micropython/stm/stmusb/usb_hcd.c

266 lines
5.9 KiB
C

/**
******************************************************************************
* @file usb_hcd.c
* @author MCD Application Team
* @version V2.1.0
* @date 19-March-2012
* @brief Host Interface Layer
******************************************************************************
* @attention
*
* <h2><center>&copy; COPYRIGHT 2012 STMicroelectronics</center></h2>
*
* Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
* You may not use this file except in compliance with the License.
* You may obtain a copy of the License at:
*
* http://www.st.com/software_license_agreement_liberty_v2
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "usb_core.h"
#include "usb_hcd.h"
#include "usb_conf.h"
#include "usb_bsp.h"
#ifdef USE_HOST_MODE
/** @addtogroup USB_OTG_DRIVER
* @{
*/
/** @defgroup USB_HCD
* @brief This file is the interface between EFSL ans Host mass-storage class
* @{
*/
/** @defgroup USB_HCD_Private_Defines
* @{
*/
/**
* @}
*/
/** @defgroup USB_HCD_Private_TypesDefinitions
* @{
*/
/**
* @}
*/
/** @defgroup USB_HCD_Private_Macros
* @{
*/
/**
* @}
*/
/** @defgroup USB_HCD_Private_Variables
* @{
*/
/**
* @}
*/
/** @defgroup USB_HCD_Private_FunctionPrototypes
* @{
*/
/**
* @}
*/
/** @defgroup USB_HCD_Private_Functions
* @{
*/
/**
* @brief HCD_Init
* Initialize the HOST portion of the driver.
* @param pdev: Selected device
* @param base_address: OTG base address
* @retval Status
*/
uint32_t HCD_Init(USB_OTG_CORE_HANDLE *pdev ,
USB_OTG_CORE_ID_TypeDef coreID)
{
uint8_t i = 0;
pdev->host.ConnSts = 0;
for (i= 0; i< USB_OTG_MAX_TX_FIFOS; i++)
{
pdev->host.ErrCnt[i] = 0;
pdev->host.XferCnt[i] = 0;
pdev->host.HC_Status[i] = HC_IDLE;
}
pdev->host.hc[0].max_packet = 8;
USB_OTG_SelectCore(pdev, coreID);
#ifndef DUAL_ROLE_MODE_ENABLED
USB_OTG_DisableGlobalInt(pdev);
USB_OTG_CoreInit(pdev);
/* Force Host Mode*/
USB_OTG_SetCurrentMode(pdev , HOST_MODE);
USB_OTG_CoreInitHost(pdev);
USB_OTG_EnableGlobalInt(pdev);
#endif
return 0;
}
/**
* @brief HCD_GetCurrentSpeed
* Get Current device Speed.
* @param pdev : Selected device
* @retval Status
*/
uint32_t HCD_GetCurrentSpeed (USB_OTG_CORE_HANDLE *pdev)
{
USB_OTG_HPRT0_TypeDef HPRT0;
HPRT0.d32 = USB_OTG_READ_REG32(pdev->regs.HPRT0);
return HPRT0.b.prtspd;
}
/**
* @brief HCD_ResetPort
* Issues the reset command to device
* @param pdev : Selected device
* @retval Status
*/
uint32_t HCD_ResetPort(USB_OTG_CORE_HANDLE *pdev)
{
/*
Before starting to drive a USB reset, the application waits for the OTG
interrupt triggered by the debounce done bit (DBCDNE bit in OTG_FS_GOTGINT),
which indicates that the bus is stable again after the electrical debounce
caused by the attachment of a pull-up resistor on DP (FS) or DM (LS).
*/
USB_OTG_ResetPort(pdev);
return 0;
}
/**
* @brief HCD_IsDeviceConnected
* Check if the device is connected.
* @param pdev : Selected device
* @retval Device connection status. 1 -> connected and 0 -> disconnected
*
*/
uint32_t HCD_IsDeviceConnected(USB_OTG_CORE_HANDLE *pdev)
{
return (pdev->host.ConnSts);
}
/**
* @brief HCD_GetCurrentFrame
* This function returns the frame number for sof packet
* @param pdev : Selected device
* @retval Frame number
*
*/
uint32_t HCD_GetCurrentFrame (USB_OTG_CORE_HANDLE *pdev)
{
return (USB_OTG_READ_REG32(&pdev->regs.HREGS->HFNUM) & 0xFFFF) ;
}
/**
* @brief HCD_GetURB_State
* This function returns the last URBstate
* @param pdev: Selected device
* @retval URB_STATE
*
*/
URB_STATE HCD_GetURB_State (USB_OTG_CORE_HANDLE *pdev , uint8_t ch_num)
{
return pdev->host.URB_State[ch_num] ;
}
/**
* @brief HCD_GetXferCnt
* This function returns the last URBstate
* @param pdev: Selected device
* @retval No. of data bytes transferred
*
*/
uint32_t HCD_GetXferCnt (USB_OTG_CORE_HANDLE *pdev, uint8_t ch_num)
{
return pdev->host.XferCnt[ch_num] ;
}
/**
* @brief HCD_GetHCState
* This function returns the HC Status
* @param pdev: Selected device
* @retval HC_STATUS
*
*/
HC_STATUS HCD_GetHCState (USB_OTG_CORE_HANDLE *pdev , uint8_t ch_num)
{
return pdev->host.HC_Status[ch_num] ;
}
/**
* @brief HCD_HC_Init
* This function prepare a HC and start a transfer
* @param pdev: Selected device
* @param hc_num: Channel number
* @retval status
*/
uint32_t HCD_HC_Init (USB_OTG_CORE_HANDLE *pdev , uint8_t hc_num)
{
return USB_OTG_HC_Init(pdev, hc_num);
}
/**
* @brief HCD_SubmitRequest
* This function prepare a HC and start a transfer
* @param pdev: Selected device
* @param hc_num: Channel number
* @retval status
*/
uint32_t HCD_SubmitRequest (USB_OTG_CORE_HANDLE *pdev , uint8_t hc_num)
{
pdev->host.URB_State[hc_num] = URB_IDLE;
pdev->host.hc[hc_num].xfer_count = 0 ;
return USB_OTG_HC_StartXfer(pdev, hc_num);
}
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
#endif // USE_HOST_MODE
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/