Commit Graph

258 Commits

Author SHA1 Message Date
robert-hh
711bac511e rp2/main: Keep UART REPL with DEBUG=1 and MICROPY_HW_ENABLE_UART_REPL=1.
For builds with DEBUG=1 and MICROPY_HW_ENABLE_UART_REPL=1, calling
stdio_init_all() in main() detaches the UART input from REPL.  This change
suppresses calling stdio_init_all() then.
2023-03-20 22:33:45 +11:00
robert-hh
be686e634e rp2: Allow disabling USB via MICROPY_HW_ENABLE_USBDEV config.
Previously, setting MICROPY_HW_ENABLE_USBDEV to 0 caused build errors.  The
change affects the nrf and samd ports as well, so MICROPY_HW_ENABLE_USBDEV
had to be explicitly enabled there.

The configuration options MICROPY_HW_ENABLE_USBDEV and
MICROPY_HW_ENABLE_UART_REPL are independent, and can be enabled or disabled
by a board.

Signed-off-by: Damien George <damien@micropython.org>
2023-03-20 22:33:45 +11:00
iabdalkader
a197823eb7 ports: Fix MCU tags in Arduino board.json files. 2023-03-20 15:22:24 +11:00
Christian Clauss
4376c969f6 all: Fix Python comparison to None and True, and use "not in".
These are basic PEP8 recommendations.
2023-03-10 13:32:24 +11:00
cpottle9
c80e7c14e6 rp2: Allocate GC heap from unused RAM.
Borrowing an idea from the mimxrt port (also stm32 port): in the loader
input file memmap_mp.ld calculate __GcHeapStart and __GcHeapEnd as the
unused RAM.  Then in main.c use these addresses as arguments to gc_init().

The benefits of this change are:

1) When libraries are added or removed in the future changing BSS usage,
   main.c's sizing of the GC heap does not need to be changed.

2) Currently these changes make the GC area about 30 KBytes larger, eg on
   PICO_W the GC heap increases from 166016 to 192448 bytes.  Without that
   change this RAM would never get used.

3) If someone wants to disable one or more SRAM blocks on the RP2040 to
   reduce power consumption it will be easy: just change the MEMORY section
   in memmap_mp.ld.  For instance to not use SRAM2 and SRAM3 change it to:

        MEMORY
        {
            FLASH(rx) : ORIGIN = 0x10000000, LENGTH = 2048k
            RAM(rwx) : ORIGIN =  0x21000000, LENGTH = 128k
            SCRATCH_X(rwx) : ORIGIN = 0x20040000, LENGTH = 4k
            SCRATCH_Y(rwx) : ORIGIN = 0x20041000, LENGTH = 4k
        }

   Then to turn off clocks for SRAM2 and SRAM3 from MicroPython, set the
   appropriate bits in WAKE_EN0 and SLEEP_EN0.

Tested by running the firmware.uf2 file on PICO_W and displaying
micropython.mem_info().  Confirmed GC total size approximately matched the
size calculated by the loader.

Signed-off-by: cpottle9 <cpottle9@outlook.com>
2023-03-09 12:00:02 +11:00
David Grayson
f80d040c03 rp2/modrp2: Disable other core, shorten delay to 8us in bootsel_button.
This function seems to work fine in multi-core applications now.

The delay is now in units of microseconds instead of depending on the clock
speed, and is adjustable by board configuration headers.

Also added documentation.
2023-03-09 11:44:20 +11:00
Tomofumi Inoue
673957b643 rp2/modrp2: Support reading the BOOTSEL button on the Pico board.
And any other board that exposes this pin with a button.
2023-03-09 11:43:39 +11:00
iabdalkader
dc2186c35b rp2/boards/ARDUINO_NANO_RP2040_CONNECT: Include "senml" in manifest. 2023-03-09 10:38:06 +11:00
iabdalkader
6bb60745be rp2/boards/ARDUINO_NANO_RP2040_CONNECT: Add more external pins.
Add the missing A4, A5 external (Nina-W controlled) pins.
2023-03-08 00:59:36 +11:00
iabdalkader
fd202fe757 rp2/boards/ARDUINO_NANO_RP2040_CONNECT: Include "time" in manifest.
Freeze the micropython-lib time module to get strftime.
2023-03-08 00:52:54 +11:00
iabdalkader
ddf39793f3 rp2/pendsv: Add MICROPY_BOARD_PENDSV_ENTRIES for board customisation. 2023-03-07 15:59:37 +11:00
Jim Mussared
bad0098a49 stm32: Update to use the open-source lib version of cyw43-driver.
This removes the previous WiFi driver from drivers/cyw43 (but leaves behind
the BT driver), and makes the stm32 port (i.e. PYBD and Portenta) use the
new "lib/cyw43-driver" open-source driver already in use by the rp2 port.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2023-03-01 01:27:12 +11:00
Jim Mussared
a377302623 extmod/modnetwork: Add network.hostname() and network.country().
This provides a standard interface to setting the global networking config
for all interfaces and interface types.

For ports that already use either a static hostname (mimxrt, rp2) they will
now use the configured value. The default is configured by the port
(or optionally the board).

For interfaces that previously supported .config(hostname), this is still
supported but now implemented using the global network.hostname.

Similarly, pyb.country and rp2.country are now deprecated, but the methods
still exist (and forward to network.hostname).

Because ESP32/ESP8266 do not use extmod/modnetwork.c they are not affected
by this commit.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2023-03-01 01:26:17 +11:00
Jim Mussared
8e430a7d43 rp2/Makefile: Allow specifying BOARD_DIR on make command line.
This matches the behavior of the makefile ports but implemented for CMake,
making it easy to specify custom board definitions.

This work was funded through GitHub Sponsors.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2023-02-23 09:50:07 +11:00
Damien George
b257c0152b rp2/cyw43_configport: Specify the chipset firmware include file.
Required by the latest version of cyw43-driver.

Signed-off-by: Damien George <damien@micropython.org>
2023-02-17 14:03:19 +11:00
Damien George
c6140ad0d4 rp2/mpconfigport: Enable os.dupterm and hashlib.sha1 on all boards.
This further aligns the features available on Pico and Pico W boards.

os.dupterm is generally useful, but can still be disabled by a board if
needed.  hashlib.sha1 requires mbedtls for the implementation, but that's
always available (due to ucryptolib's requirements).  The entire hashlib
module can still be disabled by an individual board if needed.

Fixes issue #7881.

Signed-off-by: Damien George <damien@micropython.org>
2023-02-17 13:43:03 +11:00
Jim Mussared
5812611ab2 rp2/boards/ARDUINO_NANO_RP2040_CONNECT: Use default aioble.
The default now includes all sub-components (security, l2cap, etc)
and using the kwarg options is no longer supported.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2023-02-16 12:32:03 +11:00
Damien George
0afe60b876 rp2/rp2_pio: Track use of PIO resources and free them on soft reset.
Prior to this commit, on Pico W (where the CYW43 driver is enabled) the PIO
instruction memory was not released on soft reset, so using PIO after a
soft reset would eventually (after a few soft resets) lead to ENOMEM when
allocating a PIO program.

This commit fixes that by tracking the use of PIO memory by this module and
freeing it on soft reset.

Similarly, use of the state machines themselves are tracked and released on
soft reset.

Fixes issue #9003.

Signed-off-by: Damien George <damien@micropython.org>
2023-02-07 14:52:36 +11:00
Jim Mussared
6250337c9c ports: Make all network-capable boards use bundle-networking.
This will ensure that any board with networking support gets:
 - webrepl
 - mip
 - urequests
 - ntptime

This work was funded through GitHub Sponsors.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2023-02-01 12:42:06 +11:00
David Lechner
3446d440f6 shared/runtime/gchelper: Drop cpu directive from ARM asm helpers.
This drops the `.cpu` directive from the ARM gchelper_*.s files.  Having
this directive breaks the linker when targeting older CPUs (e.g. `-mthumb
-mthumb-interwork` for `-mcpu=arm7tdmi`).  The actual target CPU should be
determined by the compiler options.

The exact CPU doesn't actually matter, but rather the supported assembly
instruction set.  So the files are renamed to *_thumb1.s and *thumb2.s to
indicate the instruction set support instead of the CPU support.

Signed-off-by: David Lechner <david@pybricks.com>
2023-01-28 15:51:38 +11:00
Jay Greco
be420bf9bb rp2/boards/NULLBITS_BIT_C_PRO: Add Bit-C PRO board. 2023-01-28 15:14:48 +11:00
Damien George
67fac4ebc5 rp2/machine_pin: Fix configuring OPEN_DRAIN with initial value.
Prior to this commit, Pin(Pin.OPEN_DRAIN, value=0) would not set the
initial value of the open-drain pin to low, instead it would be high.

Signed-off-by: Damien George <damien@micropython.org>
2023-01-24 17:29:45 +11:00
Damien George
8a0353525f rp2/main: Use mp_printf in nlr_jump_fail.
The mp_plat_print output is already being used by the subsequent call to
mp_obj_print_exception().  And this eliminates all references to printf for
this port (at least in non-debug builds).

Signed-off-by: Damien George <damien@micropython.org>
2023-01-24 16:58:29 +11:00
robert-hh
d4a4cde42e rp2: Fix crash in a pin.irq handler.
When accessing the argument of the irq function.
2023-01-22 17:49:10 +01:00
iabdalkader
d02f089058 rp2/boards: Add pin CSV files to board definitions.
Pin defines are:
- For Pico define board pins and the default LED pin (WL_GPIO25).
- For Pico-W define board pins, external pins and the default
  LED pin (WL_GPIO0).
- For the Nano-RP2040, define board pins, external pins and
  the default LED pin (GPIO25)
- For all other boards, the pins.csv defines the LED pin (if any)
  for backwards compatibility with code that assumes there's always
  an LED pin.
2023-01-16 11:44:28 +11:00
iabdalkader
7d01f38170 drivers/ninaw10: Implement machine.Pin external pin controls. 2023-01-16 11:44:28 +11:00
iabdalkader
c214c9e648 rp2/machine_pin: Add support for named pins and alternate functions.
This commit adds support for generating named pin mappings for all pins
including CPU, board-defined, LED and externally controlled pins.  CPU pins
are mapped to `pin_GPIO<n>`, externally-controlled pins are mapped to
`pin_EXT_GPIO<n>`, and defined conditionally (up to 10 pins, and can be
expanded in the future), and they are non-const to allow `machine-pin.c` to
write the pin object fields.  Both CPU and externally controlled pins are
generated even if there's no board CSV file; if one exists it will just be
added to board pins.
2023-01-16 11:44:26 +11:00
iabdalkader
66e0cfc3b9 rp2/machine_pin: Refactor the machine.Pin class for external GPIO.
Handle externally controlled GPIO pins more generically, by removing all
CYW43-specific code from `machine_pin.c`, and adding hooks to initialise,
configure, read and write external pins.  This allows any driver for an
on-board module which controls GPIO pins (such as CYW43 or NINA), to
provide its own implementation of those hooks and work seamlessly with
`machine_pin.c`.
2023-01-16 11:37:18 +11:00
robert-hh
5890a17ae0 rp2/rp2_flash: Call MICROPY_EVENT_POLL_HOOK_FAST after reading flash.
To allow the USB to work in cases where there is a lot of filesystem
access, in particular on boot.

For example, registering of the USB CDC interface may fail if:
- the board file system is lfs2 (default), and
- sys.path contains entries for the local file system (default), and
- files are imported by boot.py or main.py from frozen bytecode of the file
  system (common) and the file system contains many files, like 100.

In that case the board is very busy with scanning LFS, and registering the
USB interface seems to time out.  This commit fixes this by allowing the
USB to make progress during filesystem reads.

Also switch existing MICROPY_EVENT_POLL_HOOK uses in this file to
MICROPY_EVENT_POLL_HOOK_FAST now that the latter macro exists.
2023-01-12 16:53:02 +11:00
Paul Grayson
b208cf23e2 rp2/mphalport: Change order of pin operations to prevent glitches.
When switching from a special function like SPI to an input or output,
there was a brief period after the function was disabled but before the
pin's I/O state was configured, in which the state would be poorly defined.
This fixes the problem by switching off the special function after fully
configuring the I/O state.

Fixes #10226.

Signed-off-by: Paul Grayson <pdg@alum.mit.edu>
2023-01-12 16:36:03 +11:00
Paul Grayson
f0f5c6568d rp2/machine_pwm: Fix overflows with freq > 268 MHz.
There were several places where 32-bit integer could overflow with
frequencies of 2^28 Hz or above (~268 MHz).  This fixes those overflows and
also introduces rounding for more accurate duty_ns computations.

Signed-off-by: Paul Grayson <pdg@alum.mit.edu>
2023-01-12 16:28:12 +11:00
Paul Grayson
b5823604a0 rp2/machine_pwm: Use more accurate formulas for freq and duty_u16.
This changes the freq() and duty_u16() functions to use more simpler, more
accurate formulas, in particular increasing the frequency accuracy from a
few percent to a fraction of a percent in many cases.

Signed-off-by: Paul Grayson <pdg@alum.mit.edu>
2023-01-12 16:28:00 +11:00
Felix Dörre
439298be15 rp2: Fix lightsleep to work with interrupts and cyw43 driver.
This commit prevents the device from "hanging" when using lightsleep while
the WiFi chip is active.

Whenever the WiFi chip wants to interrupt the microcontroller to notify it
for a new package, it sets the CYW43_PIN_WL_HOST_WAKE pin to high,
triggering an IRQ.  However, as polling the chip cannot happen in an
interrupt handler, it subsequently notifies the pendsv-service to do a poll
as soon as the interrupt handler ended.  In order to prevent a new
interrupt from happening immediately afterwards, even before the poll has
run, the IRQ handler disables interrupts from the pin.

The first problem occurs, when a WiFi package arrives while the main loop
is in cyw43-code.  In order to prevent concurrent access of the hardware,
the network code blocks pendsv from running again while entering lwIP code.

The same holds for direct cyw43 code (like changing the cyw43-gpios, i.e.
the LED on the Pico W).  While the pendsv is disabled, interrupts can still
occur to schedule a poll (and disable further interrupts), but it will not
run.  This can happen while the microcontroller is anywhere in rp2040 code.

In order to preserve power while waiting for cyw43 responses,
cyw43_configport.h defines CYW43_DO_IOCTL_WAIT and
CYW43_SDPCM_SEND_COMMON_WAIT to __WFI().  While this might work in most
cases, there are 2 edge cases where it fails:
- When an interrupt has already been received by the cyw43 stack, for
  example due to an incoming ethernet packet.
- When the interrupt from the cyw43 response comes before the
  microcontroller entered the __WFI() instruction.

When that happens, wfi will just block forever as no further interrupts are
received.  The only way to safely use wfi to wake up from an interrupt is
inside a critical section, as this delays interrupts until the wfi is
entered, possibly resuming immediately until interrupts are reenabled and
the interrupt handler is run.  Additionally this critical section needs to
check whether the interrupt has already been disabled and pendsv was
triggered, as in such a case, wfi can never be woken up, and needs to be
skipped, because there is already a package from the network chip waiting.
Note that this turns cyw43_yield into a nop (and thereby the cyw43-loops
into busy waits) from the second time onwards, as after the first call, a
pendsv request will definitely be pending.  More logic could be added, to
explicitly enable the interrupt in this case.

Regarding lightsleep, this code has a similar problem.  When an interrupt
occurs during lightsleep, the IRQ and pendsv handler and thereby poll are
run immediately, with the clocks still disabled, causing the SPI transfers
to fail.  If we don't want to add complex logic inside the IRQ handler we
need to protect the whole lightsleep procedure form interrupts with a
critical section, exiting out early if an interrupt is pending for whatever
reason.  Only then we can start to shut down clocks and only enable
interrupts when the system is ready again.  Other interrupt handlers might
also be happy, that they are only run when the system is fully operational.

Tested on a Pico W, calling machine.lightsleep() within an endless loop and
pinging from the outside.
2022-12-20 15:54:51 +11:00
Jim Mussared
5f8f32f917 extmod/modnetwork: Use a type protocol to implement NIC functions.
This was previously implemented by adding additional members to the
mp_obj_type_t defined for each NIC, which is difficult to do cleanly with
the new object type slots mechanism. The way this works is also not
supported on GCC 8.x and below.

Instead replace it with the type protocol, which is a much simpler way of
achieving the same thing.

This affects the WizNet (in non-LWIP mode) and Nina NIC drivers.

This work was funded through GitHub Sponsors.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-12-15 17:40:06 +11:00
iabdalkader
e35bcb0f0b rp2/boards/ARDUINO_NANO_RP2040: Add more modules and enable MD5 hash.
Changes in this commit are:
- Enable MD5 hash to verify Nina WiFi firmware.
- Add ntptime, urequests and espflash to manifest.
2022-11-14 19:06:51 +11:00
Angus Gratton
c8913fdbfa rp2: Allow enabling USB device without enabling USB-CDC.
Requires changing the USB-CDC stdin/stdout guards from
MICROPY_HW_ENABLE_USBDEV to the new (in this port)
MICROPY_HW_USB_CDC.
2022-11-11 16:49:18 +11:00
Angus Gratton
2e6e53057b shared/tinyusb: Further refactor static USB device implementation.
App the mp_ prefix to usbd_ symbols and files which are defined here and
not in TinyUSB.

rp2 only for now. This includes some groundwork for dynamic USB devices
(defined in Python).

This work was funded through GitHub Sponsors.

Signed-off-by: Angus Gratton <angus@redyak.com.au>
2022-11-11 16:47:36 +11:00
Blake Felt
eed4eb2645 shared/tinyusb: Create common TinyUSB code for reuse by ports.
This code originates from the rp2 port, and the rp2 port has been updated
to use this common code.
2022-11-11 16:33:30 +11:00
robert-hh
acadc0a7dc rp2/modmachine: Move dht_readinto() to the machine module. 2022-11-09 15:57:17 +11:00
iabdalkader
345f1d2395 rp2/cyw43_configport: Make sure only core0 executes a __WFI().
This commit executes __WFI() on core 0 only to avoid core1 locking up since
it doesn't enable any interrupts by default (except for `SIO_IRQ_PROC1`).
This fixes a lockup when calling `cyw43_do_ioctl` from core1.

Fixes issue #9597.
2022-11-09 12:00:10 +11:00
robert-hh
8447fef9f9 rp2/mphalport: Add a timeout to mp_hal_stdout_tx_strn().
If USB CDC is connected and the board sends data, but the host does not
receive the data, the device locks up.  This is fixed in this commit by
having a timeout of 500ms, after which time the transmission is skipped.

Fixes issue #9634.
2022-11-09 11:12:53 +11:00
Damien George
8874a09119 extmod/mbedtls: Enable elliptic curve DH and DSA cryptography.
This is necessary to access sites that only support these protocols.

The rp2 port already has ECDH enabled, so this just adds ECDSA there.  The
other ports now gain both ECDH and ECDSA.  The code size increase is:

- rp2 (PICO_W): +2916 bytes flash, +24 bytes BSS
- stm32 (PYBD_SF6): +20480 bytes flash, +32 bytes data, +48 bytes BSS
- mimxrt (TEENSY41): +20708 bytes flash, +32 bytes data, +48 bytes BSS
- unix (standard x86-64): +39344 executable, +1744 bytes data, +96 BSS

This is obviously a large increase in code size.  But there doesn't seem to
be any other option because without elliptic curve cryptography devices are
partially cut off from the internet.  For use cases that require small
firmware size, they'll need to build custom firmware with a custom mbedtls
config.

Signed-off-by: Damien George <damien@micropython.org>
2022-10-22 19:08:21 +11:00
Damien George
9347545f9e extmod/mbedtls: Enable MBEDTLS_TLS_DEFAULT_ALLOW_SHA1_IN_KEY_EXCHANGE.
This was already enabled on all ports except mimxrt.  Now it's enabled on
all of them.

Signed-off-by: Damien George <damien@micropython.org>
2022-10-22 19:06:21 +11:00
Damien George
b337678964 extmod/mbedtls: Add common configuration file, and use it in all ports.
This is a no-op change.

Signed-off-by: Damien George <damien@micropython.org>
2022-10-22 19:06:21 +11:00
iabdalkader
22ad45fda6 rp2: Rename machine I2C type consistently across ports.
This renames:
- machine_hw_i2c_type -> machine_i2c_type
2022-10-22 12:56:58 +11:00
robert-hh
92d9118038 rp2/fatfs_port: Fix the modification date of files.
It was off by 2000 % 128 == 80 years.

Addresses issue #9535.
2022-10-12 00:31:38 +11:00
Jim Mussared
924a3e03ec top: Replace upip with mip everywhere.
Updates all README.md and docs, and manifests to `require("mip")`.

Also extend and improve the documentation on freezing and packaging.

This work was funded through GitHub Sponsors.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-09-30 17:34:03 +10:00
Matt Trentini
bdbc44474f rp2/boards/WEACTSTUDIO: Add WEACTSTUDIO with multiple variants.
This supports 2, 4, 8 and 16MB flash variants.
2022-09-26 12:40:14 +10:00
Matt Trentini
0bc1d10557 rp2/Makefile: Add support for BOARD_VARIANTS.
Following stm32.  This allows a single board definition to define variants
of its configuration.
2022-09-26 12:38:58 +10:00
Jim Mussared
94beeabd2e py/obj: Convert make_new into a mp_obj_type_t slot.
Instead of being an explicit field, it's now a slot like all the other
methods.

This is a marginal code size improvement because most types have a make_new
(100/138 on PYBV11), however it improves consistency in how types are
declared, removing the special case for make_new.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-09-19 19:06:15 +10:00