Commit Graph

54 Commits

Author SHA1 Message Date
Damien George
e0a0719416 stm32: Add initial support for STM32WL MCUs.
Signed-off-by: Damien George <damien@micropython.org>
2022-02-04 09:43:43 +11:00
Herwin Grobben
8f68e26f79 stm32: Add support for G4 MCUs, and add NUCLEO_G474RE board defn.
This commit adds support for the STM32G4 series of MCUs, and a board
definition for NUCLEO_G474RE.  This board has the REPL on LPUART1 which is
connected to the on-board ST-link USB-UART.
2022-02-01 16:21:01 +11:00
Damien George
84969194a1 stm32/flashbdev: Support generic flash storage config via link symbols.
A board can now define the following linker symbols to configure its flash
storage layout:

    _micropy_hw_internal_flash_storage_start
    _micropy_hw_internal_flash_storage_end
    _micropy_hw_internal_flash_storage_ram_cache_start
    _micropy_hw_internal_flash_storage_ram_cache_end

And optionally have a second flash segment by configuring
MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE_SEGMENT2 to 1 and defining:

    _micropy_hw_internal_flash_storage2_start
    _micropy_hw_internal_flash_storage2_end

Signed-off-by: Damien George <damien@micropython.org>
2021-11-29 13:01:51 +11:00
MikeTeachman
6d5296e65e stm32,esp32: In machine_i2s, make object reference arrays root pointers.
This change eliminates the risk of the IRQ callback accessing invalid data.
Discussed here:
https://github.com/micropython/micropython/pull/7183#discussion_r660209875

Signed-off-by: Mike Teachman <mike.teachman@gmail.com>
2021-11-13 12:22:42 +11:00
Jan Staal
9e2423e730 stm32: Add support for H7A3(Q)/H7B3(Q), and STM32H73B3I_DK board defn.
This commit is based upon prior work of @dpgeorge and @koendv.

MCU support for the STM32H7A3 and B3 families MCUs:
- STM32H7A3xx
- STM32H7A3xxQ (SMPS)
- STM32H7B3xx
- STM32H7B3xxQ (SMPS)

Support has been added for the STM32H7B3I_DK board.

Signed-off-by: Jan Staal <info@janstaal.com>
2021-09-16 12:29:28 +10:00
Damien George
3b32b3d1b3 stm32/usbd_cdc_interface: Rename USBD_CDC_xx opts to MICROPY_HW_USB_xx.
Signed-off-by: Damien George <damien@micropython.org>
2021-08-07 23:13:58 +10:00
Damien George
f28e8b9073 stm32/usbd_desc: Rename USBD_xxx descriptor opts to MICROPY_HW_USB_xxx.
Signed-off-by: Damien George <damien@micropython.org>
2021-08-07 23:13:58 +10:00
Damien George
96c6b8cae3 ports: Rename USBD_VID/PID config macros to MICROPY_HW_USB_VID/PID.
For consistency with other board-level config macros that begin with
MICROPY_HW_USB.

Also allow boards in the mimxrt, nrf and samd ports to configure these
values.

Signed-off-by: Damien George <damien@micropython.org>
2021-08-07 23:13:55 +10:00
Damien George
ee4ffc1804 stm32/powerctrl: Add MICROPY_HW_ENTER_BOOTLOADER_VIA_RESET option.
When disabled the bootloader is entered via a direct jump.  When enabled
the bootloader is entered via a system reset then a jump.  It's enabled by
default to retain the existing behaviour, which is the recommended way.

Signed-off-by: Damien George <damien@micropython.org>
2021-05-12 13:44:41 +10:00
iabdalkader
a1111b83ed stm32/sdio: Allow configuring the SDMMC periph used for SDIO.
This can now be selected by setting MICROPY_HW_SDIO_SDMMC, which defaults
to 1, ie SDMMC1.  The pins can also be selected and default to the standard
C8/C9/C10/C11/C12/D2.
2021-04-30 11:26:04 +10:00
Damien George
cf7e71fa43 stm32/sdcard: Allow configuring the SDMMC periph used for SD/MMC card.
This can now be selected by setting MICROPY_HW_SDCARD_SDMMC, which defaults
to 1, ie SDMMC1.  This commit also renames the SD pin configuration macros
from MICROPY_HW_SDMMC2_xxx to MICROPY_HW_SDCARD_xxx, as well as renaming
MICROPY_HW_SDMMC_BUS_WIDTH to MICROPY_HW_SDCARD_BUS_WIDTH.

Signed-off-by: Damien George <damien@micropython.org>
2021-04-30 00:58:17 +10:00
Damien George
00963a4e69 stm32/powerctrl: Allow a board to configure AHB and APB clock dividers.
Signed-off-by: Damien George <damien@micropython.org>
2021-04-07 12:47:09 +10:00
Damien George
680ce45323 stm32/rfcore: Allow BLE settings to be changed by a board.
Two of the defaults have also changed in this commit:

- MICROPY_HW_RFCORE_BLE_LSE_SOURCE changed from 1 to 0, which configures
  the LsSource to be LSE (needed due to errata 2.2.1).

- MICROPY_HW_RFCORE_BLE_VITERBI_MODE changed from 0 to 1, which enables
  Viterbi mode, following all the ST examples.

Signed-off-by: Damien George <damien@micropython.org>
2021-03-02 12:14:54 +11:00
Chris Mason
9d674cf7ab stm32/uart: Add support for LPUART1 on L0, L4, H7 and WB MCUs.
Add LPUART1 as a standard UART.  No low power features are supported, yet.
LPUART1 is enabled as the next available UART after the standard U(S)ARTs:

    STM32WB:      LPUART1 = UART(2)
    STM32L0:      LPUART1 = UART(6)
    STM32L4:      LPUART1 = UART(6)
    STM32H7:      LPUART1 = UART(9)

On all ports: LPUART1 = machine.UART('LP1')

LPUART1 is enabled by defining MICROPY_HW_LPUART1_TX and
MICROPY_HW_LPUART1_RX in mpconfigboard.h.

Signed-off-by: Chris Mason <c.mason@inchipdesign.com.au>
2021-02-21 15:49:32 +11:00
Damien George
9b78f3e6c6 stm32: Make pyb, uos, utime, machine and onewire modules configurable.
The default for these is to enable them, but they can now be disabled
individually by a board configuration.

Signed-off-by: Damien George <damien@micropython.org>
2021-02-17 14:42:46 +11:00
Damien George
d1f120b142 stm32/main: Introduce MICROPY_HW_FLASH_MOUNT_AT_BOOT config option.
It's enabled by default to retain the existing behaviour.  A board can
disable this option if it manages mounting the filesystem itself, for
example in frozen code.

Signed-off-by: Damien George <damien@micropython.org>
2021-01-29 15:02:55 +11:00
Damien George
e43a74a4db drivers/memory/spiflash: Add MICROPY_HW_SPIFLASH_ENABLE_CACHE option.
This only needs to be enabled if a board uses FAT FS on external SPI flash.
When disabled (and using external SPI flash) 4k of RAM can be saved.

Signed-off-by: Damien George <damien@micropython.org>
2020-12-18 13:39:32 +11:00
Damien George
1e4e2644ec stm32: Add support for a board to reserve certain peripherals.
Allows reserving CAN, I2C, SPI, Timer and UART peripherals.  If reserved
the peripheral cannot be accessed from Python.

Signed-off-by: Damien George <damien@micropython.org>
2020-12-07 17:22:08 +11:00
Jim Mussared
119c88ef17 stm32/flash: Implement WB55 flash locking.
This is needed to moderate concurrent access to the internal flash, as
while an erase/write is in progress execution will stall on the wireless
core due to the bus being locked.

This implements Figure 10 from AN5289 Rev 3.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2020-11-16 17:08:30 +11:00
Damien George
69661f3343 all: Reformat C and Python source code with tools/codeformat.py.
This is run with uncrustify 0.70.1, and black 19.10b0.
2020-02-28 10:33:03 +11:00
Chris Mason
d61e7a6d8a stm32/uart: Add support for UART4/5 on L0 MCUs. 2019-12-05 15:31:41 +11:00
iabdalkader
f7a07b3605 stm32: Add support for FDCAN peripheral, exposed as pyb.CAN.
The new fdcan.c file provides the low-level C interface to the FDCAN
peripheral, and pyb_can.c is updated to support both traditional CAN and
FDCAN, depending on the MCU being compiled for.
2019-09-23 17:00:54 +10:00
Damien George
97e8e036c5 stm32/usbd: Support USB device mode on STM32L432 MCUs. 2019-08-15 12:46:04 +10:00
Damien George
bf733c27bb stm32/usbd: Introduce MICROPY_HW_USB_IS_MULTI_OTG to simplify USB config
This is an internal config value that is enabled for MCUs that have
multiple OTG instances, to simplify #if configuration of the USB code.
2019-08-15 12:19:28 +10:00
Chris Wilson
3d02ebb4e8 stm32/sdcard: Support configuring the SD/MMC bus width to 1 or 4 bits.
Some SD/MMC breakout boards don't support 4-bit bus mode.  This adds a new
macro MICROPY_HW_SDMMC_BUS_WIDTH that allows each board to define the width
of the SD/MMC bus interface used on that board, defaulting to 4 bits.
2019-08-08 12:53:05 +10:00
Damien George
59b7166d87 stm32: Add initial support for STM32WBxx MCUs.
This new series of MCUs is similar to the L4 series with an additional
Cortex-M0 coprocessor.  The firmware for the wireless stack must be managed
separately and MicroPython does not currently interface to it.  Supported
features so far include: RTC, UART, USB, internal flash filesystem.
2019-07-17 16:33:31 +10:00
Damien George
f302f784e9 stm32/usb: Add config options to disable USB MSC and/or HID.
The new configurations MICROPY_HW_USB_MSC and MICROPY_HW_USB_HID can be
used by a board to enabled or disable MSC and/or HID.  They are both
enabled by default.
2019-07-16 14:39:21 +10:00
Damien George
23d9c6a0fd stm32: Add initial support for STM32L0xx MCUs. 2019-07-05 17:24:59 +10:00
Damien George
0c29502ad9 stm32/usb: Refactor CDC VCP code to enable N CDC interfaces.
The board config option MICROPY_HW_USB_ENABLE_CDC2 is now changed to
MICROPY_HW_USB_CDC_NUM, and the latter should be defined to the maximum
number of CDC interfaces to support (defaults to 1).
2019-05-30 21:11:04 +10:00
Damien George
ddc657658a stm32/machine_i2c: Simplify ROM initialisation of static HW I2C objects. 2019-05-21 12:38:34 +10:00
Andrew Leech
ed2b6ea0a8 stm32/i2c: Make timeout for hardware I2C configurable.
Previously the hardware I2C timeout was hard coded to 50ms which isn't
guaranteed to be enough depending on the clock stretching specs of the I2C
device(s) in use.

This patch ensures the hardware I2C implementation honors the existing
timeout argument passed to the machine.I2C constructor.  The default
timeout for software and hardware I2C is now 50ms.
2019-05-21 12:20:19 +10:00
Chris Mason
1b956ec817 stm32: Add support for F413 MCUs.
Includes:
- Support for CAN3.
- Support for UART9 and UART10.
- stm32f413xg.ld and stm32f413xh.ld linker scripts.
- stm32f413_af.csv alternate function mapping.
- startup_stm32f413xx.s because F413 has different interrupt vector table.
- Memory configuration with: 240K filesystem, 240K heap, 16K stack.
2019-05-02 16:26:53 +10:00
Damien George
46e5d6b889 stm32/rtc: Add auto-LSE-bypass detection with fallback to LSE then LSI.
If MICROPY_HW_RTC_USE_BYPASS is enabled the RTC startup goes as follows:
- RTC is started with LSE in bypass mode to begin with
- if that fails to start (after a given timeout) then LSE is reconfigured
  in non-bypass
- if that fails to start then RTC is switched to LSI
2019-04-11 12:09:21 +10:00
Damien George
7ce2a08231 stm32: Add support for MMC driver, exposed via pyb.MMCard class.
Enable it via MICROPY_HW_ENABLE_MMCARD.
2019-04-01 17:04:43 +11:00
Damien George
9670b26526 stm32: Rename MICROPY_HW_HAS_SDCARD to MICROPY_HW_ENABLE_SDCARD.
For consistency with the majority of other MICROPY_HW_ENABLE_xxx macros.
2019-04-01 15:21:26 +11:00
Francisco J. Manno
f938e70c69 stm32: Add compile-time option to use HSI as clock source.
To use HSI instead of HSE define MICROPY_HW_CLK_USE_HSI as 1 in the board
configuration file.  The default is to use HSE.

HSI has been made the default for the NUCLEO_F401RE board to serve as an
example, and because early revisions of this board need a hardware
modification to get HSE working.
2019-03-05 15:49:08 +11:00
Andrew Leech
ce0c581179 stm32/main: Add board config option to enable/disable mounting SD card.
The new option MICROPY_HW_SDCARD_MOUNT_AT_BOOT can now be defined to 0 in
mpconfigboard.h to allow SD hardware to be enabled but not auto-mounted at
boot.  This feature is enabled by default to retain previous behaviour.

Previously, if an SD card is enabled in hardware it is also used to boot
from.  While this can be disabled with a SKIPSD file on internal flash,
this wont be available at first boot or if the internal flash gets
corrupted.
2018-12-22 01:30:47 +11:00
Andrew Leech
338635ccc6 stm32/main: Add configuration macros for board to set heap start/end.
The macros are MICROPY_HEAP_START and MICROPY_HEAP_END, and if not defined
by a board then the default values will be used (maximum heap from SRAM as
defined by linker symbols).

As part of this commit the SDRAM initialisation is moved to much earlier in
main() to potentially make it available to other peripherals and avoid
re-initialisation on soft-reboot.  On boards with SDRAM enabled the heap
has been set to use that.
2018-10-05 17:30:18 +10:00
Andrew Leech
84f4d58479 stm32/dcmi: Add F4/F7/H7 hal files and dma definitions for DCMI periph. 2018-09-21 12:12:49 +10:00
Damien George
ea7e747979 stm32: Add support for STM32F0 MCUs. 2018-05-28 21:49:49 +10:00
Damien George
f497723802 stm32: Allow to have no storage support if there are no block devices.
If no block devices are defined by a board then storage support will be
disabled.  This means there is no filesystem provided by either the
internal flash or external SPI flash.  But the VFS system can still be
enabled and filesystems provided on external devices like an SD card.
2018-05-28 21:45:46 +10:00
Ryan Shaw
b9ff46f1ed stm32: Enable UART7/8 on F4 series that have these peripherals. 2018-05-16 11:55:07 +10:00
Damien George
92c5e2708d stm32/modpyb: Introduce MICROPY_PY_PYB_LEGACY config option for pyb mod.
This is enabled by default.  When it is disabled all legacy functions and
classes in the pyb module are excluded from the build.
2018-05-14 13:49:22 +10:00
Damien George
8a949ba599 stm32: Introduce MICROPY_PY_STM config to include or not the stm module.
By default the stm module is included in the build, but a board can now
define MICROPY_PY_STM to 0 to not include this module.  This reduces the
firmware by about 7k.
2018-04-24 12:01:49 +10:00
Damien George
3d5d76fb73 stm32/main: Allow a board to configure the label of the flash FS.
To change the default label a board should define:

    #define MICROPY_HW_FLASH_FS_LABEL "label"
2018-04-11 16:52:22 +10:00
Damien George
cf9fc7346d stm32: Allow a board to configure the HSE in bypass mode.
To use HSE bypass mode the board should define:

    #define MICROPY_HW_CLK_USE_BYPASS (1)

If this is not defined, or is defined to 0, then HSE oscillator mode is
used.
2018-04-11 16:46:47 +10:00
Damien George
a7ebac2eae stm32/can: Allow CAN pins to be configured per board.
This patch allows a given board to configure which pins are used for the
CAN peripherals, in a similar way to all the other bus peripherals (I2C,
UART, SPI).  To enable CAN on a board the mpconfigboard.h file should
define (for example):

    #define MICROPY_HW_CAN1_TX (pin_B9)
    #define MICROPY_HW_CAN1_RX (pin_B8)
    #define MICROPY_HW_CAN2_TX (pin_B13)
    #define MICROPY_HW_CAN2_RX (pin_B12)

And the board config file should no longer define MICROPY_HW_ENABLE_CAN.
2018-04-11 16:35:24 +10:00
Damien George
b833f170c3 stm32/main: Only update reset_mode if board doesn't use a bootloader.
If the board is configured to use a bootloader then that bootloader will
pass through the reset_mode.
2018-03-29 16:16:58 +11:00
Damien George
626d6c9756 stm32/storage: Introduce MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE cfg.
This config variable controls whether to support storage on the internal
flash of the MCU.  It is enabled by default and should be explicitly
disabled by boards that don't want internal flash storage.
2018-03-10 00:59:43 +11:00
iabdalkader
61d463ad07 stm32/mpconfigboard_common: Add STM32H7 common configuration. 2018-03-09 15:12:44 +11:00