micropython/ports/stm32/boards/VCC_GND_H743VI/mpconfigboard.h

104 lines
3.7 KiB
C

/* This file is part of the MicroPython project, http://micropython.org/
* MIT License; Copyright (c) 2021 Damien P. George
*/
// STM32H743VIT6 H7 core board by VCC-GND Studio
// http://vcc-gnd.com/
// https://item.taobao.com/item.htm?ft=t&id=614466740679
// https://www.aliexpress.com/wholesale?SearchText=STM32H743VIT6
#define MICROPY_HW_BOARD_NAME "VCC-GND STM32H743VI"
#define MICROPY_HW_MCU_NAME "STM32H743VI"
#define MICROPY_HW_FLASH_FS_LABEL "VCCGNDH743VI"
#define MICROPY_HW_ENABLE_RTC (1)
#define MICROPY_HW_ENABLE_RNG (1)
#define MICROPY_HW_ENABLE_ADC (1)
#define MICROPY_HW_ENABLE_DAC (1)
#define MICROPY_HW_ENABLE_USB (1)
#define MICROPY_HW_ENABLE_SDCARD (1)
#define MICROPY_HW_HAS_SWITCH (1)
#define MICROPY_HW_HAS_FLASH (1)
#define MICROPY_BOARD_EARLY_INIT VCC_GND_STM32H743VI_board_early_init
// The board has an 25MHz HSE, the following gives 480MHz CPU speed
#define MICROPY_HW_CLK_PLLM (5)
#define MICROPY_HW_CLK_PLLN (192)
#define MICROPY_HW_CLK_PLLP (2)
#define MICROPY_HW_CLK_PLLQ (4)
#define MICROPY_HW_CLK_PLLR (2)
// The USB clock is set using PLL3
#define MICROPY_HW_CLK_PLL3M (5)
#define MICROPY_HW_CLK_PLL3N (48)
#define MICROPY_HW_CLK_PLL3P (2)
#define MICROPY_HW_CLK_PLL3Q (5)
#define MICROPY_HW_CLK_PLL3R (2)
// 5 wait states
#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_5
// UART config
#define MICROPY_HW_UART2_TX (pin_D5)
#define MICROPY_HW_UART2_RX (pin_D6)
#define MICROPY_HW_UART2_RTS (pin_D4)
#define MICROPY_HW_UART2_CTS (pin_D3)
#define MICROPY_HW_UART3_TX (pin_D8)
#define MICROPY_HW_UART3_RX (pin_D9)
#define MICROPY_HW_UART5_TX (pin_B6)
#define MICROPY_HW_UART5_RX (pin_B12)
#define MICROPY_HW_UART6_TX (pin_C6)
#define MICROPY_HW_UART6_RX (pin_C7)
#define MICROPY_HW_UART8_TX (pin_E1)
#define MICROPY_HW_UART8_RX (pin_E0)
// I2C buses
#define MICROPY_HW_I2C1_SCL (pin_B6)
#define MICROPY_HW_I2C1_SDA (pin_B7)
#define MICROPY_HW_I2C2_SCL (pin_B10)
#define MICROPY_HW_I2C2_SDA (pin_B11)
#define MICROPY_HW_I2C3_SCL (pin_A8)
#define MICROPY_HW_I2C3_SDA (pin_C9)
// SPI buses
#define MICROPY_HW_SPI1_NSS (pin_A4)
#define MICROPY_HW_SPI1_SCK (pin_A5)
#define MICROPY_HW_SPI1_MISO (pin_A6)
#define MICROPY_HW_SPI1_MOSI (pin_A7)
#define MICROPY_HW_SPI2_NSS (pin_B12)
#define MICROPY_HW_SPI2_SCK (pin_B13)
#define MICROPY_HW_SPI2_MISO (pin_B14)
#define MICROPY_HW_SPI2_MOSI (pin_B15)
// USRSW is pulled low. Pressing the button makes the input go high.
#define MICROPY_HW_USRSW_PIN (pin_B3)
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
#define MICROPY_HW_USRSW_PRESSED (1)
// LEDs
#define MICROPY_HW_LED1 (pin_A13) // red
#define MICROPY_HW_LED2 (pin_A14) // green
#define MICROPY_HW_LED3 (pin_A15) // yellow
#define MICROPY_HW_LED4 (pin_B4) // blue
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
// USB config
#define MICROPY_HW_USB_FS (1)
#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10)
// FDCAN bus
#define MICROPY_HW_CAN1_NAME "FDCAN1"
#define MICROPY_HW_CAN1_TX (pin_D1)
#define MICROPY_HW_CAN1_RX (pin_D0)
// SD card detect switch
#define MICROPY_HW_SDCARD_DETECT_PIN (pin_A8)
#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP)
#define MICROPY_HW_SDCARD_DETECT_PRESENT (GPIO_PIN_RESET)
void VCC_GND_STM32H743VI_board_early_init(void);