This generalises and simplifies the code and follows CPython behaviour.
See similar change for floats in a07fc5b640.
Signed-off-by: Damien George <damien@micropython.org>
This is possible now that MP_UNARY_OP_INT_MAYBE exists.
As a consequence mp_obj_get_int now also supports user types, which was
previously possible with MP_UNARY_OP_INT but no tests existed for it.
Signed-off-by: Damien George <damien@micropython.org>
To be consistent with MP_UNARY_OP_INT_FLOAT and MP_UNARY_OP_INT_COMPLEX,
and allow int() to first check if a type supports __int__ before trying
other things (as per CPython).
Signed-off-by: Damien George <damien@micropython.org>
MicroPython does not support these special methods, and they may get in the
way of other tests (eg indexing with __int__).
Signed-off-by: Damien George <damien@micropython.org>
This one sets the flash image length properly for the teensy loader, such
that the file system is not erased. It was already set in commit
8e54225140 but got lost when the MIMXRT1176
board was added.
Signed-off-by: robert-hh <robert@hammelrath.com>
Three bugs have been fixed in this commit:
1. When the duty was set with duty_u16(), changing the freq with pwm.freq()
would not keep relative duty rate, but the absolute pulse duration.
2. Fix another inconsistency when displaying the PWM pin's properties of a
QTMR channel.
3. Improve the error checks for the second channel being a PWM pin and pin
pairs to be a FLEXPWM A/B pair.
Signed-off-by: robert-hh <robert@hammelrath.com>
These have by default FAT support. The SAMD21 build does not support FAT.
The nrf port also implements os.sync(), but has it's own copy of moduos.c.
Code size increases seen: 40 to 56 bytes.
Signed-off-by: robert-hh <robert@hammelrath.com>
Avoiding code duplication. To enable it, set MICROPY_PY_UOS_SYNC in the
port's mpconfigport.h. It is operational only for FAT file system. For
other filesystems it's a no-op.
Signed-off-by: robert-hh <robert@hammelrath.com>
The hal_entry.c code is duplicated across all boards, so consolidate it to
a common ra_hal.c file. And remove the hal_entry() function because it
simply calls main().
Signed-off-by: Damien George <damien@micropython.org>
Also fix MAX_ENDPOINT definition for G0, which follows G4.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
By specifying rts=pin(x) and/or cts=Pin(x) in the constructor. The pad
numbers for the UART pins are fix in this case: TX must be at pad 0, RX at
pad 1, RTS at pad 2 and CTS at pad 3.
repr(uart) shows the pin names for rts and cts, if set. In case of a RX
overflow, the rx interrupt will be disabled instead of just discarding the
data. That allows RTS to act.
If RTS is inactive, still 2 bytes can be buffered in the FIFO.
Signed-off-by: robert-hh <robert@hammelrath.com>
With Crystal: set the crystal startup wait time to 1 second. It was 2
seconds before, and that seeemed too long.
With USB-Sync: scan for up to 1 second for the USB to be registered and
carry on with boot as soon as it it. Before, the code just waited for
500ms.
Side change: improve related comments.
Signed-off-by: robert-hh <robert@hammelrath.com>
These include ADC, DAC, I2C, SoftI2C, SPI, SoftI2C, PWM, UART, pulse. This
is useful for devices like the Adafruit Trinket series which have almost no
accessible GPIO pins.
Signed-off-by: robert-hh <robert@hammelrath.com>
If sockets were open when calling soft reset, gc_sweep_all() would try to
close them. In case of e.g. the NINA WiFi handler, connected through SPI,
spi_transfer() would be called for command exchange with the NINA module.
But at that time SerCom was already disabled.
Moving sercom_deinit_all() behind gc_sweep_all() solves this issue.
Signed-off-by: robert-hh <robert@hammelrath.com>
Such that they are easier to adapt. The maximum code size is set by:
MICROPY_HW_CODESIZE=xxxK
in mpconfigmcu.mk for the MCU family as default or in mpconfigboard.mk for
a specific board. Setting the maximum code size allows the loader to error
out if the code gets larger than the space dedicated for it.
Signed-off-by: robert-hh <robert@hammelrath.com>
This commit adds the "--escape-non-printable" option to the repl command.
When specified the REPL console will escape non-printable characters,
printing them as their hex value in square brackets.
This escaping behaviour was previously the default and only behaviour, but
it is now opt-in.
As part of this change, the speed of echoing device data to the console is
improved by by reading and writing in chunks.
Signed-off-by: Damien George <damien@micropython.org>
Change UART clock source on S3/C3 so the UART can operate when CPU
frequency is below 80MHz. This allows the UART to remain operational when
using Dynamic Frequency Scaling (DFS).
Signed-off-by: Patrick Joy <patrick@joytech.com.au>
This commit enables the ULP for the S2 and S3 chips.
Note this is the FSM (Finite State Machine) ULP.
Signed-off-by: Patrick Joy <patrick@joytech.com.au>
Once all the firmware has been flashed and the final signatures checked,
mboot writes the "all good" byte into the header of the application. This
step uses the buffer firmware_head which, if unaligned in the build, fails
when cast to a uint64_t* in flash.c.
Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au>
These were incorrectly added in d995c01042.
The fix here includes the full differential ADC definitions.
Signed-off-by: brave ulysses <brave_ulysses@email.com>
Update docs/library/espnow.rst to add:
- guidance on using WLAN.config(pm=WLAN.PM_NONE) for reliable
espnow performance while also connected to a wifi access point;
- guidance on receiving encrypted messages;
- correction for default value of "encrypt" parameter (add_peer());
- guidance on use of ESPNow.irq(): recommand users readout all messages
in the buffer each time the callback is called.
Signed-off-by: Glenn Moloney <glenn.moloney@gmail.com>
The code that handles inplace-operator to normal-binary-operator fallback
is moved in this commit from py/objtype.c to py/runtime.c, making it apply
to all types, not just user classes.
Signed-off-by: Damien George <damien@micropython.org>
