mirror of
https://github.com/licsber/micropython.git
synced 2024-09-21 01:20:23 +08:00
8f4c108025
Since commit e65d1e69e8 there is no longer an
io.FileIO class, so this option is no longer needed.
This option also controlled whether or not files supported being opened in
binary mode (eg 'rb'), and could, if disabled, lead to confusion as to why
opening a file in binary mode silently did the wrong thing (it would just
open in text mode if MICROPY_PY_IO_FILEIO was disabled).
The various VFS implementations (POSIX, FAT, LFS) were the only places
where enabling this option made a difference, and in almost all cases where
one of these filesystems were enabled, MICROPY_PY_IO_FILEIO was also
enabled. So it makes sense to just unconditionally enable this feature
(ability to open a file in binary mode) in all cases, and so just remove
this config option altogether. That makes configuration simpler and means
binary file support always exists (and opening a file in binary mode is
arguably more fundamental than opening in text mode, so if anything should
be configurable then it should be the ability to open in text mode).
Signed-off-by: Damien George <damien@micropython.org>
73 lines
2.6 KiB
C
73 lines
2.6 KiB
C
/* This file is part of the MicroPython project, http://micropython.org/
|
|
* MIT License; Copyright (c) 2019 Damien P. George
|
|
*/
|
|
|
|
#define MICROPY_HW_BOARD_NAME "B-L072Z-LRWAN1"
|
|
#define MICROPY_HW_MCU_NAME "STM32L072CZ"
|
|
|
|
#define MICROPY_EMIT_THUMB (0)
|
|
#define MICROPY_EMIT_INLINE_THUMB (0)
|
|
#define MICROPY_OPT_COMPUTED_GOTO (0)
|
|
#define MICROPY_PY_BUILTINS_COMPLEX (0)
|
|
#define MICROPY_PY_GENERATOR_PEND_THROW (0)
|
|
#define MICROPY_PY_MATH (0)
|
|
#define MICROPY_PY_FRAMEBUF (0)
|
|
#define MICROPY_PY_USOCKET (0)
|
|
#define MICROPY_PY_NETWORK (0)
|
|
#define MICROPY_PY_ONEWIRE (0)
|
|
#define MICROPY_PY_STM (0)
|
|
#define MICROPY_PY_PYB_LEGACY (0)
|
|
#define MICROPY_PY_UHEAPQ (0)
|
|
#define MICROPY_PY_UTIMEQ (0)
|
|
|
|
#define MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE (0)
|
|
#define MICROPY_HW_ENABLE_RTC (1)
|
|
#define MICROPY_HW_ENABLE_ADC (0)
|
|
#define MICROPY_HW_ENABLE_USB (1)
|
|
#define MICROPY_HW_HAS_SWITCH (1)
|
|
|
|
// UART config
|
|
#define MICROPY_HW_UART1_TX (pin_A9)
|
|
#define MICROPY_HW_UART1_RX (pin_A10)
|
|
#define MICROPY_HW_UART2_TX (pin_A2)
|
|
#define MICROPY_HW_UART2_RX (pin_A3)
|
|
|
|
// USART2 is connected to the ST-LINK USB VCP
|
|
#define MICROPY_HW_UART_REPL PYB_UART_2
|
|
#define MICROPY_HW_UART_REPL_BAUD 115200
|
|
|
|
// I2C buses
|
|
#define MICROPY_HW_I2C1_SCL (pin_B8)
|
|
#define MICROPY_HW_I2C1_SDA (pin_B9)
|
|
|
|
// SPI buses
|
|
#define MICROPY_HW_SPI1_NSS (pin_A15)
|
|
#define MICROPY_HW_SPI1_SCK (pin_A5)
|
|
#define MICROPY_HW_SPI1_MISO (pin_A6)
|
|
#define MICROPY_HW_SPI1_MOSI (pin_A7)
|
|
#define MICROPY_HW_SPI2_NSS (pin_B12)
|
|
#define MICROPY_HW_SPI2_SCK (pin_B13)
|
|
#define MICROPY_HW_SPI2_MISO (pin_B14)
|
|
#define MICROPY_HW_SPI2_MOSI (pin_B15)
|
|
|
|
// USER B1 has a pull-up and is active low
|
|
#define MICROPY_HW_USRSW_PIN (pin_B2)
|
|
#define MICROPY_HW_USRSW_PULL (0)
|
|
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING)
|
|
#define MICROPY_HW_USRSW_PRESSED (0)
|
|
|
|
// 4 user LEDs
|
|
#define MICROPY_HW_LED1 (pin_B5) // Green
|
|
#define MICROPY_HW_LED2 (pin_A5) // Green (next to power LED)
|
|
#define MICROPY_HW_LED3 (pin_B6) // Blue
|
|
#define MICROPY_HW_LED4 (pin_B7) // Red
|
|
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
|
|
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
|
|
|
|
// USB config (need to bridge SB15/SB16)
|
|
#define MICROPY_HW_USB_FS (1)
|
|
#define MICROPY_HW_USB_MSC (0)
|
|
#define MICROPY_HW_USB_HID (0)
|
|
#define MICROPY_HW_USB_CDC_RX_DATA_SIZE (256)
|
|
#define MICROPY_HW_USB_CDC_TX_DATA_SIZE (256)
|