mirror of
https://github.com/licsber/micropython.git
synced 2024-09-21 01:20:23 +08:00
67fd58bbd2
Mboot now supports FAT, LFS1 and LFS2 filesystems, to load firmware from.
The filesystem needed by the board must be explicitly enabled by the
configuration variables MBOOT_VFS_FAT, MBOOT_VFS_LFS1 and MBOOT_VFS_LFS2.
Boards that previously used FAT implicitly (with MBOOT_FSLOAD enabled) must
now add the following config to mpconfigboard.h:
#define MBOOT_VFS_FAT (1)
Signed-off-by: Damien George <damien@micropython.org>
87 lines
3.1 KiB
C
87 lines
3.1 KiB
C
#define MICROPY_HW_BOARD_NAME "MIKROE_CLICKER2_STM32"
|
|
#define MICROPY_HW_MCU_NAME "STM32F407"
|
|
|
|
#define MICROPY_HW_HAS_SWITCH (1)
|
|
#define MICROPY_HW_HAS_FLASH (1)
|
|
#define MICROPY_HW_ENABLE_RNG (1)
|
|
#define MICROPY_HW_ENABLE_RTC (1)
|
|
#define MICROPY_HW_ENABLE_DAC (1)
|
|
#define MICROPY_HW_ENABLE_USB (1)
|
|
|
|
// HSE is 25MHz
|
|
#define MICROPY_HW_CLK_PLLM (25)
|
|
#define MICROPY_HW_CLK_PLLN (336)
|
|
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
|
|
#define MICROPY_HW_CLK_PLLQ (7)
|
|
#define MICROPY_HW_CLK_LAST_FREQ (1)
|
|
|
|
// The board has a 32kHz crystal for the RTC
|
|
#define MICROPY_HW_RTC_USE_LSE (1)
|
|
#define MICROPY_HW_RTC_USE_US (0)
|
|
#define MICROPY_HW_RTC_USE_CALOUT (0) // turn on/off PC13 512Hz output
|
|
|
|
// UART config
|
|
// mikroBUS slot 1
|
|
#define MICROPY_HW_UART2_NAME "SLOT1"
|
|
#define MICROPY_HW_UART2_TX (pin_D5)
|
|
#define MICROPY_HW_UART2_RX (pin_D6)
|
|
// mikroBUS slot 2
|
|
#define MICROPY_HW_UART3_NAME "SLOT2"
|
|
#define MICROPY_HW_UART3_TX (pin_D8)
|
|
#define MICROPY_HW_UART3_RX (pin_D9)
|
|
// HDR2
|
|
#define MICROPY_HW_UART4_NAME "HDR2"
|
|
#define MICROPY_HW_UART4_TX (pin_A0)
|
|
#define MICROPY_HW_UART4_RX (pin_A1)
|
|
|
|
// I2C buses
|
|
// mikroBUS slot 2 / HDR2
|
|
#define MICROPY_HW_I2C2_NAME "SLOT2"
|
|
#define MICROPY_HW_I2C2_SCL (pin_B10)
|
|
#define MICROPY_HW_I2C2_SDA (pin_B11)
|
|
// mikroBUS slot 1
|
|
#define MICROPY_HW_I2C3_NAME "SLOT1"
|
|
#define MICROPY_HW_I2C3_SCL (pin_A8)
|
|
#define MICROPY_HW_I2C3_SDA (pin_C9)
|
|
|
|
// SPI buses
|
|
// mikroBUS slot 2 / HDR1
|
|
#define MICROPY_HW_SPI2_NAME "SLOT2"
|
|
#define MICROPY_HW_SPI2_NSS (pin_E11)
|
|
#define MICROPY_HW_SPI2_SCK (pin_B13)
|
|
#define MICROPY_HW_SPI2_MISO (pin_B14)
|
|
#define MICROPY_HW_SPI2_MOSI (pin_B15)
|
|
// mikroBUS slot 1
|
|
#define MICROPY_HW_SPI3_NAME "SLOT1"
|
|
#define MICROPY_HW_SPI3_NSS (pin_E8)
|
|
#define MICROPY_HW_SPI3_SCK (pin_C10)
|
|
#define MICROPY_HW_SPI3_MISO (pin_C11)
|
|
#define MICROPY_HW_SPI3_MOSI (pin_C12)
|
|
|
|
// USRSW is pulled high; pressing the button makes the input go low
|
|
#define MICROPY_HW_USRSW_PIN (pin_E0)
|
|
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
|
|
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING)
|
|
#define MICROPY_HW_USRSW_PRESSED (0)
|
|
|
|
// LEDs
|
|
#define MICROPY_HW_LED1 (pin_E12) // red
|
|
#define MICROPY_HW_LED2 (pin_E15) // red
|
|
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
|
|
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
|
|
|
|
// USB config
|
|
#define MICROPY_HW_USB_FS (1)
|
|
#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
|
|
|
|
// Bootloader configuration (only needed if Mboot is used)
|
|
#define MBOOT_I2C_PERIPH_ID 2
|
|
#define MBOOT_I2C_SCL (pin_B10)
|
|
#define MBOOT_I2C_SDA (pin_B11)
|
|
#define MBOOT_I2C_ALTFUNC (4)
|
|
#define MBOOT_BOOTPIN_PIN (pin_A10)
|
|
#define MBOOT_BOOTPIN_PULL (MP_HAL_PIN_PULL_NONE)
|
|
#define MBOOT_BOOTPIN_ACTIVE (0)
|
|
#define MBOOT_FSLOAD (1)
|
|
#define MBOOT_VFS_FAT (1)
|