Commit Graph

107 Commits

Author SHA1 Message Date
Damien George
fbd47fc46c ports: Consolidate inclusion of umachine module in built-ins.
The inclusion of `umachine` in the list of built-in modules is now done
centrally in py/objmodule.c.  Enabling MICROPY_PY_MACHINE will include this
module.

As part of this, all ports now have `umachine` as the core module name
(previously some had only `machine` as the name).

Signed-off-by: Damien George <damien@micropython.org>
2022-02-03 10:08:54 +11:00
robert-hh
c1841c2d45 mimxrt: Simplify Makefile in selection of flash type.
Simplify it a little bit by combining two sections regarding the
flash type. Thanks to @alphaFred for suggesting it.
2022-01-27 17:05:45 +11:00
robert-hh
da9c3607a5 mimxrt: Add support for the Olimex RT1010 board.
The board.json file is intentionally excluded, until the board will be
sold. But including it into the mimxrt series make it easier to keep
the build up-to-date.
2022-01-27 17:05:45 +11:00
robert-hh
b73073d246 mimxrt: Add USB ID elements.
- Manufacturer, set by MICROPY_HW_USB_STR_MANUF; default "MicroPython"
- Board name, as set by MICROPY_HW_BOARD_NAME
- Unique-ID, same as returned by machine.unique_id()
- USB Vendor ID, as set by MICROPY_HW_USB_VID; default 0xf055
- USB Product ID, as set by MICROPY_HW_USB_PID; default 0x9802
2022-01-27 17:05:34 +11:00
robert-hh
30380962cf mimxrt: Allow to select cs0 or cs1 for SPI.
Using the keyword argument cs=nnn in the constructor. The cs1
pin has to be defined in mpconfigboard.h.
Note: Only a few boards have the CS1 pin exposed to the connectors.
2022-01-27 16:53:30 +11:00
robert-hh
1dc366f901 mimxrt: Replace Pin-config constants by a function call.
The Pin config setting by IOMUXC_SetPinConfig() is supplied by a
bit pattern. That pattern is specific for a MCU family. In preparation
for supporting the MIMXRT117x family, the constant bit pattern is
replaced by a function call, such that the bit pattern is created
at a single place. The code for this functions was taken from
machine_pin.c.

Note: A working port for the MIMXRT1176 exists already.
2022-01-27 16:53:30 +11:00
robert-hh
5bda84aed5 mimxrt: Remove two files from the Seeed Arch Mix directory.
These were leftovers from a previous refactoring in the Seeed Arch Mix
directory.
2022-01-27 16:53:30 +11:00
robert-hh
b8a0358c34 mimxrt: Compensate for a bug in the fsl_lpspi.c file.
This library file has a bug, in that TransferBlocking returns before the
transfer has finished. That is a problem if a write follows immediately
a read.
2022-01-27 16:53:30 +11:00
robert-hh
84b76e4fbf mimxrt: Allow for board-specific flash driver files.
If in a board's mkconfigboard.mk the following symbol is set:

MICROPY_HW_BOARD_FLASH_FILES = 1

then the files:

($BOARD)_flexspi_flash_config.h  and
qspi_nor_flash_config.c  and/or
qspi_hyper_flash_config.c

are expected in the board directory. Otherwise the common files from
the hal directory are used.
2022-01-27 16:53:30 +11:00
robert-hh
2dd3d88409 mimxrt: Support gaps in the SPI an I2C device numbers.
That allows also to use e.g. SPI1 and SPI2 instead SPI0 and SPI1.
2022-01-27 16:53:30 +11:00
Damien George
1892d03740 mimxrt,stm32: Enable MICROPY_PY_USSL_FINALISER.
This is needed because these ports allocate mbedtls data on the MicroPython
heap, and SSL socket objects must be fully cleaned up when they are garbage
collected, to free this memory allocated by mbedtls.  As part of this,
gc_sweep_all() will now ensure that the MP_STATE_PORT(mbedtls_memory)
linked-list is fully deallocated on soft reset.

Signed-off-by: Damien George <damien@micropython.org>
2022-01-08 00:02:04 +11:00
Chris Boudacoff
802ef271b8 mimxrt/hal: Allow readSampleClkSrc to be configured by a board.
Via the MICROPY_HW_FLASH_DQS flag.
2022-01-04 15:42:12 +11:00
Damien George
de43b500bd py/runtime: Allow initialising sys.path/argv with defaults.
If MICROPY_PY_SYS_PATH_ARGV_DEFAULTS is enabled (which it is by default)
then sys.path and sys.argv will be initialised and populated with default
values.  This keeps all bare-metal ports aligned.

Signed-off-by: Damien George <damien@micropython.org>
2021-12-18 00:08:07 +11:00
Jim Mussared
86ce442607 ports: Add '.frozen' as the first entry in sys.path.
Frozen modules will be searched preferentially, but gives the user the
ability to override this behavior.

This matches the previous behavior where "" was implicitly the frozen
search path, but the frozen list was checked before the filesystem.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2021-12-18 00:08:07 +11:00
robert-hh
5ca56aaf16 mimxrt: Tidy up the board flash related files.
- Move the qspi_xxxx_flash_config.c files to hal.
  It turned out that they are less board than flash type specific.
- Change to a common flexspi_flash_config.h header file.
2021-12-14 20:31:20 +01:00
robert-hh
c5dbbf71c0 mimxrt: Use -Og instead of -O0 for DEBUG builds.
Thanks for the hint, Damien. The DEBUG build got very large recently.
The major difference is, that inline function are now inlined and
not included as a function. That's good and maybe bad. The good thing is,
that the code speed si now close to the final code. It could be worse
in single step debugging. I'll see.

Setting this option caused a new warning and a formatting error
to pop up at different places. Fixed as well.
2021-12-14 08:07:52 +01:00
robert-hh
64aa0bcb88 mimxrt: Enable ticks_cpu at boot time for NDEBUG builds only.
Otherwise, it get's in trouble with a Debugger. Reason to be found.
Also: Increase code segment to 2 MB for the MIMXRT1050_EVK build.
2021-12-14 08:07:52 +01:00
robert-hh
74e8db0ed1 mimxrt: Refactor the reading of the machine id.
The ID is read in a single function and used for:
- machine.unique_id()
- Ethernet MAC addresses.
- ...

That facilitates use of other MCU using a different access method for
the ID (e.g. i.MX RT1176).
2021-12-14 08:07:52 +01:00
robert-hh
1e9eaa7af5 mimxrt: Add a driver for the DP83848 PHY device.
Just another choice for the PHY interface.

Added: Keyword option phy_clock=LAN.IN or LAN.OUT
to define the source of the 50MHZ clock for the PHY
interface. The RMII clock is not enabled if it
is generated by a PYH board. Constants:

LAN.IN  The clock is provided by the PHY board.
LAN.OUT The clock is provided by the MCU board.

The default is LAN.OUT or the value set in mpconfigboard.h, which
is currently set to IN only for the SEEED ARCH MIX board. Usage etc:

lan = LAN(phy_type=LAN.PHY_DP83848, phy_clock=LAN.IN)
2021-12-14 08:07:52 +01:00
robert-hh
5d8941ec85 mimxrt: Fix a tiny unnoticed bug in sdcard.c.
This code line will hardly ever be compiled and executed, but since
it is there, it must be correct.
2021-12-14 08:07:52 +01:00
robert-hh
ea09dccfea mimxrt: Re-Enable eth checksum creation by HW.
The initial problem with a wrong ICMP checksum was caused by
the test code setting a checksum and the HW taking that probably as
the start value and ending up with 0xffff. With a checksum field of 0
set by the test code the HW creates the proper checksum.
2021-12-14 08:07:52 +01:00
robert-hh
bbe25f4704 mimxrt: Support selection of PHY type and address.
Useful for boards without a PHY interface, where that has to be
attached. Like the Seed ARCH MIX board or Vision SOM. Phy drivers
supported so far are:

- KSZ8081
- DP83825
- LAN8720

More to come. Usage e.g.:
lan = LAN(phy_type=LAN.PHY_LAN8720, phy_addr=1)

The default values are those set in mpconfigboard.h.
2021-12-14 08:07:52 +01:00
robert-hh
bc1b0fd2c1 mimxrt: Define UART 0 on MIMXRT boards.
UART 0 is attached to the Debug USB port. The settings are
115200 Baud, 8N1.
For MIMXRT1010_EVK this is identical to UART1. For the other boards,
this is an additional UART.
2021-12-14 08:07:52 +01:00
robert-hh
81f706aee4 mimxrt: Support PWM using the FLEXPWM and QTMR modules.
Frequency range 15Hz/18Hz to > 1 MHz, with decreasing resolution of the
duty cycle.  The basic API is supported as documentated, except that
keyword parameters are accepted for both the instatiaton and the
PWM.init() call.

Extensions: support PWM for channel pairs.  Channel pairs are declared by
supplying 2-element tuples for the pins.  The two channels of a pair must
be the A/B channel of a FLEXPWM module.  These form than a complementary
pair.

Additional supported keyword arguments:

- center=value Defines the center position of a pulse within the pulse
  cycle.  The align keyword is actually shortcut for center.

- sync=True|False: If set to True, the channels will be synchronized to a
  submodule 0 channel, which has already to be enabled.

- align=PWM.MIDDLE | PMW.BEGIN | PWM.END. It defines, whether synchronized
  channels are Center-Aligned or Edge-aligned.  The channels must be either
  complementary a channel pair or a group of synchronized channels.  It may
  as well be applied to a single channel, but withiout any benefit.

- invert= 0..3. Controls ouput inversion of the pins.  Bit 0 controls the
  first pin, bit 1 the second.

- deadtime=time_ns time of complementary channels for delaying the rising
  slope.

- xor=0|1|2 xor causes the output of channel A and B to be xored.  If
  applied to a X channel, it shows the value oif A ^ B.  If applied to an A
  or B channel, both channel show the xored signal for xor=1.  For xor=2,
  the xored signal is split between channels A and B.  See also the
  Reference Manual, chapter about double pulses.  The behavior of xor=2 can
  also be achieved using the center method for locating a pulse within a
  clock period.

The output is enabled for board pins only.

CPU pins may still be used for FLEXPWM, e.g. as sync source, but the signal
will not be routed to the output.  That applies only to FLEXPWM pins.  The
use of QTMR pins which are not board pins will be rejected.

As part of this commit, the _WFE() statement is removed from
ticks_delay_us64() to prevent PWM glitching during calls to sleep().
2021-11-24 13:48:27 +11:00
robert-hh
7d7d29dbe2 mimxrt: Fix mp_hal_quiet_timing_enter()/exit() so timer still runs.
The initial code disabled IRQs, which caused the us-ticks timer to stop.
The change here changes the priotity level, such that the timer still runs.
2021-11-16 23:20:06 +11:00
robert-hh
7cc9b257a9 mimxrt/boards: Update the board.json files and add deploy_xx.md files.
- Add board.md files for MIMXRT1060_EVK and MIMXRT1064_EVK warning about
  their experimental state.
- Add separate deploy_teensy.md and deploy_mimxrt.md files.
2021-11-16 23:17:42 +11:00
robert-hh
d72d699dad mimxrt/boards: Add the Seeed ARCH MIX board.
The ARCH MIX board exposes the Ethernet Pins at it's connectors.  Therefore
the software is configured for using a LAN8720 PHY device.  Breakout boards
with the LAN8720 are easily available.
2021-11-16 23:11:21 +11:00
Mike Causer
7f14344428 ports: Add images, features and urls to board.json. 2021-10-28 15:25:38 +11:00
Jim Mussared
e359b077dd ports: Add board.json for all boards.
This will be used by https://micropython.org/download/ to generate the
full listing of boards and firmware files.

Optionally supports a board.md for additional customisation of the
download page, as well as deploy.md for flashing instructions.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2021-10-27 14:04:53 +11:00
robert-hh
9f6604eb27 mimxrt: Enable the platform module. 2021-10-25 23:54:52 +11:00
robert-hh
4f89c38a6a mimxrt: Optimize the runtime speed.
By moving code to ITCM, like vm, gc, parse, runtime.  The change affects
mostly the execution speed of MicroPython code.  The speed is increased by
up to a factor of 6, especially for MCU with small cache.
2021-10-25 23:54:47 +11:00
robert-hh
90b45efa6a mimxrt/boards/make-pins.py: Allow empty lines and comments in pins.csv. 2021-10-25 23:53:51 +11:00
robert-hh
6754213a9d mimxrt/modmachine: Implement soft_reset() and unique_id() functions. 2021-10-25 23:53:48 +11:00
robert-hh
a12e318948 mimxrt/mpconfigport.h: Enable f-strings. 2021-10-25 23:52:35 +11:00
robert-hh
c827d4b7ab mimxrt: Extend the help() message and README.md. 2021-10-25 23:52:08 +11:00
robert-hh
e7572776c3 mimxrt: Add dht_readinto() to the mimxrt module, and freeze dht.py.
The change affects dht.py from the drivers directory as well to include the
logic for the mimxrt port.
2021-10-25 23:49:28 +11:00
robert-hh
99221cd118 mimxrt: Fix cycle counter for time.ticks_cpu() and machine.bitstream().
Prior to this commit mp_hal_ticks_cpu() was not started properly.  It only
started when the code was executed with a debugger attached, except for the
Teensy (i.MXRT1062) boards.  As an additional fix, the CYYCNT timer is now
started at boot time.

Also rename mp_hal_ticks_cpu_init() to mp_hal_ticks_cpu_enable().
2021-10-25 15:50:44 +11:00
robert-hh
06d1b02014 mimxrt/dma_channel: Fix the DMA channel management.
The MIMXRT1011 has only 16 channels, so size the channel list accordingly.
2021-10-25 15:50:44 +11:00
robert-hh
101d2ddea3 mimxrt/hal: Remove duplicate definitions from flexspi_hyper_flash.h. 2021-10-25 15:50:44 +11:00
robert-hh
68146aa197 mimxrt/boards: Fix the D14/D15 pin assignment of MIMXRT1050/60/64_EVK.
There are several PCB layouts in the market under the same name.
2021-10-25 15:50:38 +11:00
robert-hh
c2e4759cfa mimxrt/modmachine: Implement machine.WDT() and machine.reset_cause().
The API follows that of rp2, stm32, esp32, and the docs.

    wdt=machine.WDT(0, timeout)

        Timeout is given in ms. The valid range is 500 to 128000 (128
        seconds) with 500 ms granularity. Values outside of that range will
        be silently aligned.

    wdt.feed()

        Resets the watchdog timer (feeding).

    wdt.timeout_ms(value)

        Sets a new timeout and feeds the watchdog.

        This is a new, preliminary method which is not yet documented.

    reset_cause = machine.reset_cause()

        Values returned:

        1  Power On reset
        3  Watchdog reset
        5  Software reset: state after calling machine.reset()

More elaborate API functions are supported by the MCU, like an interrupt
called a certain time after feeding.  But for port cosistency that is not
implemented.
2021-10-25 15:43:56 +11:00
robert-hh
1866ed7e2e mimxrt/eth: Add LAN support and integrate the network module.
This commit implements 10/100 Mbit Ethernet support in the mimxrt port.

The following boards are configured without ETH network:
- MIMXRT1010_EVK
- Teensy 4.0

The following boards are configured with ETH network:
- MIMXRT1020_EVK
- MIMXRT1050_EVK
- MIMXRT1060_EVK
- MIMXRT1064_EVK
- Teensy 4.1

Ethernet support tested with TEENSY 4.1, MIMRTX1020_EVK and MIMXRT1050_EVK.
Build tested with Teensy 4.0 and MIMXRT1010_EVK to be still working.
Compiles and builds properly for MIMXRT1060_EVK and MIMXRT1064_EVK, but not
tested lacking suitable boards.

Tested functions are:
- ping works bothway
- simple UDP transfer works bothway
- ntptime works
- the ftp server works
- secure socker works
- telnet and webrepl works

The MAC address is 0x02 plus 5 bytes from the manifacturing info field,
which can be considered as unique per device.

Some boards do not wire the RESET and INT pin of the PHY transceiver.  For
operation, these are not required.  If they are defined, they will be used.
2021-10-25 15:14:26 +11:00
Philipp Ebensberger
7e62c9707a mimxrt/sdram: Add SDRAM support.
Adds support for SDRAM via `SEMC` peripheral. SDRAM support can be
enabled in the mpconfigboard.mk file by setting `MICROPY_HW_SDRAM_AVAIL`
to `1` and poviding the size of the RAM via `MICROPY_HW_FLASH_SIZE`.

When SDRAM support is enabled the whole SDRAM is currently used used
for MicroPython heap.

Signed-off-by: Philipp Ebensberger
2021-10-22 08:23:24 +02:00
Philipp Ebensberger
0d7366c912 mimxrt: Rework flash configuration.
- Moves definition of BOARD_FLASH_SIZE and other header files related to
	flash configuration into the Makefile.
- Adds board specific clock_config.h.
- Adds board.h, pin_mux.h, and peripherals.h as they are
	required by NXP MCU SDK in order to use our own clock_config.h.
- Renames board specific FlexSPI configuration files.
- Updates flash frequency of MIMXRT1020_EVK
- Creates separated flash_config files for QSPI NOR and
	QSPI Hyper flash.
- Unifies VFS start address to be @ 1M for 1010 and 1020 boards.
- Unifies 1050EVK boards
- Adds support to both NOR and HyperFlash on boards with
	both capabilities.
- Adds automatic FlexRAM initialization to start-up code based on
	linker script and NXP HAL.
- Applies code formatting to all files in mimxrt port.

With this change the flash configuration is restructured and
organized. This simplifies the configuration process and
provides a better overview of each board's settings. With the integration
of clock_config.h, board.h, pin_mux.h, and peripherals.h we gain better
control of the settings and clock configurations. Furthermore the
implementation of an explicit FlexRAM setup improves the system
performance and allows for performance tuning.

Signed-off-by: Philipp Ebensberger
2021-09-14 13:52:52 +02:00
robert-hh
61b7c098b9 mimxrt/machine_bitstream: Add bitstream function to machine module.
Following the code example for ESP32 of Jim Mussard.

As a side effect:
- mp_hal_ticks_cpu() was implemented,
- mp_hal_get_cpu_freq() and mp_hal_ticks_cpu_init() were added and used.
- mp_hal_pin_high() and mp_hal_pin_low() were changed for symmetry
2021-09-10 13:32:53 +10:00
Philipp Ebensberger
87f97e490c mimxrt/sdcard: Implement SDCard driver.
- Configures `PLL2->PFD0` with **198MHz** as base clock of
	`USDHCx` peripheral.
- Adds guards for SDCard related files via `MICROPY_PY_MACHINE_SDCARD`
- Adds creation of pin defines for SDCard to make-pins.py
- Adds new configuration option for SDCard peripheral pinout
        to mpconfigport.h
- Adds interrupt handling support instead of polling
- Adds support for `ADMA2` powered data transfer
- Configures SDCard to run in HS (high-speed mode) with **50MHz** only!

SDCard support is optional and requires `USDHC` peripheral.
Thus this driver is not available on `MIMXRT1010_EVK`.
SDCard support is enabled by setting `MICROPY_PY_MACHINE_SDCARD = 1`
in mpconfigboard.mk.

Signed-off-by: Philipp Ebensberger
2021-09-07 20:45:33 +02:00
Damien George
d41f6dde56 extmod/modonewire: Make _onewire module configurable via macro option.
Signed-off-by: Damien George <damien@micropython.org>
2021-09-02 13:11:23 +10:00
Damien George
afe0634c98 extmod/machine_spi: Make SoftSPI configurable via macro option.
Signed-off-by: Damien George <damien@micropython.org>
2021-09-02 13:11:23 +10:00
Damien George
122d901ef1 extmod/machine_i2c: Make SoftI2C configurable via macro option.
The zephyr port doesn't support SoftI2C so it's not enabled, and the legacy
I2C constructor check can be removed.

Signed-off-by: Damien George <damien@micropython.org>
2021-09-02 13:11:23 +10:00
Philipp Ebensberger
a1dc7277d9 mimxrt/machine_pin: Implement ioctl for Pin.
To make machine.Signal work correctly (among other things).  The solution
is taken over from the rp2 port.

Signed-off-by: Philipp Ebensberger
2021-08-16 15:03:50 +10:00