Commit Graph

75 Commits

Author SHA1 Message Date
robert-hh
ed1f42cb49 nrf/modules/machine/pwm: Support using all 4 channels of a PWM module.
These have the same frequency, but can have different duty cycle and
polarity.

pwm.deinit() stops all channels of a module, but does not release the
module.  pwm.init() without arguments restarts all outputs.
2023-03-10 10:44:02 +11:00
robert-hh
e3b877826c nrf/modules/machine/soft_pwm: Add PWM for nrf51x boards using soft PWM.
Using extmod/machine_pwm.c for the Python bindings and the existing
softpwm.c driver, by just adding the interface.

Properties:
- Frequency range 1-3906 Hz.
- All PWM outputs run at the same frequency but can have different duty
  cycles.
- Limited to the P0.x pins.

Since it uses the existing softpwm.c mechanism, it will be affected by
playing music with the music class.
2023-03-10 10:44:02 +11:00
robert-hh
a1f838cdf1 nrf/modules/machine/pwm: Use extmod/machine_pwm.c for PWM module.
This is a breaking change, making the hardware PWM on the nrf port
compatible with the other ports providing machine.PWM.

Frequency range 4Hz - ~5.4 MHz.  The base clock range is 125kHz to 16 MHz,
and the divider range is 3 - 32767.

The hardware supports up to four outputs per PWM device with different duty
cycles, but only one output is (and was) supported.
2023-03-10 10:43:55 +11:00
robert-hh
cf43df4caa nrf/modules/machine/pwm: Add paramter checks and error messages. 2023-03-10 10:30:16 +11:00
Damien George
e8f5cfe0e1 nrf: Rename MICROPY_PY_MACHINE_TIMER to MICROPY_PY_MACHINE_TIMER_NRF.
So that it doesn't clash with the extmod version.

Also make the default for this enabled, so that most boards do not need to
configure it.

Signed-off-by: Damien George <damien@micropython.org>
2022-10-27 14:30:58 +11:00
iabdalkader
93f3910fe7 nrf: Rename machine I2C, PWM, SPI, UART types consistently across ports.
This renames:
- machine_hard_i2c_type -> machine_i2c_type
- machine_hard_pwm_type -> machine_pwm_type
- machine_hard_spi_type -> machine_spi_type
- machine_hard_uart_type -> machine_uart_type
2022-10-22 12:58:54 +11:00
Jim Mussared
94beeabd2e py/obj: Convert make_new into a mp_obj_type_t slot.
Instead of being an explicit field, it's now a slot like all the other
methods.

This is a marginal code size improvement because most types have a make_new
(100/138 on PYBV11), however it improves consistency in how types are
declared, removing the special case for make_new.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-09-19 19:06:15 +10:00
Jim Mussared
6da41b5900 py/obj: Merge getiter and iternext mp_obj_type_t slots.
The goal here is to remove a slot (making way to turn make_new into a slot)
as well as reduce code size by the ~40 references to mp_identity_getiter
and mp_stream_unbuffered_iter.

This introduces two new type flags:
- MP_TYPE_FLAG_ITER_IS_ITERNEXT: This means that the "iter" slot in the
  type is "iternext", and should use the identity getiter.
- MP_TYPE_FLAG_ITER_IS_CUSTOM: This means that the "iter" slot is a pointer
  to a mp_getiter_iternext_custom_t instance, which then defines both
  getiter and iternext.

And a third flag that is the OR of both, MP_TYPE_FLAG_ITER_IS_STREAM: This
means that the type should use the identity getiter, and
mp_stream_unbuffered_iter as iternext.

Finally, MP_TYPE_FLAG_ITER_IS_GETITER is defined as a no-op flag to give
the default case where "iter" is "getiter".

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-09-19 19:06:13 +10:00
Jim Mussared
9dce82776d all: Remove unnecessary locals_dict cast.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-09-19 19:06:01 +10:00
Jim Mussared
662b9761b3 all: Make all mp_obj_type_t defs use MP_DEFINE_CONST_OBJ_TYPE.
In preparation for upcoming rework of mp_obj_type_t layout.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-09-19 19:06:01 +10:00
robert-hh
cc0249c936 nrf/modules/machine/uart: Implement uart.flush() and uart.txdone().
Since uart.write() of the nrf port waits until all bytes but the last
one have been sent, uart.flush() and uart.txdone() are implemented
as empty functions to provide API consistency.

uart.flush()

flush() will always return immediately, even if the last byte
may still be sent.

ret = uart.txdone()

uart.txdone() will always return True, even if the last byte
may still be sent.
2022-08-31 00:18:40 +10:00
Jim Mussared
8a0ee5a5c0 py/objstr: Split mp_obj_str_from_vstr into bytes/str versions.
Previously the desired output type was specified.  Now make the type part
of the function name.  Because this function is used in a few places this
saves code size due to smaller call-site.

This makes `mp_obj_new_str_type_from_vstr` a private function of objstr.c
(which is almost the only place where the output type isn't a compile-time
constant).

This saves ~140 bytes on PYBV11.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-08-26 16:43:55 +10:00
David Lechner
8a69c54211 nrf: Use MP_REGISTER_ROOT_POINTER().
This uses MP_REGISTER_ROOT_POINTER() to register all port-specific root
pointers for the nrf port.

Signed-off-by: David Lechner <david@pybricks.com>
2022-07-18 13:50:34 +10:00
robert-hh
60539ea162 nrf/drivers/usb: Probe for interrupt char in USB CDC task.
And ensure that the input queue is empty when scheduling the interrupt.
2022-07-17 00:11:14 +10:00
iabdalkader
6753c53318 nrf/modmachine: Add machine.idle() function.
This improves the compatibility of the nrf port machine module with common
drivers, by adding a machine.idle() alias for lightsleep.
2022-07-08 12:37:59 +10:00
iabdalkader
d8f5669532 nrf/modmachine: Add machine.bootloader() and make it customisable. 2022-06-17 13:37:44 +10:00
Damien George
efe23aca71 all: Remove third argument to MP_REGISTER_MODULE.
It's no longer needed because this macro is now processed after
preprocessing the source code via cpp (in the qstr extraction stage), which
means unused MP_REGISTER_MODULE's are filtered out by the preprocessor.

Signed-off-by: Damien George <damien@micropython.org>
2022-06-02 16:31:37 +10:00
Jim Mussared
4eab44a1ec extmod: Make extmod modules use MP_REGISTER_MODULE.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-05-18 20:49:12 +10:00
Jim Mussared
0e7bfc88c6 all: Use mp_obj_malloc everywhere it's applicable.
This replaces occurences of

    foo_t *foo = m_new_obj(foo_t);
    foo->base.type = &foo_type;

with

    foo_t *foo = mp_obj_malloc(foo_t, &foo_type);

Excludes any places where base is a sub-field or when new0/memset is used.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-05-03 22:28:14 +10:00
Damien George
fbd47fc46c ports: Consolidate inclusion of umachine module in built-ins.
The inclusion of `umachine` in the list of built-in modules is now done
centrally in py/objmodule.c.  Enabling MICROPY_PY_MACHINE will include this
module.

As part of this, all ports now have `umachine` as the core module name
(previously some had only `machine` as the name).

Signed-off-by: Damien George <damien@micropython.org>
2022-02-03 10:08:54 +11:00
David P
d3f6ce7dc3 nrf/modules: Replace master/slave with controller/peripheral in SPI.
Also remove mistaken usage of MASTER/SLAVE constants in comments.
2021-07-18 11:23:41 +10:00
Damien George
136369d72f all: Update to point to files in new shared/ directory.
Signed-off-by: Damien George <damien@micropython.org>
2021-07-12 17:08:10 +10:00
Bruno Martins
94fb5e7f5a nrf: Add machine.memXX, and allow boards to customise some features. 2021-05-18 12:01:51 +10:00
Damien George
e9e9c76ddf all: Rename mp_keyboard_interrupt to mp_sched_keyboard_interrupt.
To match mp_sched_exception() and mp_sched_schedule().

Signed-off-by: Damien George <damien@micropython.org>
2021-04-30 15:13:43 +10:00
Damien George
64180f0742 extmod/machine_i2c: Add init protocol method for generic I2C bindings.
Hardware I2C implementations must provide a .init() protocol method if they
want to support reconfiguration.  Otherwise the default is that i2c.init()
raises an OSError (currently the case for all ports).

mp_machine_soft_i2c_locals_dict is renamed to mp_machine_i2c_locals_dict to
match the generic SPI bindings.

Fixes issue #6623 (where calling .init() on a HW I2C would crash).

Signed-off-by: Damien George <damien@micropython.org>
2020-11-23 19:45:04 +11:00
Damien George
71f3ade770 ports: Support legacy soft I2C/SPI construction via id=-1 arg.
With a warning that this way of constructing software I2C/SPI is
deprecated.  The check and warning will be removed in a future release.

This should help existing code to migrate to the new SoftI2C/SoftSPI types.

Signed-off-by: Damien George <damien@micropython.org>
2020-10-01 12:57:10 +10:00
Damien George
39d50d129c ports: Add SoftI2C and SoftSPI to machine module where appropriate.
Previous commits removed the ability for one I2C/SPI constructor to
construct both software- or hardware-based peripheral instances.  Such
construction is now split to explicit soft and non-soft types.

This commit makes both types available in all ports that previously could
create both software and hardware peripherals: machine.I2C and machine.SPI
construct hardware instances, while machine.SoftI2C and machine.SoftSPI
create software instances.

This is a breaking change for use of software-based I2C and SPI.  Code that
constructed I2C/SPI peripherals in the following way will need to be
changed:

    machine.I2C(-1, ...)            ->  machine.SoftI2C(...)
    machine.I2C(scl=scl, sda=sda)   ->  machine.SoftI2C(scl=scl, sda=sda)

    machine.SPI(-1, ...)            ->  machine.SoftSPI(...)
    machine.SPI(sck=sck, mosi=mosi, miso=miso)
                        ->  machine.SoftSPI(sck=sck, mosi=mosi, miso=miso)

Code which uses machine.I2C and machine.SPI classes to access hardware
peripherals does not need to change.

Signed-off-by: Damien George <damien@micropython.org>
2020-10-01 12:57:10 +10:00
Damien George
c35deb2625 extmod/machine_i2c: Rename type to SoftI2C and add custom print method.
Also rename machine_i2c_type to mp_machine_soft_i2c_type.  These changes
make it clear that it's a soft-I2C implementation, and match SoftSPI.

Signed-off-by: Damien George <damien@micropython.org>
2020-10-01 12:57:10 +10:00
Martin Fischer
15574cd665 nrf: Add support for time.ticks_xxx functions using RTC1.
This commit adds time.ticks_ms/us support using RTC1 as the timebase.  It
also adds the time.ticks_add/diff helper functions.  This feature can be
enabled using MICROPY_PY_TIME_TICKS.  If disabled the system uses the
legacy sleep methods and does not have any ticks functions.

In addition support for MICROPY_EVENT_POLL_HOOK was added to the
time.sleep_ms(x) function, making this function more power efficient and
allows support for select.poll/asyncio.  To support this, the RTC's CCR0
was used to schedule a ~1msec event to wakeup the CPU.

Some important notes about the RTC timebase:

- Since the granularity of RTC1's ticks are approx 30usec, time.ticks_us is
not perfect, does not have 1us resolution, but is otherwise quite usable.
For tighter measurments the ticker's 1MHz counter should be used.

- time.ticks_ms(x) should *not* be called in an IRQ with higher prio than
the RTC overflow irq (3).  If so it introduces a race condition and
possibly leads to wrong tick calculations.

See #6171 and #6202.
2020-07-08 23:47:02 +10:00
Jim Mussared
e7f8c7d9a3 nrf: Update to work with nrfx v2.0.0, to match TinyUSB.
Commit 6cea369b89 updated the TinyUSB
submodule to a version based on nrfx v2.0.0.  This commit updates the nrf
port to work with the latest TinyUSB and nrfx v2.0.0.
2020-05-15 15:06:02 +10:00
Jim Mussared
def76fe4d9 all: Use MP_ERROR_TEXT for all error messages. 2020-04-05 15:02:06 +10:00
Damien George
ac8383a95d nrf: Use MICROPY_HW_ENABLE_RNG instead of MICROPY_PY_RANDOM_HW_RNG.
The "random" module no longer uses the hardware RNG (the extmod version of
this module has a pseudo-random number generator), so the config option
MICROPY_PY_RANDOM_HW_RNG is no longer meaningful.  This commit replaces it
with MICROPY_HW_ENABLE_RNG, which controls whether the hardware RNG is
included in the build.
2020-02-18 12:43:16 +11:00
Damien George
ad7213d3c3 py: Add mp_raise_msg_varg helper and use it where appropriate.
This commit adds mp_raise_msg_varg(type, fmt, ...) as a helper for
nlr_raise(mp_obj_new_exception_msg_varg(type, fmt, ...)).  It makes the
C-level API for raising exceptions more consistent, and reduces code size
on most ports:

   bare-arm:   +28 +0.042%
minimal x86:  +100 +0.067%
   unix x64:   -56 -0.011%
unix nanbox:  -300 -0.068%
      stm32:  -204 -0.054% PYBV10
     cc3200:    +0 +0.000%
    esp8266:   -64 -0.010% GENERIC
      esp32:  -104 -0.007% GENERIC
        nrf:  -136 -0.094% pca10040
       samd:    +0 +0.000% ADAFRUIT_ITSYBITSY_M4_EXPRESS
2020-02-13 11:52:40 +11:00
Damien George
97eca38c4f py: Add mp_raise_type helper macro and use it where appropriate.
This provides a more consistent C-level API to raise exceptions, ie moving
away from nlr_raise towards mp_raise_XXX.  It also reduces code size by a
small amount on some ports.
2020-02-13 11:03:37 +11:00
Glenn Ruben Bakke
82fe6b0526 nrf: Add nrf9160 base support.
This patch add basic building blocks for nrf9P60.

It also includes a secure bootloader which forwards all
possible peripherals that are user selectable to become
non-secure. After configuring Flash, RAM and peripherals
the secure bootloader will jump to the non-secure domain
where MicroPython is placed.

The minimum size of a secure boot has to be a flash
block of 32Kb, hence why the linker scripts are
offsetting the main application this much.

The RAM offset is set to 128K, to allow for later
integration of Nordic Semiconductor's BSD socket
library which reserves the range 0x20010000 - 0x2001FFFF.
2019-10-10 21:35:27 +02:00
Glenn Ruben Bakke
c561ae61a1 nrf/uart: Add support for UARTE (EasyDMA). 2019-10-02 21:20:56 +02:00
Glenn Ruben Bakke
02a8c31eef nrf/temp: Move module configuration guard.
This patch moves the check for MICROPY_PY_MACHINE_TEMP to come
before the inclusion of nrf_temp.h. The nrf_temp.h depends on
the NRF_TEMP_Type which might not be defined for all nRF devices.
2019-10-02 21:15:48 +02:00
Glenn Ruben Bakke
d2e730b727 nrf/i2c: Add support for TWIM (EasyDMA). 2019-10-02 20:42:06 +02:00
Jim Mussared
353ed7705f nrf/boards/make-pins.py: Fix gen of board pins to use correct index.
It was previously not taking into account that the list of pins was sparse,
so using the wrong index.  The boards/X/pins.csv was generating the wrong
data for machine.Pin.board.

As part of this fix rename the variables to make it more clear what the
list contains (only board pins).
2019-09-05 22:52:24 +10:00
Damien George
9e90e2528b nrf/machine/adc: Fix mapping of ADC channel to pin. 2019-09-05 22:13:04 +10:00
Damien George
c7fb93b844 nrf/machine/adc: Allow to pass a Pin object in to ADC constructor. 2019-09-05 22:13:04 +10:00
Damien George
9cad134a2f nrf/machine/adc: Add ADC.read_u16() method. 2019-09-05 22:13:04 +10:00
Damien George
1fe1ff935b nrf: Clean up source by removing tabs, trailing spaces, non-ASCII chars. 2019-08-28 13:34:45 +10:00
Damien George
456c89f749 nrf/uart: Make UART print output something, and add write method. 2019-05-22 12:47:48 +10:00
Damien George
302ffdba7f nrf/uart: Change UART driver to be non-blocking and use IRQs.
As part of this, ctrl-C is now able to interrupt a running program.
2019-05-22 12:47:19 +10:00
Damien George
bb29bde102 nrf/machine/i2c: Update to support new C-level I2C API. 2019-05-20 15:04:29 +10:00
Stig Bjørlykke
c72391c4ce nrf/pwm: Remove superfluous NULL in machine_hard_pwm_instances.
Remove unneeded NULL entry in machine_hard_pwm_instances[] when not
building for NRF52_SERIES.
2019-02-20 22:52:18 +01:00
Damien George
6e30f96b0b ports: Convert legacy uppercase macro names to lowercase. 2019-02-12 14:54:51 +11:00
Stig Bjørlykke
98f790b03a nrf/timer: Fix disabling Timer 1 when using soft PWM.
Don't exclude the Timer instance 1 entry from machine_timer_obj[] when
using soft PWM. The usage is already checked when creating the Timer,
so just create an empty entry.
2019-02-02 11:15:52 +01:00
Ayke van Laethem
e8678cd1c9 nrf/pin: Print pull information in Pin.__str__. 2019-01-31 17:38:13 +11:00