being able to locate pins based on an integer value,
such that pin number can be used as argument to object
constructors.
This patch modfies and uniforms pin object lookup for
SPI, music and pwm.
Renaming config for enabling random module with hw
random number generator from MICROPY_PY_HW_RNG to
MICROPY_PY_RANDOM_HW_RNG to indicate which module it
is configuring.
Also, disabling the config by default in mpconfigport.h.
Adding the enable of RNG in all board configs.
Moving ifdef in modrandom, which test for the config being
set, earlier in the code. This is to prevent un-necessary
includes if not needed.
Increase the maximum number of queued notifications from 1 to 6. This
massively speeds up the NUS console - especially when printing large
amounts of text. The reason is that multiple transfers can be done in a
single connection event, in ideal cases 6 at a time.
This patch moves all nrf52 targets to use SPIM backend
for SPI which features EasyDMA. The main benefit of doing
this is to utilize the SPIM3 on nrf52840 which is
EasyDMA only peripheral.
This patch ads irq method to the pin object. Handlers
registered in the irq method will be kept as part of the
ROOT_POINTERS.
In order to resolve which pin object is the root of the
IRQ, the pin_find has been extended to also be able to
search up Pin objects based on mp_int_t pin number.
This also implies that the Pin.new API is now also supporting
creation of Pin objects based on the integer value of the
pin instead of old style mandating string name of the Pin.
All boards have been updated to use real pin number from
0-48 instead of pin_Pxx for UART/SPI and music module pins.
UART/SPI/modmusic has also been updated to use pin number
provided directly or look up the Pin object based on the
integer value of the pin (modmusic).
Pin generation has been updated to create a list of pins, where
the board/cpu dicts are now refering to an index in this list
instead of having one const declaration for each pin. This new
const table makes it possible to iterate through all pins generated
in order to locate the correct Pin object.
In order to be able to support GPIO1 port on nrf52840
the port has been removed from the Pin object.
All pins on port1 will now be incrementally on top of
the pin numbers for gpio0. Hence, Pin 1.00 will become
P32, and Pin 1.15 will become P47.
The modification is done to address the new gpio HAL
interface in nrfx, which resolves the port to be
configured base on a multiple of 32.
The patch also affects the existing devices which does
not have a second GPIO port in the way that the
port indication A and B is removed from Pin generation.
This means that the port which was earlier addressed
as PA0 is now P0, and PA31 is P31.
Also, this patch removes the gpio member which earlier
pointed to the perihperal GPIO base address. This is not
needed anymore, hence removed.
With all the variation in chips and boards it's tedious to copy and
redefine linker scripts for every option. Making linker scripts more
modular also opens up more possibilities, like enabling/disabling the
flash file system from the Makefile - or even defining it's size from a
Makefile argument (FS_SIZE=12 for a 12kB filesystem if tight on space).
Summarized this squashed PR replaces the hal/ folder in the port. This has been replaced the official
HAL layer from Nordic Semiconductor; https://github.com/NordicSemiconductor/nrfx.
A Git submodule has been added under lib/nrfx, for the nrfx dependency.
The drivers / modules has been updated to use this new HAL layer; nrfx at v1.0.0.
Also, header files and system files for nrf51/nrf52x chip variants has been deleted from the device/ folder, only keeping back the startup files written in C. All other files are now fetched from nrfx.
3 new header files in the ports/nrf/ folder has been added to configure nrfx (nrfx_config.h), logging (nrfx_log.h) and glue nrfx together with the drivers and modules from micropython (nrfx_glue.h).
The PR has been a joint effort from @aykevl (Ayke van Laethem) and @glennrub.
For reference, the commit log will be kept to get an overview of the changes done:
* ports/nrf: Initial commit for moving hal to Nordic Semiconductor BSD-3 licensed nrfx-hal.
* ports/nrf: Adding nrfx, Nordic Semiconductor BSD-3 hal layer, as git submodule checked out at lib/nrfx.
* ports/nrf/modules/machine/uart: Fixing bug which set hwfc to parity excluded, always resulting in no flow control, hence corrupted output. Also adding an extra loop on uart_tx_char to prevent any tx when any ongoing tx is in progress.
* ports/nrf/i2c: Moving I2C over to nrfx driver.
* ports/nrf/modules/machine/i2c: Alignment. Renaming print function param 'o' to 'self_in'
* ports/nrf/spi: Updating SPI machine module to use nrfx drivers.
* ports/nrf: Renaming modules/machine/rtc.c/.h to rtcounter.c/.h to not confuse the peripheral with Real-Time Clock:
* ports/nrf: Updating various files after renaming machine module RTC to RTCounter.
* ports/nrf: Renaming RTC to RTCounter in modmachine globals dict table. Also updating object type name to reflect new module name.
* ports/nrf: Fixing leftovers after renaming rtc to rtcounter.
* ports/nrf: Early untested adoption of nrfx_rtc in RTCounter. Untested.
* nrf/modules/machine/i2c: Improve keyword argument handling
* ports/nrf/modules/temp: Updating Temp machine module to use nrfx defined hal nrf_temp.h. Moving logic of BLE stack awareness to machine module.
* ports/nrf/boards/pca10040: Enable machine Temp module.
* nrf/modules/machine/rtcounter: Remove magic constants.
* ports/nrf: Adding base support for nrfx module logging. Adding option to disable logging of UART as it might log its own setup over UART while the peripheral is not yet set up. Logging of UART could make sense if other transport of log is used.
* ports/nrf: updating nrfx_log.h with more correct parenthisis on macro grouping.
* ports/nrf: Updating nrfx logging with configuration to disable logging of UART module. The pattern can be used to turn off other modules as well. However, for now UART is the only module locking itself by logging before the peripheral is configured. Logging is turned off by default, can be enabled in nrfx_config.h by setting NRFX_LOG_ENABLED=1.
* ports/nrf/modules/random: Updating modrandom to use nrfx hal for rng. Not using nrfx-driver for this peripheral as its blocking mode would do the trick on RNG. Moving softdevice aware code from legacy hal to modrandom.c.
* nrf: Enable Peripheral Resource Sharing.
This enables TWI and SPI to be enabled at the same time.
* nrf/Makefile: Define MCU sub variant (e.g. NRF51822/NRF51422)
* nrf: Port TIMER peripheral to nrfx HAL.
* nrf/modules/machine/uart: Optimize UART module
For a nRF51, this results in a size reduction of:
.text: -68 bytes
.data: -56 bytes
* nrf/modules/machine/uart: Don't use magic index numbers.
* nrf/modules/machine/uart: Fix off-by-one error.
For nrf51:
.text: -40 bytes
* nrf/modules/machine/rtcounter: Update for nrfx HAL.
* nrf/modules/machine/i2c: Reduce RAM consumption.
Reductions for the nrf51:
flash: -108 bytes
RAM: -72 bytes
* nrf/mpconfigport: Avoid unnecessary root pointers.
This saves 92 bytes of RAM.
* nrf: Support SoftDevice with nrfx HAL.
* nrf: Add NVMC peripheral (microbitfs) support.
There is no support yet for a SoftDevice.
It also fixes a potentially serious bug in start_index generation.
* nrf/modules/machine/spi: Optimize SPI peripheral.
nrf51:
text: -340 bytes
data: -72 bytes
nrf52:
text: -352 bytes
data: -108 bytes
* nrf/modules/random: Forgot to commit header file.
* nrf: Make nrfx_config.h universal for all boards.
* nrf: Use SoftDevice API for flash access when built for SD
* nrf/drivers/bluetooth: Remove legacy HAL driver includes.
These were not used anymore so can be removed.
* ports/nrf/microbit: Port microbit targets to nrfx HAL
Initial port of microbit modules to use nrfx HAL layer.
Tested display/image and modmusic on micro:bit to verify that
softpwm and ticker for nrf51 is working as expected.
Changing IRQ priority on timer to priority 2, as 1 might collide if
used side by side of SD110 BLE stack.
The patch reserves Timer1 peripheral compile time. This is not ideal
and should be resolved in seperate task.
* nrf/boards/microbit: Remove custom nrfx_config.h from microbit target, adding disablement of timer1 if softpwm is enabled.
* nrf/adc: Update ADC module to use nrfx
* nrf/modules/machine/pwm: Updating machine PWM module to use nrfx HAL driver.
examples/nrf52_pwm.py and examples/nrf52_servo.py tested on pca10040.
* nrf: Removing hal folder and boards nrf5x_hal_conf.h headers.
* nrf/nrfx_glue: Adding direct NVIC access for S110 BLE stack
If SoftDevice s110 has not yet been initialized, the IRQ will not be forwarded to
the application using the sd_nvic* function calls. Hence, direct access to cmsi
nvic functions are used instead if SoftDevice is not enabled.
* nrf/drivers/ticker: Setting IRQ priority 3 on Timer1
SoftDevice fails to initilize if Timer1 has been configured to priority
level 2 before enabling the SD. The timer is set to priority 1, higher than BLE
stack in order to provide better quality of music rendering when used with the
music module. This might be too high, time will show.
* nrf/examples: Updating ubluepy_temp after moving RTCounter to nrfx.
* nrf: delete duplicate files from device folder which can be located in nrfx/mdk.
* nrf/Makefile: Fetch system files from nrfx.
Testing on each device sub-variant to figure out which system file to
use. Reason for this is that nrf52.c is actually defining nrf52832.
Removing NRF_DEFINES parameter setting the device in use into the
same sub-variant test, as NRF52 is unique to nrf52832 when using nrfx.
Without this exclusion of -DNRF52 in compilation for nrf52840, the
device will be interpreted as a nrf52, hence nrf52832.
Also, changing name on variable SRC_NRF_HAL to SRC_NRFX_HAL to
explicitly tell the origin of the file.
* nrf: Updating device #ifdefs to be more open to non-nrf51 targets.
* nrf/modules/machine/uart: Removing second instance of UART for nrf52840 as it only has one non-DMA variant.
* nrf/device: Removing system files as these are now used from nrfx/mdk
* nrf: Moving startup files in device one level up as there is no need for deep hierarchy.
* nrf: Use NRF52_SERIES defined in nrfx/mdk/nrf.h as define value when testing for both nrf52(832) and nrf52840 variants.
* nrf/modules/machine/uart: Enable UART RX by default
Enable rx by default after intiialization of the peripheral.
Else, the nrfx driver will re-enable rx for each byte read
on uart REPL, clearing the EVENT_RXDRDY before second byte,
which again will make second byte get lost and read will get stuck.
This happens if the bytes are transmitted nrf(51) while still
processing the previous byte. Not seen on nrf52, but should
also become an issue at higher speeds.
This patch sets rx to always be enabled. Hence, not clearing the event
between read bytes, and it will be able to detect next byte recieved
upon finishing the first.
* nrf/modules/machine/timer: Fixing defines excluding Timer1 if ticker/softpwm is used.
* nrf: Switching import form mpconfigboard.h to mpconfigport.h in nrfx_config.h as mpconfigboard.h might define default values for defines not set by board specific header.
* nrf/modules/machine/i2c: nrfx integration fixes
Increasing speed to 400K.
Returning Address NACK's as MP error code; MP_ENODEV.
Returning MP_ETIMEOUT on all other error codes from TWI nrfx driver
except the ANACK.
Enabling and disabling the TWI peripheral before and after each transaction.
* nrf/examples: Updating ssd1306_mod.py to split framebuffer transfer into multiple chunks
* nrf/modules/machine/i2c: Return MP_EIO error if Data NACK occurs.
* nrf: Addressing review comments.
* nrf: Updating git submodule and users to nrfx v1.0.0.
* nrf/modules/machine/adc: Update adc module to follow v1.0.0 nrfx API.
* nrf/modules/machine/spi: Implement init and deinit functions
Extending SPI objects with a config member such that
configuration can be kept between new() and init().
Moving initialization done in new() to common init
function shared between the module functions.
If SPI is already configured, the SPI peripheral will
be uninitialized before initalized again.
Adding logic to handle initialization of polarity and
phase. As well, updating default speed to 1M from 500K.
* nrf/modules/machine: Removing unused nrfx includes in machine module header files
When compiling for microbit with LTO=0, a compiler error occurs due to
'ms' variable in the microbit_sleep function has not been initialized.
This patch initialize the variable to 0.
