This changes the signatures of QSPI write_cmd_data, write_cmd_addr_data and
read_cmd_qaddr_qdata so they return an error code. The softqspi and stm32
hardware qspi driver are updated to follow this new signature. Also the
spiflash driver is updated to use these new return values.
Signed-off-by: Damien George <damien@micropython.org>
The STM32H7xx HAL LPUART AF macros are missing the number, this HAL is the
only one that's inconsistent in the way it defines LPUART AF macros, so we
only need to define them for H7.
Prior to this commit, only sector 0 was erase/write protected, which may
not be enough to protect all of mboot (especially if mboot lives at a
higher address than the start of flash).
This commit makes sure all internal flash sectors that mboot lives in are
protected from erasing and writing. The linker script must define
_mboot_writable_flash_start for this to work.
Signed-off-by: Damien George <damien@micropython.org>
For STM32L4, hardware I2C can be implemented by using TIMINGR.
This commit enables:
- Use of hardware I2C in machine.I2C.
- Specifying a frequency greater than or equal to 400KHz with pyb.I2C.
For STM32L4 series, the internal sensors are connected to:
- ADC1_IN0: Internal voltage reference
- ADC1_IN17: Temperature sensor
- ADC1_IN18: VBAT battery voltage monitoring
but ADC_CHANNEL_VREFINT, ADC_CHANNEL_VBAT, ADC_CHANNEL_TEMPSENSOR are not
defined as 0, 17, 18.
This commit converts channel 0, 17, 18 to ADC_CHANNEL_x in
adc_get_internal_channel().
Prior to this commit, the actual I2C frequency can be faster than specified
one and it may exceed the I2C's specification for Fast Mode. The frequency
of SCL should be less than or equal to 400KHz in Fast Mode.
This commit fixes this issue for F4 MCUs by rounding up the division in the
frequency calculation.
Excuting the code:
i2c = I2C(1, I2C.CONTROLLER, dma=True)
tmp = i2c.recv(1, i2c_addr)
recv_data = bytearray(56)
i2c.recv(recv_data, i2c_addr)
The second i2c.recv() fails with OSError: [Errno 110] ETIMEDOUT. When
receiving greater than or equal to 2 bytes at first i2c.recv(), the second
i2c.recv() succeeds. This issue does not occur without DMA.
Details of change: when executing I2C with DMA:
- Bit 11 of I2Cx_CR2 (DMA Request Enable) should be 1 to indicate that DMA
transfer is enabled. This bit is set after I2C event interrupt is
enabled in HAL_I2C_Master_Transmit_DMA()/HAL_I2C_Master_Receive_DMA(), so
DMA Request Enable bit might be 0 in IRQHandler.
- In case of data receive:
- When only 1 byte receiption, clear I2Cx_CR1's bit 10 (ACK).
- When only 2 byte receiption, clear I2Cx_CR1's bit 10 (ACK) and set
bit 11 (POS).
- When greater than or equal to 2 byte receiption, bit 12 of I2Cx_CR2
(DMA Last Transfer) should set to generate NACK when DMA transfer
completed.
Otherwise, the I2C bus may be busy after received data from peripheral.
A board can now name the CDC ports, eg:
#define MICROPY_HW_USB_CDC_NUM (3)
#define MICROPY_HW_USB_INTERFACE_CDC0_STRING "REPL"
#define MICROPY_HW_USB_INTERFACE_CDC1_STRING "GDB Server"
#define MICROPY_HW_USB_INTERFACE_CDC2_STRING "UART Port"
Signed-off-by: Damien George <damien@micropython.org>
Seems unused outside of spi.c, spi_obj[] array is the expected way to
iterate these.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This is necessary to access sites that only support these protocols.
The rp2 port already has ECDH enabled, so this just adds ECDSA there. The
other ports now gain both ECDH and ECDSA. The code size increase is:
- rp2 (PICO_W): +2916 bytes flash, +24 bytes BSS
- stm32 (PYBD_SF6): +20480 bytes flash, +32 bytes data, +48 bytes BSS
- mimxrt (TEENSY41): +20708 bytes flash, +32 bytes data, +48 bytes BSS
- unix (standard x86-64): +39344 executable, +1744 bytes data, +96 BSS
This is obviously a large increase in code size. But there doesn't seem to
be any other option because without elliptic curve cryptography devices are
partially cut off from the internet. For use cases that require small
firmware size, they'll need to build custom firmware with a custom mbedtls
config.
Signed-off-by: Damien George <damien@micropython.org>
The following multi-tests pass (eg with PYBD_SF6+LEGO_HUB_NO6):
ble_gap_advertise.py
ble_gap_connect.py
ble_gap_device_name.py
ble_gattc_discover_services.py
ble_gatt_data_transfer.py
perf_gatt_char_write.py
perf_gatt_notify.py
stress_log_filesystem.py
These are the same tests that passed prior to this BTstack update.
Also tested on the unix port using H4 transport.
Signed-off-by: Damien George <damien@micropython.org>
This makes it so that all a port needs to do is set the relevant variables
and "include extmod.mk" and doesn't need to worry about adding anything to
OBJ, CFLAGS, SRC_QSTR, etc.
Make all extmod variables (src, flags, etc) private to extmod.mk.
Also move common/shared, extmod-related fragments (e.g. wiznet, cyw43,
bluetooth) into extmod.mk.
Now that SRC_MOD, CFLAGS_MOD, CXXFLAGS_MOD are unused by both extmod.mk
(and user-C-modules in a previous commit), remove all uses of them from
port makefiles.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This applies to nimble, btstack, axtls, mbedtls, lwip.
Rather than having the ports individually manage GIT_SUBMODULES for these
components, make extmod.mk append them when the relevant feature is
enabled.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Removes the need for the port to add anything to OBJS or SRC_QSTR.
Also makes it possible for user-C-modules to differentiate between code
that should be processed for QSTR vs other files (e.g. helpers and
libraries).
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Instead of being an explicit field, it's now a slot like all the other
methods.
This is a marginal code size improvement because most types have a make_new
(100/138 on PYBV11), however it improves consistency in how types are
declared, removing the special case for make_new.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The goal here is to remove a slot (making way to turn make_new into a slot)
as well as reduce code size by the ~40 references to mp_identity_getiter
and mp_stream_unbuffered_iter.
This introduces two new type flags:
- MP_TYPE_FLAG_ITER_IS_ITERNEXT: This means that the "iter" slot in the
type is "iternext", and should use the identity getiter.
- MP_TYPE_FLAG_ITER_IS_CUSTOM: This means that the "iter" slot is a pointer
to a mp_getiter_iternext_custom_t instance, which then defines both
getiter and iternext.
And a third flag that is the OR of both, MP_TYPE_FLAG_ITER_IS_STREAM: This
means that the type should use the identity getiter, and
mp_stream_unbuffered_iter as iternext.
Finally, MP_TYPE_FLAG_ITER_IS_GETITER is defined as a no-op flag to give
the default case where "iter" is "getiter".
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Since L4 HAL version 1.17.0, HAL_TIM_IC_Start_IT() checks whether specified
channel of timer is busy or not, which is the case if this function is
called more than once without first calling HAL_TIM_IC_Stop_IT(). The fix
in this commit is to call the stop function before calling start. The PWM
and OC modes have the same issue with the same fix.
Fixes issue #8732.
Prior to this commit, excuting this code:
i2c = I2C(1, I2C.CONTROLLER, dma=True)
i2c.send(data, addr=i2c_addr)
the call to i2c.send() does not return and the board needs a reset. This
code works when dma=False.
According to the specification, I2Cx_EV_IRQHandler should:
- Write DR to address when Start condition generated.
- Clear ADDR by reading SR2 after reading SR2 when address sent.
These processes are included in HAL_I2C_EV_IRQHandler(), however the
firmware size increses about 2KB if HAL_I2C_EV_IRQHandler is called. This
commit adds above processes to i2c_ev_irq_handler, and increases firmware
by less than 100 bytes.
Fixes issue #2643.
pyb.ADC(channel) checks whether specified channel is valid or have ADC
capability but pyb.ADCAll().read_channel() does not.
This change adds checking whether specified channel is valid and throw
ValueError if channel is invalid. This is same as pyb.ADC().
Although this driver and associated hardware can be used on any board, it
makes to only freeze it for PYB and PYBD boards. It can be easily copied
to any board if needed.
Fixes issue #8056.
Signed-off-by: Damien George <damien@micropython.org>
Changes in this commit:
- Manifest include's now use the directory path where possible (no longer
necessary to include the manifest.py file explicitly).
- Add manifest.py for all drivers and components that are referenced by
port/board manifests.
- Replace all uses of freeze() with package()/module(), except for port and
board modules.
- Use opt=3 everywhere, for consistency and to reduce code size.
- Use require() instead of include() for all micropython-lib references.
- Remove support for optional board-level manifest.py in mimxrt port, to
make it behave the same as other ports (the board must set
FROZEN_MANIFEST to a custom manifest.py, which can optionally include the
default, port-level manifest).
- Also reinstates modules that were accidentally removed from the esp8266
512k build in fbe9417b90.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Signed-off-by: Damien George <damien@micropython.org>
Since uart.write() of the STM32 port waits until all bytes have
been sent, uart.flush() and uart.txdone() are implemented as empty
functions to provide API consistency.
uart.flush()
flush() will always return immediately.
ret = uart.txdone()
uart.txdone() will always return True.
Previously the desired output type was specified. Now make the type part
of the function name. Because this function is used in a few places this
saves code size due to smaller call-site.
This makes `mp_obj_new_str_type_from_vstr` a private function of objstr.c
(which is almost the only place where the output type isn't a compile-time
constant).
This saves ~140 bytes on PYBV11.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
It has been about 8 years since support for this chip was added. Reasons
to remove it are:
- It is no longer easy to obtain this part.
- There are now many other options for WiFi.
- It's not a good use of developer time to maintain it.
Signed-off-by: Damien George <damien@micropython.org>
Not safe to use mp_hal_delay_ms before boot if threading is enabled,
because threading will not have been initialised, and
MICROPY_EVENT_POLL_HOOK assumes threading is initialised.
HAL_Delay doesn't call MICROPY_EVENT_POLL_HOOK, but is still
power-efficient like mp_hal_delay_ms (unlike mp_hal_delay_us).
Fixes#7816.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Rather than having the autobuild know about the particular variants, have
the mpconfigboard.mk describe them and make autobuild discover them
automatically.
Adds a "query-variants" target to stm32/Makefile to allow the set of
possible variants to be queried.
Removes pybv3 from the autobuild as this isn't use by the downloads page.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
If mboot is built with support for packing (signing/encryption) it needs up
to 32KiB. So for simplicity increase the mboot region to 32KiB
unconditionally for WB55 boards (custom WB55 board configurations can still
provide their own linker scripts to override this).
Since commit e65d1e69e8 there is no longer an
io.FileIO class, so this option is no longer needed.
This option also controlled whether or not files supported being opened in
binary mode (eg 'rb'), and could, if disabled, lead to confusion as to why
opening a file in binary mode silently did the wrong thing (it would just
open in text mode if MICROPY_PY_IO_FILEIO was disabled).
The various VFS implementations (POSIX, FAT, LFS) were the only places
where enabling this option made a difference, and in almost all cases where
one of these filesystems were enabled, MICROPY_PY_IO_FILEIO was also
enabled. So it makes sense to just unconditionally enable this feature
(ability to open a file in binary mode) in all cases, and so just remove
this config option altogether. That makes configuration simpler and means
binary file support always exists (and opening a file in binary mode is
arguably more fundamental than opening in text mode, so if anything should
be configurable then it should be the ability to open in text mode).
Signed-off-by: Damien George <damien@micropython.org>
It seems sometimes gcc with LTO will generate otherwise valid assembly
listings that cause 'as' to error out when generating DWARF debug info; see
https://sourceware.org/bugzilla/show_bug.cgi?id=29494
Therefore, don't enable -g by default if LTO is on.
Enabling LTO=1 DEBUG=1 is still possible but may result in random errors
at link time due to 'as' (the error in this case is "Error: unaligned
opcodes detected in executable segment", and the only other easy workaround
is CFLAGS+=-fno-jump-tables which may increase code size significantly).
Follows on from fdfe4eca74
In-the-field use of these FUS/WS firmware update scripts has exposed some
weak points, causing corrupted FUS/WS firmware to be flashed to the unit.
The problems are mostly caused with the ST GUI application, but sometimes
from un-recognised failures during bin file transfer to the WB55 prior to
running the rfcore_firmware.py script. Other failures were caused by
incorrect load addresses being used, again both from user error copying the
address from the HTML release notes to the GUI tool, but also from
similarly not updating the address correctly in rfcore_firmware.py
To guard against these errors and make it easier to prepare different
versions, this commit adds a few features to the rfcore firmware update
tools:
- When creating the bin file, automatically parse the release note in the
folder to get the correct address.
- Add a footer to the bin file containing the name, version, CRC, address
etc.
- Before flashing rfcore, check if the same version is already installed.
- Verify the CRC and obfuscation key before flashing bin.
- Log the name and version of file being flashed.
This adds support for the LEGO Hub No. 7, aka LEGO Technic Small hub, aka
LEGO SPIKE Essential hub. This board is largely similar to Hub No. 6:
- Same MCU (STM32F413 - different packaging with fewer pins).
- Same Bluetooth chip (TI CC2564).
- Same IMU chip.
- Similar external flash chip - 4MiB instead of 32MiB.
- 2 I/O ports instead of 6.
- No display - only status and battery LEDs.
- Different LED driver chip.
- Only 1 button which is also the power button.
- No speaker.
Signed-off-by: David Lechner <david@pybricks.com>
This adds configurable macros to define the timer and channel used to
provide the Bluetooth 32768 MHz clock. This will allow code to be shared
with LEGO_HUB_NO7.
Signed-off-by: David Lechner <david@pybricks.com>
This changes spiflash.py to read the flash chip ID at runtime to select the
read/write/erase commands. This will allow the code to be shared with
LEGO_HUB_NO7 which doesn't use the 32-bit commands.
Also remove an unused constant while we are touching this.
Signed-off-by: David Lechner <david@pybricks.com>
This changes appupdate.py to get the filesystem size at runtime. This will
allow the code to be shared with LEGO_HUB_NO7 which has a similar flash
chip with a different size.
Signed-off-by: David Lechner <david@pybricks.com>
This changes all uses of pins to use the alias names of the pins. This
makes the code easier to understand and will also allow sharing more code
with LEGO_HUB_NO7.
Signed-off-by: David Lechner <david@pybricks.com>
For bare metal ARM & xtensa targets, passing -g will make the ELF file
larger but doesn't change the binary size. However, this means tools like
gdb, addr2line, etc can extract source-level information from the ELF.
Also standardise -ggdb to -g, these produce the exact same ELF file on
arm-none-eabi-gcc and will use DWARF format for all these ports.
Fixes:
- Should read `definitions` rather than `defintions`.
- Should read `resolution` rather than `resoultion`.
- Should read `inefficient` rather than `inefficent`.
- Should read `closed` rather than `closded`.
Signed-off-by: Tim Gates <tim.gates@iress.com>
All ports that use mbedtls use the custom error messages in
mp_mbedtls_errors.c. This commit simplifies the build so that ports don't
need to explicitly add this file, it's now used by default when mbedtls is
enabled.
Signed-off-by: Damien George <damien@micropython.org>
All in-tree uses of MICROPY_PORT_ROOT_POINTERS have been replaced with
MP_REGISTER_ROOT_POINTER(), so now we can remove both
MICROPY_PORT_ROOT_POINTERS and MICROPY_BOARD_ROOT_POINTERS from the code
and remaining config files.
Signed-off-by: David Lechner <david@pybricks.com>
This uses MP_REGISTER_ROOT_POINTER() to register mod_network_nic_list and
removes the same from all mpconfigport.h.
Signed-off-by: David Lechner <david@pybricks.com>
This uses MP_REGISTER_ROOT_POINTER() to register bluetooth_nimble_memory
and bluetooth_nimble_root_pointers and removes the same from all
mpconfigport.h.
Signed-off-by: David Lechner <david@pybricks.com>
This uses MP_REGISTER_ROOT_POINTER() to register
bluetooth_btstack_root_pointers and removes the same from all
mpconfigport.h.
Signed-off-by: David Lechner <david@pybricks.com>
This uses MP_REGISTER_ROOT_POINTER() to register the readline_history root
pointer array used by shared/readline.c and removes the registration from
all mpconfigport.h files.
This also required adding a new MICROPY_READLINE_HISTORY_SIZE config option
since not all ports used the same sized array.
Signed-off-by: David Lechner <david@pybricks.com>
This adds new compile-time infrastructure to parse source code files for
`MP_REGISTER_ROOT_POINTER()` and generates a new `root_pointers.h` header
file containing the collected declarations. This works the same as the
existing `MP_REGISTER_MODULE()` feature.
Signed-off-by: David Lechner <david@pybricks.com>
To override it a board must define MICROPY_BOARD_FATAL_ERROR to a function
that takes a string message and does not return.
Signed-off-by: Damien George <damien@micropython.org>
Commit 9670a156da missed one renaming of
MICROPY_PY_WIZNET5K to MICROPY_PY_NETWORK_WIZNET5K which prevented the
Wiznet interface from being enabled.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
When tested, this reduces default MP binary sizes by approx 2-2.5%, and
very marginally increases performance in benchmarks. Build times seem very
similar to non-LTO when using gcc 12.
See #8733 for further discussion.
Signed-off-by: Angus Gratton <gus@projectgus.com>
Prerequisite for enabling Link Time Optimisation.
The _bl_state address is the same as _estack, but _estack is referred to as
a uint32_t elsewhere in the code. LTO doesn't like it when the same symbol
has two different types.
Signed-off-by: Angus Gratton <gus@projectgus.com>
This separates extmod source files from `py.mk`. Previously, `py.mk`
assumed that every consumer of the py/ directory also wanted to include
extmod/. However, this is not the case. For example, building mpy-cross
uses py/ but doesn't need extmod/.
This commit moves all extmod-specific items from `py.mk` to `extmod.mk` and
explicitly includes `extmod.mk` in ports that use it.
Signed-off-by: David Lechner <david@pybricks.com>
Both led_init and led_state are configurable via MBOOT_BOARD_LED_INIT and
MBOOT_BOARD_LED_STATE respectively, so don't need to be MP_WEAK.
Furthermore, led_state and led0_state are private to ui.c so can be made
static.
Signed-off-by: Damien George <damien@micropython.org>
System config block contains hardware unrelated to USB. So calling
`__SYSCFG_CLK_DISABLE()` during `HAL_PCD_MspDeInit()` has an adverse effect
on other system functionality.
Removing call to `__SYSCFG_CLK_DISABLE()` to rectify this issue.
This call was there since the beginning of the USB CDC code, added in
b30c02afa0.
According to ST Errata ES0206 Rev 18, Section 2.2.1, on STM32F427x,
STM32F437x, STM32F429x and STM32F439x.
If the system tick interrupt is enabled during stop mode while certain
bits are set in the DBGMCU_CR, then the system will immediately wake
from stop mode.
Suggested workaround is to disable system tick timer interrupt when
entering stop mode.
According to ST Errate ES0394 Rev 11, Section 2.2.17, on STM32WB55Cx and
STM32WB35Cx.
If the system tick interrupt is enabled during stop 0, stop 1 or stop 2
while certain bits are set in DBGMCU_CR, then system will immediately
wake from stop mode but the system remains in low power state. The CPU
therefore fetches incorrect data from inactive Flash, which can cause a
hard fault.
Suggested workaround is to disable system tick timer interrupt when
entering stop mode.
This was added by mistake in 8f68e26f79 when
adding support for G4 MCUs, which does not using this get_bank() function.
FLASH_OPTR_DBANK is only defined on G4 and L4 MCUs, so on H7 this
FLASH_BANK_2 code was being wrongly excluded.
Signed-off-by: Damien George <damien@micropython.org>
It's no longer needed because this macro is now processed after
preprocessing the source code via cpp (in the qstr extraction stage), which
means unused MP_REGISTER_MODULE's are filtered out by the preprocessor.
Signed-off-by: Damien George <damien@micropython.org>
The following changes are made:
- Use software SPI for external SPI flash access when building mboot.
- Enable the mboot filesystem-loading feature, with FAT FS support.
- Increase the frequency of the CPU when in mboot to 96MHz, to increase the
speed of SPI flash accesses and programming.
Signed-off-by: Damien George <damien@micropython.org>
This allows a board to modify initial_r0 if needed.
Also make default board behaviour functions always available, named as
mboot_get_reset_mode_default and mboot_state_change_default.
Signed-off-by: Damien George <damien@micropython.org>
For ports with MICROPY_VFS and MICROPY_PY_IO enabled their configuration
can now be simplified to use the defaults for mp_import_stat and
mp_builtin_open.
This commit makes no functional change, except for the following minor
points:
- the built-in "open" is removed from the minimal port (it previously did
nothing)
- the duplicate built-in "input" is removed from the esp32 port
- qemu-arm now delegates to VFS import/open
Signed-off-by: Damien George <damien@micropython.org>
This reverts commit 2668337f36.
The issue with potential breaking of the BLE RX path in the radio is fixed
since WS v1.12.0.
Signed-off-by: Damien George <damien@micropython.org>
This replaces occurences of
foo_t *foo = m_new_obj(foo_t);
foo->base.type = &foo_type;
with
foo_t *foo = mp_obj_malloc(foo_t, &foo_type);
Excludes any places where base is a sub-field or when new0/memset is used.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit adds a board definition for NUCLEO_G0B1RE. This board has the
REPL on UART2 which is connected to the on-board ST-link USB-UART.
Signed-off-by: Asensio Lorenzo Sempere <asensio.aerospace@gmail.com>
This implements self-triggering of the Flash NVIC interrupt on Cortex-M0
devices, which allows enabling internal storage on those MCUs.
Signed-off-by: Asensio Lorenzo Sempere <asensio.aerospace@gmail.com>
These files that are reformatted only now fall under the list of files to
apply uncrustify/black formatting to.
Signed-off-by: Damien George <damien@micropython.org>
To avoid any I/O glitches in mp_hal_pin_config, make sure a valid alternate
function is set in AFR first before switching the pin mode. When switching
from AF to INPUT or OUTPUT, the AF in AFR will remain valid up until the
pin mode is switched.
- Add board-level configuration option to set the SMPS supply mode.
- Wait for valid voltage levels after configuring the SMPS mode.
- Wait for external supply ready flag if SMPS supplies external circuitry.
All user interface (LED, button) code has been moved to ui.c, and the
interface to this code with the rest of the system now goes through calls
to mboot_state_change(). This state-change function can be overridden by a
board to fully customise the user interface behaviour.
Signed-off-by: Damien George <damien@micropython.org>
This is enabled at MICROPY_CONFIG_ROM_LEVEL_EXTRA_FEATURES, which is the
default for stm32. Not setting the value in mpconfigboard.h allows boards
to optionally configure it.
Signed-off-by: Damien George <damien@micropython.org>
