micropython/docs/esp32/quickref.rst

498 lines
17 KiB
ReStructuredText

.. _esp32_quickref:
Quick reference for the ESP32
=============================
.. image:: img/esp32.jpg
:alt: ESP32 board
:width: 640px
The Espressif ESP32 Development Board (image attribution: Adafruit).
Below is a quick reference for ESP32-based boards. If it is your first time
working with this board it may be useful to get an overview of the microcontroller:
.. toctree::
:maxdepth: 1
general.rst
tutorial/intro.rst
Installing MicroPython
----------------------
See the corresponding section of tutorial: :ref:`esp32_intro`. It also includes
a troubleshooting subsection.
General board control
---------------------
The MicroPython REPL is on UART0 (GPIO1=TX, GPIO3=RX) at baudrate 115200.
Tab-completion is useful to find out what methods an object has.
Paste mode (ctrl-E) is useful to paste a large slab of Python code into
the REPL.
The :mod:`machine` module::
import machine
machine.freq() # get the current frequency of the CPU
machine.freq(240000000) # set the CPU frequency to 240 MHz
The :mod:`esp` module::
import esp
esp.osdebug(None) # turn off vendor O/S debugging messages
esp.osdebug(0) # redirect vendor O/S debugging messages to UART(0)
# low level methods to interact with flash storage
esp.flash_size()
esp.flash_user_start()
esp.flash_erase(sector_no)
esp.flash_write(byte_offset, buffer)
esp.flash_read(byte_offset, buffer)
The :mod:`esp32` module::
import esp32
esp32.hall_sensor() # read the internal hall sensor
esp32.raw_temperature() # read the internal temperature of the MCU, in Farenheit
esp32.ULP() # access to the Ultra-Low-Power Co-processor
Note that the temperature sensor in the ESP32 will typically read higher than
ambient due to the IC getting warm while it runs. This effect can be minimised
by reading the temperature sensor immediately after waking up from sleep.
Networking
----------
The :mod:`network` module::
import network
wlan = network.WLAN(network.STA_IF) # create station interface
wlan.active(True) # activate the interface
wlan.scan() # scan for access points
wlan.isconnected() # check if the station is connected to an AP
wlan.connect('essid', 'password') # connect to an AP
wlan.config('mac') # get the interface's MAC adddress
wlan.ifconfig() # get the interface's IP/netmask/gw/DNS addresses
ap = network.WLAN(network.AP_IF) # create access-point interface
ap.config(essid='ESP-AP') # set the ESSID of the access point
ap.active(True) # activate the interface
A useful function for connecting to your local WiFi network is::
def do_connect():
import network
wlan = network.WLAN(network.STA_IF)
wlan.active(True)
if not wlan.isconnected():
print('connecting to network...')
wlan.connect('essid', 'password')
while not wlan.isconnected():
pass
print('network config:', wlan.ifconfig())
Once the network is established the :mod:`socket <usocket>` module can be used
to create and use TCP/UDP sockets as usual, and the ``urequests`` module for
convenient HTTP requests.
Delay and timing
----------------
Use the :mod:`time <utime>` module::
import time
time.sleep(1) # sleep for 1 second
time.sleep_ms(500) # sleep for 500 milliseconds
time.sleep_us(10) # sleep for 10 microseconds
start = time.ticks_ms() # get millisecond counter
delta = time.ticks_diff(time.ticks_ms(), start) # compute time difference
Timers
------
Virtual (RTOS-based) timers are supported. Use the :ref:`machine.Timer <machine.Timer>` class
with timer ID of -1::
from machine import Timer
tim = Timer(-1)
tim.init(period=5000, mode=Timer.ONE_SHOT, callback=lambda t:print(1))
tim.init(period=2000, mode=Timer.PERIODIC, callback=lambda t:print(2))
The period is in milliseconds.
.. _Pins_and_GPIO:
Pins and GPIO
-------------
Use the :ref:`machine.Pin <machine.Pin>` class::
from machine import Pin
p0 = Pin(0, Pin.OUT) # create output pin on GPIO0
p0.on() # set pin to "on" (high) level
p0.off() # set pin to "off" (low) level
p0.value(1) # set pin to on/high
p2 = Pin(2, Pin.IN) # create input pin on GPIO2
print(p2.value()) # get value, 0 or 1
p4 = Pin(4, Pin.IN, Pin.PULL_UP) # enable internal pull-up resistor
p5 = Pin(5, Pin.OUT, value=1) # set pin high on creation
Available Pins are from the following ranges (inclusive): 0-19, 21-23, 25-27, 32-39.
These correspond to the actual GPIO pin numbers of ESP32 chip. Note that many
end-user boards use their own adhoc pin numbering (marked e.g. D0, D1, ...).
For mapping between board logical pins and physical chip pins consult your board
documentation.
Notes:
* Pins 1 and 3 are REPL UART TX and RX respectively
* Pins 6, 7, 8, 11, 16, and 17 are used for connecting the embedded flash,
and are not recommended for other uses
* Pins 34-39 are input only, and also do not have internal pull-up resistors
* The pull value of some pins can be set to ``Pin.PULL_HOLD`` to reduce power
consumption during deepsleep.
PWM (pulse width modulation)
----------------------------
PWM can be enabled on all output-enabled pins. The base frequency can
range from 1Hz to 40MHz but there is a tradeoff; as the base frequency
*increases* the duty resolution *decreases*. See
`LED Control <https://docs.espressif.com/projects/esp-idf/en/latest/api-reference/peripherals/ledc.html>`_
for more details.
Use the ``machine.PWM`` class::
from machine import Pin, PWM
pwm0 = PWM(Pin(0)) # create PWM object from a pin
pwm0.freq() # get current frequency
pwm0.freq(1000) # set frequency
pwm0.duty() # get current duty cycle
pwm0.duty(200) # set duty cycle
pwm0.deinit() # turn off PWM on the pin
pwm2 = PWM(Pin(2), freq=20000, duty=512) # create and configure in one go
ADC (analog to digital conversion)
----------------------------------
On the ESP32 ADC functionality is available on Pins 32-39. Note that, when
using the default configuration, input voltages on the ADC pin must be between
0.0v and 1.0v (anything above 1.0v will just read as 4095). Attenuation must
be applied in order to increase this usable voltage range.
Use the :ref:`machine.ADC <machine.ADC>` class::
from machine import ADC
adc = ADC(Pin(32)) # create ADC object on ADC pin
adc.read() # read value, 0-4095 across voltage range 0.0v - 1.0v
adc.atten(ADC.ATTN_11DB) # set 11dB input attentuation (voltage range roughly 0.0v - 3.6v)
adc.width(ADC.WIDTH_9BIT) # set 9 bit return values (returned range 0-511)
adc.read() # read value using the newly configured attenuation and width
ESP32 specific ADC class method reference:
.. method:: ADC.atten(attenuation)
This method allows for the setting of the amount of attenuation on the
input of the ADC. This allows for a wider possible input voltage range,
at the cost of accuracy (the same number of bits now represents a wider
range). The possible attenuation options are:
- ``ADC.ATTN_0DB``: 0dB attenuation, gives a maximum input voltage
of 1.00v - this is the default configuration
- ``ADC.ATTN_2_5DB``: 2.5dB attenuation, gives a maximum input voltage
of approximately 1.34v
- ``ADC.ATTN_6DB``: 6dB attenuation, gives a maximum input voltage
of approximately 2.00v
- ``ADC.ATTN_11DB``: 11dB attenuation, gives a maximum input voltage
of approximately 3.6v
.. Warning::
Despite 11dB attenuation allowing for up to a 3.6v range, note that the
absolute maximum voltage rating for the input pins is 3.6v, and so going
near this boundary may be damaging to the IC!
.. method:: ADC.width(width)
This method allows for the setting of the number of bits to be utilised
and returned during ADC reads. Possible width options are:
- ``ADC.WIDTH_9BIT``: 9 bit data
- ``ADC.WIDTH_10BIT``: 10 bit data
- ``ADC.WIDTH_11BIT``: 11 bit data
- ``ADC.WIDTH_12BIT``: 12 bit data - this is the default configuration
Software SPI bus
----------------
There are two SPI drivers. One is implemented in software (bit-banging)
and works on all pins, and is accessed via the :ref:`machine.SPI <machine.SPI>`
class::
from machine import Pin, SPI
# construct an SPI bus on the given pins
# polarity is the idle state of SCK
# phase=0 means sample on the first edge of SCK, phase=1 means the second
spi = SPI(baudrate=100000, polarity=1, phase=0, sck=Pin(0), mosi=Pin(2), miso=Pin(4))
spi.init(baudrate=200000) # set the baudrate
spi.read(10) # read 10 bytes on MISO
spi.read(10, 0xff) # read 10 bytes while outputing 0xff on MOSI
buf = bytearray(50) # create a buffer
spi.readinto(buf) # read into the given buffer (reads 50 bytes in this case)
spi.readinto(buf, 0xff) # read into the given buffer and output 0xff on MOSI
spi.write(b'12345') # write 5 bytes on MOSI
buf = bytearray(4) # create a buffer
spi.write_readinto(b'1234', buf) # write to MOSI and read from MISO into the buffer
spi.write_readinto(buf, buf) # write buf to MOSI and read MISO back into buf
.. Warning::
Currently *all* of ``sck``, ``mosi`` and ``miso`` *must* be specified when
initialising Software SPI.
Hardware SPI bus
----------------
There are two hardware SPI channels that allow faster transmission
rates (up to 80Mhz). These may be used on any IO pins that support the
required direction and are otherwise unused (see :ref:`Pins_and_GPIO`)
but if they are not configured to their default pins then they need to
pass through an extra layer of GPIO multiplexing, which can impact
their reliability at high speeds. Hardware SPI channels are limited
to 40MHz when used on pins other than the default ones listed below.
===== =========== ============
\ HSPI (id=1) VSPI (id=2)
===== =========== ============
sck 14 18
mosi 13 23
miso 12 19
===== =========== ============
Hardware SPI has the same methods as Software SPI above::
from machine import Pin, SPI
hspi = SPI(1, 10000000, sck=Pin(14), mosi=Pin(13), miso=Pin(12))
vspi = SPI(2, baudrate=80000000, polarity=0, phase=0, bits=8, firstbit=0, sck=Pin(18), mosi=Pin(23), miso=Pin(19))
I2C bus
-------
The I2C driver is implemented in software and works on all pins,
and is accessed via the :ref:`machine.I2C <machine.I2C>` class::
from machine import Pin, I2C
# construct an I2C bus
i2c = I2C(scl=Pin(5), sda=Pin(4), freq=100000)
i2c.readfrom(0x3a, 4) # read 4 bytes from slave device with address 0x3a
i2c.writeto(0x3a, '12') # write '12' to slave device with address 0x3a
buf = bytearray(10) # create a buffer with 10 bytes
i2c.writeto(0x3a, buf) # write the given buffer to the slave
Real time clock (RTC)
---------------------
See :ref:`machine.RTC <machine.RTC>` ::
from machine import RTC
rtc = RTC()
rtc.datetime((2017, 8, 23, 1, 12, 48, 0, 0)) # set a specific date and time
rtc.datetime() # get date and time
Deep-sleep mode
---------------
The following code can be used to sleep, wake and check the reset cause::
import machine
# check if the device woke from a deep sleep
if machine.reset_cause() == machine.DEEPSLEEP_RESET:
print('woke from a deep sleep')
# put the device to sleep for 10 seconds
machine.deepsleep(10000)
Notes:
* Calling ``deepsleep()`` without an argument will put the device to sleep
indefinitely
* A software reset does not change the reset cause
* There may be some leakage current flowing through enabled internal pullups.
To further reduce power consumption it is possible to disable the internal pullups::
p1 = Pin(4, Pin.IN, Pin.PULL_HOLD)
After leaving deepsleep it may be necessary to un-hold the pin explicitly (e.g. if
it is an output pin) via::
p1 = Pin(4, Pin.OUT, None)
OneWire driver
--------------
The OneWire driver is implemented in software and works on all pins::
from machine import Pin
import onewire
ow = onewire.OneWire(Pin(12)) # create a OneWire bus on GPIO12
ow.scan() # return a list of devices on the bus
ow.reset() # reset the bus
ow.readbyte() # read a byte
ow.writebyte(0x12) # write a byte on the bus
ow.write('123') # write bytes on the bus
ow.select_rom(b'12345678') # select a specific device by its ROM code
There is a specific driver for DS18S20 and DS18B20 devices::
import time, ds18x20
ds = ds18x20.DS18X20(ow)
roms = ds.scan()
ds.convert_temp()
time.sleep_ms(750)
for rom in roms:
print(ds.read_temp(rom))
Be sure to put a 4.7k pull-up resistor on the data line. Note that
the ``convert_temp()`` method must be called each time you want to
sample the temperature.
NeoPixel driver
---------------
Use the ``neopixel`` module::
from machine import Pin
from neopixel import NeoPixel
pin = Pin(0, Pin.OUT) # set GPIO0 to output to drive NeoPixels
np = NeoPixel(pin, 8) # create NeoPixel driver on GPIO0 for 8 pixels
np[0] = (255, 255, 255) # set the first pixel to white
np.write() # write data to all pixels
r, g, b = np[0] # get first pixel colour
For low-level driving of a NeoPixel::
import esp
esp.neopixel_write(pin, grb_buf, is800khz)
.. Warning::
By default ``NeoPixel`` is configured to control the more popular *800kHz*
units. It is possible to use alternative timing to control other (typically
400kHz) devices by passing ``timing=0`` when constructing the
``NeoPixel`` object.
Capacitive Touch
----------------
Use the ``TouchPad`` class in the ``machine`` module::
from machine import TouchPad, Pin
t = TouchPad(Pin(14))
t.read() # Returns a smaller number when touched
``TouchPad.read`` returns a value relative to the capacitive variation. Small numbers (typically in
the *tens*) are common when a pin is touched, larger numbers (above *one thousand*) when
no touch is present. However the values are *relative* and can vary depending on the board
and surrounding composition so some calibration may be required.
There are ten capacitive touch-enabled pins that can be used on the ESP32: 0, 2, 4, 12, 13
14, 15, 27, 32, 33. Trying to assign to any other pins will result in a ``ValueError``.
Note that TouchPads can be used to wake an ESP32 from sleep::
import machine
from machine import TouchPad, Pin
import esp32
t = TouchPad(Pin(14))
t.config(500) # configure the threshold at which the pin is considered touched
esp32.wake_on_touch(True)
machine.lightsleep() # put the MCU to sleep until a touchpad is touched
For more details on touchpads refer to `Espressif Touch Sensor
<https://docs.espressif.com/projects/esp-idf/en/latest/api-reference/peripherals/touch_pad.html>`_.
DHT driver
----------
The DHT driver is implemented in software and works on all pins::
import dht
import machine
d = dht.DHT11(machine.Pin(4))
d.measure()
d.temperature() # eg. 23 (°C)
d.humidity() # eg. 41 (% RH)
d = dht.DHT22(machine.Pin(4))
d.measure()
d.temperature() # eg. 23.6 (°C)
d.humidity() # eg. 41.3 (% RH)
WebREPL (web browser interactive prompt)
----------------------------------------
WebREPL (REPL over WebSockets, accessible via a web browser) is an
experimental feature available in ESP32 port. Download web client
from https://github.com/micropython/webrepl (hosted version available
at http://micropython.org/webrepl), and configure it by executing::
import webrepl_setup
and following on-screen instructions. After reboot, it will be available
for connection. If you disabled automatic start-up on boot, you may
run configured daemon on demand using::
import webrepl
webrepl.start()
# or, start with a specific password
webrepl.start(password='mypass')
The WebREPL daemon listens on all active interfaces, which can be STA or
AP. This allows you to connect to the ESP32 via a router (the STA
interface) or directly when connected to its access point.
In addition to terminal/command prompt access, WebREPL also has provision
for file transfer (both upload and download). The web client has buttons for
the corresponding functions, or you can use the command-line client
``webrepl_cli.py`` from the repository above.
See the MicroPython forum for other community-supported alternatives
to transfer files to an ESP32 board.