micropython/docs/mimxrt/tutorial/intro.rst

126 lines
5.1 KiB
ReStructuredText

.. _mimxrt_intro:
Getting started with MicroPython on the i.MXRT
==============================================
Using MicroPython is a great way to get the most of your i.MXRT board. And
vice versa, the i.MXRT chip is a great platform for using MicroPython. This
tutorial will guide you through setting up MicroPython, getting a prompt, using
the hardware peripherals, and controlling some external components.
Let's get started!
Requirements
------------
The first thing you need is a board with an i.MXRT chip. The MicroPython
software supports the i.MXRT chip itself and any board should work. The main
characteristic of a board is how the GPIO pins are connected to the outside
world, and whether it includes a built-in USB-serial converter to make the
UART available to your PC.
Names of pins will be given in this tutorial using the chip names (eg GPIO2)
and it should be straightforward to find which pin this corresponds to on your
particular board.
Powering the board
------------------
If your board has a USB connector on it then most likely it is powered through
this when connected to your PC. Otherwise you will need to power it directly.
Please refer to the documentation for your board for further details.
Getting the firmware
--------------------
Firmware versions are provided at the
`MicroPython download page <https://micropython.org/download/?port=mimxrt>`_.
You can download the most recent MicroPython firmware .hex or .bin file to load
onto your i.MXRT device. From that download page you have two main choices:
* stable firmware builds
* daily firmware builds
If you are just starting with MicroPython, the best bet is to go for the stable
firmware builds. If you are an advanced, experienced MicroPython i.MXRT user
who would like to follow development closely and help with testing new
features, there are daily builds.
Deploying the firmware
----------------------
Once you have the MicroPython firmware you need to load it onto your
i.MXRT device. The exact procedure for these steps is highly dependent
on the particular board and you will need to refer to its documentation
for details.
Teensy 4.0 and 4.1
~~~~~~~~~~~~~~~~~~
For Teensy 4.0 and 4.1 you have to use the built-in loader together with the PC
loader provided by PJRC. The built-in loader will be activated by pushing the
button on the board. Then you can upload the firmware with the command::
teensy_loader_cli --mcu=imxrt1062 -v -w firmware.hex
IMXRT10xx-EVK boards
~~~~~~~~~~~~~~~~~~~~
The IMXRT10xx-EVK boards have a second USB port connected to a support MCU.
Connecting that USB port to your PC will register a disk drive with the name of
the board. Just copy the firmware.bin file to this drive, and that will start
the flashing procedure. You will know that the flash was complete, if that
drive disappears and reappears. If you decided to install the very useful
Segger open-SDA firmware on that sidekick MCU, then you have to use the debugger
software to upload the i.MXRT firmware.
Seed ARCH MIX board
~~~~~~~~~~~~~~~~~~~
Firmware upload to the Seed ARCH MIX board is less convenient. The vendor
suggests using J-Link as a method and tool. For that, follow the instructions
given by Seed in their Wiki at
https://wiki.seeedstudio.com/Arch_Mix/#flashing-arduino-bootloader-to-arch-mix.
You will need a J-Link debug probe and software. You may find Segger JLink edu
or Segger JLink edu mini convenient. As a matching loader you can use
JFlashLite. The target address for loading is 0x60000000.
The MIMXRT family also support a serial upload method. The software for serial
upload is provided by NXP. The steps to use it are:
- Connect J3, Pin 19 to 3.3V (GPIO_AD_B0_05).
- Change the DIP-Switch settings from off-off-on-off to off-off-off-on
- Push Reset
- Run the upload with: ./FLASH.sh <firmware_image_file name>
- Once the upload has finished, set the DIP-switch back to off-off-on-off.
- Remove the Jumper to J3, Pin19 and push reset
To avoid running the Flash loader as superuser, you can copy the provided udev-rules
script to /etc/udev/rules.d/. FLASH.sh calls two binaries, blhost and sdphost,
which are provided by NXP under the BSD-3-Clause License. A version of these
binaries and the script can be downloaded at
https://github.com/robert-hh/Shared-Stuff/blob/master/mimxrt_serial_downloader.zip.
Serial downloading can be used for the NXP MIMXRT boards as well. But the built-in loader
is much more convenient to use.
Serial prompt
-------------
Once you have the firmware on the device you can access the REPL (Python prompt)
over USB.
From there you can follow the i.MXRT tutorial.
Troubleshooting installation problems
-------------------------------------
If you experience problems during flashing or with running firmware immediately
after it, here are some troubleshooting recommendations:
* Be aware of and try to exclude hardware problems. There are two common
problems: bad power source quality, and worn-out/defective Flash ROM.
Speaking of power source, not just raw amperage is important, but also low
ripple and noise/EMI in general. The most reliable and convenient power
source is a USB port.