micropython/ports/stm32/boards/STM32F769DISC/mpconfigboard.h

167 lines
6.9 KiB
C

// This board is confirmed to operate using stlink and openocd.
// REPL is on UART(1) and is available through the stlink USB-UART device.
// To use openocd run "OPENOCD_CONFIG=boards/openocd_stm32f7.cfg" in
// the make command.
#define MICROPY_HW_BOARD_NAME "F769DISC"
#define MICROPY_HW_MCU_NAME "STM32F769"
#define MICROPY_HW_HAS_SWITCH (1)
#define MICROPY_HW_HAS_FLASH (1)
#define MICROPY_HW_HAS_SDCARD (1)
#define MICROPY_HW_ENABLE_RNG (1)
#define MICROPY_HW_ENABLE_RTC (1)
#define MICROPY_HW_ENABLE_USB (1)
// HSE is 25MHz
// VCOClock = HSE * PLLN / PLLM = 25 MHz * 432 / 25 = 432 MHz
// SYSCLK = VCOClock / PLLP = 432 MHz / 2 = 216 MHz
// USB/SDMMC/RNG Clock = VCOClock / PLLQ = 432 MHz / 9 = 48 MHz
#define MICROPY_HW_CLK_PLLM (25)
#define MICROPY_HW_CLK_PLLN (432)
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
#define MICROPY_HW_CLK_PLLQ (9)
#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_7 // 210-216 MHz needs 7 wait states
// UART config
#define MICROPY_HW_UART1_TX (pin_A9)
#define MICROPY_HW_UART1_RX (pin_A10)
#define MICROPY_HW_UART5_TX (pin_C12)
#define MICROPY_HW_UART5_RX (pin_D2)
#define MICROPY_HW_UART_REPL PYB_UART_1
#define MICROPY_HW_UART_REPL_BAUD 115200
// I2C busses
#define MICROPY_HW_I2C1_SCL (pin_B8)
#define MICROPY_HW_I2C1_SDA (pin_B9)
#define MICROPY_HW_I2C3_SCL (pin_H7)
#define MICROPY_HW_I2C3_SDA (pin_H8)
// SPI
#define MICROPY_HW_SPI2_NSS (pin_A11)
#define MICROPY_HW_SPI2_SCK (pin_A12)
#define MICROPY_HW_SPI2_MISO (pin_B14)
#define MICROPY_HW_SPI2_MOSI (pin_B15)
// CAN busses
#define MICROPY_HW_CAN1_TX (pin_B9)
#define MICROPY_HW_CAN1_RX (pin_B8)
#define MICROPY_HW_CAN2_TX (pin_B13)
#define MICROPY_HW_CAN2_RX (pin_B12)
// USRSW is pulled low. Pressing the button makes the input go high.
#define MICROPY_HW_USRSW_PIN (pin_A0)
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
#define MICROPY_HW_USRSW_PRESSED (1)
// LEDs
#define MICROPY_HW_LED1 (pin_J13) // red
#define MICROPY_HW_LED2 (pin_J5) // green
#define MICROPY_HW_LED3 (pin_A12) // green
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
// SD card detect switch
#define MICROPY_HW_SDMMC2_CK (pin_D6)
#define MICROPY_HW_SDMMC2_CMD (pin_D7)
#define MICROPY_HW_SDMMC2_D0 (pin_G9)
#define MICROPY_HW_SDMMC2_D1 (pin_G10)
#define MICROPY_HW_SDMMC2_D2 (pin_B3)
#define MICROPY_HW_SDMMC2_D3 (pin_B4)
#define MICROPY_HW_SDCARD_DETECT_PIN (pin_I15)
#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP)
#define MICROPY_HW_SDCARD_DETECT_PRESENT (GPIO_PIN_RESET)
// USB config (CN15 - USB OTG HS with external PHY)
#define MICROPY_HW_USB_HS (1)
#if 0
// Optional SDRAM configuration; requires SYSCLK <= 200MHz
#define MICROPY_HW_SDRAM_SIZE (128 * 1024 * 1024 / 8) // 128 Mbit
#define MICROPY_HW_SDRAM_STARTUP_TEST (0)
#define MICROPY_HEAP_START sdram_start()
#define MICROPY_HEAP_END sdram_end()
// Timing configuration for 90 Mhz (11.90ns) of SD clock frequency (180Mhz/2)
#define MICROPY_HW_SDRAM_TIMING_TMRD (2)
#define MICROPY_HW_SDRAM_TIMING_TXSR (7)
#define MICROPY_HW_SDRAM_TIMING_TRAS (4)
#define MICROPY_HW_SDRAM_TIMING_TRC (7)
#define MICROPY_HW_SDRAM_TIMING_TWR (2)
#define MICROPY_HW_SDRAM_TIMING_TRP (2)
#define MICROPY_HW_SDRAM_TIMING_TRCD (2)
#define MICROPY_HW_SDRAM_REFRESH_RATE (64) // ms
#define MICROPY_HW_SDRAM_BURST_LENGTH 1
#define MICROPY_HW_SDRAM_CAS_LATENCY 2
#define MICROPY_HW_SDRAM_COLUMN_BITS_NUM 8
#define MICROPY_HW_SDRAM_ROW_BITS_NUM 13
#define MICROPY_HW_SDRAM_MEM_BUS_WIDTH 32
#define MICROPY_HW_SDRAM_INTERN_BANKS_NUM 4
#define MICROPY_HW_SDRAM_CLOCK_PERIOD 2
#define MICROPY_HW_SDRAM_RPIPE_DELAY 0
#define MICROPY_HW_SDRAM_RBURST (1)
#define MICROPY_HW_SDRAM_WRITE_PROTECTION (0)
#define MICROPY_HW_SDRAM_AUTOREFRESH_NUM (8)
// See pins.csv for CPU pin mapping
#define MICROPY_HW_FMC_SDCKE0 (pyb_pin_FMC_SDCKE0)
#define MICROPY_HW_FMC_SDNE0 (pyb_pin_FMC_SDNE0)
#define MICROPY_HW_FMC_SDCLK (pyb_pin_FMC_SDCLK)
#define MICROPY_HW_FMC_SDNCAS (pyb_pin_FMC_SDNCAS)
#define MICROPY_HW_FMC_SDNRAS (pyb_pin_FMC_SDNRAS)
#define MICROPY_HW_FMC_SDNWE (pyb_pin_FMC_SDNWE)
#define MICROPY_HW_FMC_BA0 (pyb_pin_FMC_BA0)
#define MICROPY_HW_FMC_BA1 (pyb_pin_FMC_BA1)
#define MICROPY_HW_FMC_NBL0 (pyb_pin_FMC_NBL0)
#define MICROPY_HW_FMC_NBL1 (pyb_pin_FMC_NBL1)
#define MICROPY_HW_FMC_NBL2 (pyb_pin_FMC_NBL2)
#define MICROPY_HW_FMC_NBL3 (pyb_pin_FMC_NBL3)
#define MICROPY_HW_FMC_A0 (pyb_pin_FMC_A0)
#define MICROPY_HW_FMC_A1 (pyb_pin_FMC_A1)
#define MICROPY_HW_FMC_A2 (pyb_pin_FMC_A2)
#define MICROPY_HW_FMC_A3 (pyb_pin_FMC_A3)
#define MICROPY_HW_FMC_A4 (pyb_pin_FMC_A4)
#define MICROPY_HW_FMC_A5 (pyb_pin_FMC_A5)
#define MICROPY_HW_FMC_A6 (pyb_pin_FMC_A6)
#define MICROPY_HW_FMC_A7 (pyb_pin_FMC_A7)
#define MICROPY_HW_FMC_A8 (pyb_pin_FMC_A8)
#define MICROPY_HW_FMC_A9 (pyb_pin_FMC_A9)
#define MICROPY_HW_FMC_A10 (pyb_pin_FMC_A10)
#define MICROPY_HW_FMC_A11 (pyb_pin_FMC_A11)
#define MICROPY_HW_FMC_A12 (pyb_pin_FMC_A12)
#define MICROPY_HW_FMC_D0 (pyb_pin_FMC_D0)
#define MICROPY_HW_FMC_D1 (pyb_pin_FMC_D1)
#define MICROPY_HW_FMC_D2 (pyb_pin_FMC_D2)
#define MICROPY_HW_FMC_D3 (pyb_pin_FMC_D3)
#define MICROPY_HW_FMC_D4 (pyb_pin_FMC_D4)
#define MICROPY_HW_FMC_D5 (pyb_pin_FMC_D5)
#define MICROPY_HW_FMC_D6 (pyb_pin_FMC_D6)
#define MICROPY_HW_FMC_D7 (pyb_pin_FMC_D7)
#define MICROPY_HW_FMC_D8 (pyb_pin_FMC_D8)
#define MICROPY_HW_FMC_D9 (pyb_pin_FMC_D9)
#define MICROPY_HW_FMC_D10 (pyb_pin_FMC_D10)
#define MICROPY_HW_FMC_D11 (pyb_pin_FMC_D11)
#define MICROPY_HW_FMC_D12 (pyb_pin_FMC_D12)
#define MICROPY_HW_FMC_D13 (pyb_pin_FMC_D13)
#define MICROPY_HW_FMC_D14 (pyb_pin_FMC_D14)
#define MICROPY_HW_FMC_D15 (pyb_pin_FMC_D15)
#define MICROPY_HW_FMC_D16 (pyb_pin_FMC_D16)
#define MICROPY_HW_FMC_D17 (pyb_pin_FMC_D17)
#define MICROPY_HW_FMC_D18 (pyb_pin_FMC_D18)
#define MICROPY_HW_FMC_D19 (pyb_pin_FMC_D19)
#define MICROPY_HW_FMC_D20 (pyb_pin_FMC_D20)
#define MICROPY_HW_FMC_D21 (pyb_pin_FMC_D21)
#define MICROPY_HW_FMC_D22 (pyb_pin_FMC_D22)
#define MICROPY_HW_FMC_D23 (pyb_pin_FMC_D23)
#define MICROPY_HW_FMC_D24 (pyb_pin_FMC_D24)
#define MICROPY_HW_FMC_D25 (pyb_pin_FMC_D25)
#define MICROPY_HW_FMC_D26 (pyb_pin_FMC_D26)
#define MICROPY_HW_FMC_D27 (pyb_pin_FMC_D27)
#define MICROPY_HW_FMC_D28 (pyb_pin_FMC_D28)
#define MICROPY_HW_FMC_D29 (pyb_pin_FMC_D29)
#define MICROPY_HW_FMC_D30 (pyb_pin_FMC_D30)
#define MICROPY_HW_FMC_D31 (pyb_pin_FMC_D31)
#endif