micropython/ports/stm32/boards/NUCLEO_H743ZI/mpconfigboard.h

104 lines
3.6 KiB
C

#define MICROPY_HW_BOARD_NAME "NUCLEO_H743ZI"
#define MICROPY_HW_MCU_NAME "STM32H743"
#define MICROPY_HW_ENABLE_RTC (1)
#define MICROPY_HW_ENABLE_RNG (1)
#define MICROPY_HW_ENABLE_ADC (1)
#define MICROPY_HW_ENABLE_DAC (1)
#define MICROPY_HW_ENABLE_USB (1)
#define MICROPY_HW_ENABLE_SDCARD (1)
#define MICROPY_HW_HAS_SWITCH (1)
#define MICROPY_HW_HAS_FLASH (1)
#define MICROPY_BOARD_EARLY_INIT NUCLEO_H743ZI_board_early_init
void NUCLEO_H743ZI_board_early_init(void);
// The board has an 8MHz HSE, the following gives 400MHz CPU speed
#define MICROPY_HW_CLK_PLLM (4)
#define MICROPY_HW_CLK_PLLN (400)
#define MICROPY_HW_CLK_PLLP (2)
#define MICROPY_HW_CLK_PLLQ (4)
#define MICROPY_HW_CLK_PLLR (2)
// The USB clock is set using PLL3
#define MICROPY_HW_CLK_PLL3M (4)
#define MICROPY_HW_CLK_PLL3N (120)
#define MICROPY_HW_CLK_PLL3P (2)
#define MICROPY_HW_CLK_PLL3Q (5)
#define MICROPY_HW_CLK_PLL3R (2)
// 4 wait states
#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_4
// UART config
#define MICROPY_HW_UART2_TX (pin_D5)
#define MICROPY_HW_UART2_RX (pin_D6)
#define MICROPY_HW_UART2_RTS (pin_D4)
#define MICROPY_HW_UART2_CTS (pin_D3)
#define MICROPY_HW_UART3_TX (pin_D8)
#define MICROPY_HW_UART3_RX (pin_D9)
#define MICROPY_HW_UART5_TX (pin_B6)
#define MICROPY_HW_UART5_RX (pin_B12)
#define MICROPY_HW_UART6_TX (pin_C6)
#define MICROPY_HW_UART6_RX (pin_C7)
#define MICROPY_HW_UART7_TX (pin_F7)
#define MICROPY_HW_UART7_RX (pin_F6)
#define MICROPY_HW_UART8_TX (pin_E1)
#define MICROPY_HW_UART8_RX (pin_E0)
#define MICROPY_HW_UART_REPL PYB_UART_3
#define MICROPY_HW_UART_REPL_BAUD 115200
// I2C busses
#define MICROPY_HW_I2C1_SCL (pin_B8)
#define MICROPY_HW_I2C1_SDA (pin_B9)
#define MICROPY_HW_I2C2_SCL (pin_F1)
#define MICROPY_HW_I2C2_SDA (pin_F0)
#define MICROPY_HW_I2C4_SCL (pin_F14)
#define MICROPY_HW_I2C4_SDA (pin_F15)
// SPI
#define MICROPY_HW_SPI3_NSS (pin_A4)
#define MICROPY_HW_SPI3_SCK (pin_B3)
#define MICROPY_HW_SPI3_MISO (pin_B4)
#define MICROPY_HW_SPI3_MOSI (pin_B5)
// USRSW is pulled low. Pressing the button makes the input go high.
#define MICROPY_HW_USRSW_PIN (pin_C13)
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
#define MICROPY_HW_USRSW_PRESSED (1)
// LEDs
#define MICROPY_HW_LED1 (pin_B0) // green
#define MICROPY_HW_LED2 (pin_B7) // blue
#define MICROPY_HW_LED3 (pin_B14) // red
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
// USB config
#define MICROPY_HW_USB_FS (1)
#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10)
// FDCAN bus
#define MICROPY_HW_CAN1_NAME "FDCAN1"
#define MICROPY_HW_CAN1_TX (pin_D1)
#define MICROPY_HW_CAN1_RX (pin_D0)
// SD card detect switch
#define MICROPY_HW_SDCARD_DETECT_PIN (pin_G2)
#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP)
#define MICROPY_HW_SDCARD_DETECT_PRESENT (GPIO_PIN_RESET)
// Ethernet via RMII
#define MICROPY_HW_ETH_MDC (pin_C1)
#define MICROPY_HW_ETH_MDIO (pin_A2)
#define MICROPY_HW_ETH_RMII_REF_CLK (pin_A1)
#define MICROPY_HW_ETH_RMII_CRS_DV (pin_A7)
#define MICROPY_HW_ETH_RMII_RXD0 (pin_C4)
#define MICROPY_HW_ETH_RMII_RXD1 (pin_C5)
#define MICROPY_HW_ETH_RMII_TX_EN (pin_G11)
#define MICROPY_HW_ETH_RMII_TXD0 (pin_G13)
#define MICROPY_HW_ETH_RMII_TXD1 (pin_B13)