mirror of
https://github.com/licsber/micropython.git
synced 2024-09-21 09:30:24 +08:00
f7c4f9a640
Previously, SPI was configured by a board defining MICROPY_HW_ENABLE_SPIx to 0 or 1. Now, the board should define MICROPY_HW_SPIx_SCK, MISO, MOSI and NSS. This makes it the same as how I2C is configured.
71 lines
2.6 KiB
C
71 lines
2.6 KiB
C
#define NETDUINO_PLUS_2
|
|
|
|
#define MICROPY_HW_BOARD_NAME "NetduinoPlus2"
|
|
#define MICROPY_HW_MCU_NAME "STM32F405RG"
|
|
|
|
#define MICROPY_HW_HAS_SWITCH (1)
|
|
|
|
// On the netuino, the sdcard appears to be wired up as a 1-bit
|
|
// SPI, so the driver needs to be converted to support that before
|
|
// we can turn this on.
|
|
#define MICROPY_HW_HAS_SDCARD (0)
|
|
#define MICROPY_HW_HAS_MMA7660 (0)
|
|
#define MICROPY_HW_HAS_LIS3DSH (0)
|
|
#define MICROPY_HW_HAS_LCD (0)
|
|
#define MICROPY_HW_ENABLE_RNG (1)
|
|
#define MICROPY_HW_ENABLE_RTC (0)
|
|
#define MICROPY_HW_ENABLE_TIMER (1)
|
|
#define MICROPY_HW_ENABLE_SERVO (1)
|
|
#define MICROPY_HW_ENABLE_DAC (0)
|
|
#define MICROPY_HW_ENABLE_CAN (0)
|
|
|
|
// HSE is 25MHz
|
|
#define MICROPY_HW_CLK_PLLM (25)
|
|
#define MICROPY_HW_CLK_PLLN (336)
|
|
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
|
|
#define MICROPY_HW_CLK_PLLQ (7)
|
|
|
|
// UART config
|
|
#define MICROPY_HW_UART1_PORT (GPIOA)
|
|
#define MICROPY_HW_UART1_PINS (GPIO_PIN_9 | GPIO_PIN_10)
|
|
#define MICROPY_HW_UART2_PORT (GPIOA)
|
|
#define MICROPY_HW_UART2_PINS (GPIO_PIN_2 | GPIO_PIN_3)
|
|
#define MICROPY_HW_UART2_RTS (GPIO_PIN_1)
|
|
#define MICROPY_HW_UART2_CTS (GPIO_PIN_0)
|
|
#define MICROPY_HW_UART3_PORT (GPIOD)
|
|
#define MICROPY_HW_UART3_PINS (GPIO_PIN_8 | GPIO_PIN_9)
|
|
#define MICROPY_HW_UART3_RTS (GPIO_PIN_12)
|
|
#define MICROPY_HW_UART3_CTS (GPIO_PIN_11)
|
|
#define MICROPY_HW_UART4_PORT (GPIOA)
|
|
#define MICROPY_HW_UART4_PINS (GPIO_PIN_0 | GPIO_PIN_1)
|
|
#define MICROPY_HW_UART6_PORT (GPIOC)
|
|
#define MICROPY_HW_UART6_PINS (GPIO_PIN_6 | GPIO_PIN_7)
|
|
|
|
// I2C busses
|
|
#define MICROPY_HW_I2C2_SCL (pin_B10)
|
|
#define MICROPY_HW_I2C2_SDA (pin_B11)
|
|
|
|
// SPI busses
|
|
#define MICROPY_HW_SPI2_NSS (pin_B12)
|
|
#define MICROPY_HW_SPI2_SCK (pin_B13)
|
|
#define MICROPY_HW_SPI2_MISO (pin_B14)
|
|
#define MICROPY_HW_SPI2_MOSI (pin_B15)
|
|
|
|
// USRSW is pulled low. Pressing the button makes the input go high.
|
|
#define MICROPY_HW_USRSW_PIN (pin_B11)
|
|
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
|
|
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
|
|
#define MICROPY_HW_USRSW_PRESSED (1)
|
|
|
|
// LEDs
|
|
#define MICROPY_HW_LED1 (pin_A10) // Blue LED
|
|
#define MICROPY_HW_LED2 (pin_C13) // White LED (aka Power)
|
|
#define MICROPY_HW_LED3 (pin_A10) // Same as Led(1)
|
|
#define MICROPY_HW_LED4 (pin_C13) // Same as Led(2)
|
|
#define MICROPY_HW_LED_OTYPE (GPIO_MODE_OUTPUT_PP)
|
|
#define MICROPY_HW_LED_ON(pin) (pin->gpio->BSRRL = pin->pin_mask)
|
|
#define MICROPY_HW_LED_OFF(pin) (pin->gpio->BSRRH = pin->pin_mask)
|
|
|
|
// USB VBUS detect pin
|
|
#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
|