Add posibility to override linker script "_fs_size" from make by adding the
FS_SIZE parameter. The syntax of value is linker script syntax. For
example, the value of 131072 bytes can be written as 128K like this:
FS_SIZE=128K.
If not set, default value for "_fs_size" from linker script will be used.
Disable MICROPY_FATFS_MULTI_PARTITION configuration because there is no
partition table in the flash for FATFS to read.
Also, set MICROPY_FATFS_MAX_SS to the size of a flash page. For nrf51 the
value 1024 is set. For nrf52/nrf91 the value 4096 is set.
This documents parameters that can be passed to make to enable a specific
file system to included in the build. Also, document the Makefile override
parameter "FS_SIZE" that can be used to tune the size of the flash region
to use as internal flash file system.
Update flash.c to also be compiled in when
MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE is enabled and SoftDevice is
present.
Update bluetooth/ble_drv.c to forward flash events to flash.c when
MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE is enabled.
This commit adds the "nrf" module for port specific modules and objects.
Included in it is the "Flash" object which exposes a block device
implementation to access internal SoC flash.
Thanks to @aykevl aka Ayke van Laethem for the initial implementation.
Calculate the unused flash area on the target device. The values will be
exposed by _unused_flash_start and _unused_flash_length. The start address
and the length are not aligned to either word or pages.
This allows changing the frequency to: 100kHz, 200kHz, 400kHz, 800kHz,
1MHz, 2MHz, 4MHz, 8MHz, 16MHz, 32MHz, 64MHz. For frequencies 2MHz and
below, low power run (LPR) mode is enabled automatically.
Signed-off-by: Damien George <damien@micropython.org>
For consistency with other board-level config macros that begin with
MICROPY_HW_USB.
Also allow boards in the mimxrt, nrf and samd ports to configure these
values.
Signed-off-by: Damien George <damien@micropython.org>
Reverse operations are supported on stm32 and rp2, and esp32 has enough
space to also enable inplace operations, to make it complete.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This enables optional support for the hardware UART to use the RTS and/or
CTS pins for flow control.
The new "flow" constructor keyword specifies a bitmask of RTS and/or CTS.
This matches the interface used by machine.UART on stm32 and rp2.
Previously on ESP32 it was possible to specify which pins to use for the
RTS and CTS signals, but hardware flow control was never functional: CTS
was not checked before transmitting bytes, and RTS was always driven high
(signalling no buffer space available). With this patch, CTS and RTS both
operate as expected.
This also includes an update to the machine.UART documentation.
Signed-off-by: Will Sowerbutts <will@sowerbutts.com>
Hyperflash is used by the MIMXRT1050_EVKB, MIMXRT1060_EVK and
MIMXRT1064_EVK boards.
This commit includes:
- add support for Hyperflash
- modify MIMXRT1060_EVK and MIMXRT1064_EVK to change from QSPI to
hyperflash.
- minor incidental changes to other boards so they still build
Note: Erasing a sector on the hyperflash is slow. It takes about a second,
which seems too long, but matches the data sheet.
Add basic support for LEGO HUB NO.6 (e.g. LEGO SPIKE Prime, LEGO MINDSTORMS
Robot Inventor).
See README.md for details.
Thanks to @dpgeorge for helping put this together.
Signed-off-by: Tobias Thyrrestrup <tt@LEGO.com>
It needs to use a different function because the formula to compute the
baudrate on LPUART1 is different to a normal UART.
Fixes issue #7466.
Signed-off-by: Damien George <damien@micropython.org>
Prior to this fix, if the UART hardware FIFO had a few chars but still
below the FIFO trigger threshold, and the ringbuf was empty, the read
function would timeout if timeout==0 (the default timeout).
This fix follows the suggestion of @iabdalkader.
The RX IRQ does not trigger if the FIFO is less than the trigger level, in
which case characters may be available in the FIFO, yet not in the ringbuf,
and the ioctl returns false.
* Make SDRAM test cache-aware for newer MCUs.
* Use the defined data bus width (instead of the fixed 8-bits).
* Allow optional failure on error with verbose error messages.
* Test speed is now inverted (test accepts exhaustive instead fast).
This helps the OS switch to and give other threads processing time during
the sleep. It also ensures that pending events are handled, even when
sleeping for 0ms.
Fixes issue #5344.
Signed-off-by: Damien George <damien@micropython.org>
Call MICROPY_EVENT_POLL_HOOK even on very short delays so that busy loops
that call sleep_ms still yield to events and other threads.
See related issue #5344.
