mirror of
https://github.com/licsber/micropython.git
synced 2024-09-21 09:30:24 +08:00
181bfb6db2
Since all currently supported boards use pin A9 for this function, the value of the macro MICROPY_HW_USB_VBUS_DETECT_PIN is not actually used, just the fact that it is defined. Addresses issue #1048.
42 lines
1.6 KiB
C
42 lines
1.6 KiB
C
#define NETDUINO_PLUS_2
|
|
|
|
#define MICROPY_HW_BOARD_NAME "NetduinoPlus2"
|
|
#define MICROPY_HW_MCU_NAME "STM32F405RG"
|
|
|
|
#define MICROPY_HW_HAS_SWITCH (1)
|
|
|
|
// On the netuino, the sdcard appears to be wired up as a 1-bit
|
|
// SPI, so the driver needs to be converted to support that before
|
|
// we can turn this on.
|
|
#define MICROPY_HW_HAS_SDCARD (0)
|
|
#define MICROPY_HW_HAS_MMA7660 (0)
|
|
#define MICROPY_HW_HAS_LIS3DSH (0)
|
|
#define MICROPY_HW_HAS_LCD (0)
|
|
#define MICROPY_HW_ENABLE_RNG (1)
|
|
#define MICROPY_HW_ENABLE_RTC (0)
|
|
#define MICROPY_HW_ENABLE_TIMER (1)
|
|
#define MICROPY_HW_ENABLE_SERVO (1)
|
|
#define MICROPY_HW_ENABLE_DAC (0)
|
|
#define MICROPY_HW_ENABLE_I2C1 (0)
|
|
#define MICROPY_HW_ENABLE_SPI1 (0)
|
|
#define MICROPY_HW_ENABLE_SPI3 (0)
|
|
#define MICROPY_HW_ENABLE_CAN (0)
|
|
|
|
// USRSW is pulled low. Pressing the button makes the input go high.
|
|
#define MICROPY_HW_USRSW_PIN (pin_B11)
|
|
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
|
|
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
|
|
#define MICROPY_HW_USRSW_PRESSED (1)
|
|
|
|
// LEDs
|
|
#define MICROPY_HW_LED1 (pin_A10) // Blue LED
|
|
#define MICROPY_HW_LED2 (pin_C13) // White LED (aka Power)
|
|
#define MICROPY_HW_LED3 (pin_A10) // Same as Led(1)
|
|
#define MICROPY_HW_LED4 (pin_C13) // Same as Led(2)
|
|
#define MICROPY_HW_LED_OTYPE (GPIO_MODE_OUTPUT_PP)
|
|
#define MICROPY_HW_LED_ON(pin) (pin->gpio->BSRRL = pin->pin_mask)
|
|
#define MICROPY_HW_LED_OFF(pin) (pin->gpio->BSRRH = pin->pin_mask)
|
|
|
|
// USB VBUS detect pin
|
|
#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
|