This changes the freq() and duty_u16() functions to use more simpler, more
accurate formulas, in particular increasing the frequency accuracy from a
few percent to a fraction of a percent in many cases.
Signed-off-by: Paul Grayson <pdg@alum.mit.edu>
This commit prevents the device from "hanging" when using lightsleep while
the WiFi chip is active.
Whenever the WiFi chip wants to interrupt the microcontroller to notify it
for a new package, it sets the CYW43_PIN_WL_HOST_WAKE pin to high,
triggering an IRQ. However, as polling the chip cannot happen in an
interrupt handler, it subsequently notifies the pendsv-service to do a poll
as soon as the interrupt handler ended. In order to prevent a new
interrupt from happening immediately afterwards, even before the poll has
run, the IRQ handler disables interrupts from the pin.
The first problem occurs, when a WiFi package arrives while the main loop
is in cyw43-code. In order to prevent concurrent access of the hardware,
the network code blocks pendsv from running again while entering lwIP code.
The same holds for direct cyw43 code (like changing the cyw43-gpios, i.e.
the LED on the Pico W). While the pendsv is disabled, interrupts can still
occur to schedule a poll (and disable further interrupts), but it will not
run. This can happen while the microcontroller is anywhere in rp2040 code.
In order to preserve power while waiting for cyw43 responses,
cyw43_configport.h defines CYW43_DO_IOCTL_WAIT and
CYW43_SDPCM_SEND_COMMON_WAIT to __WFI(). While this might work in most
cases, there are 2 edge cases where it fails:
- When an interrupt has already been received by the cyw43 stack, for
example due to an incoming ethernet packet.
- When the interrupt from the cyw43 response comes before the
microcontroller entered the __WFI() instruction.
When that happens, wfi will just block forever as no further interrupts are
received. The only way to safely use wfi to wake up from an interrupt is
inside a critical section, as this delays interrupts until the wfi is
entered, possibly resuming immediately until interrupts are reenabled and
the interrupt handler is run. Additionally this critical section needs to
check whether the interrupt has already been disabled and pendsv was
triggered, as in such a case, wfi can never be woken up, and needs to be
skipped, because there is already a package from the network chip waiting.
Note that this turns cyw43_yield into a nop (and thereby the cyw43-loops
into busy waits) from the second time onwards, as after the first call, a
pendsv request will definitely be pending. More logic could be added, to
explicitly enable the interrupt in this case.
Regarding lightsleep, this code has a similar problem. When an interrupt
occurs during lightsleep, the IRQ and pendsv handler and thereby poll are
run immediately, with the clocks still disabled, causing the SPI transfers
to fail. If we don't want to add complex logic inside the IRQ handler we
need to protect the whole lightsleep procedure form interrupts with a
critical section, exiting out early if an interrupt is pending for whatever
reason. Only then we can start to shut down clocks and only enable
interrupts when the system is ready again. Other interrupt handlers might
also be happy, that they are only run when the system is fully operational.
Tested on a Pico W, calling machine.lightsleep() within an endless loop and
pinging from the outside.
This was previously implemented by adding additional members to the
mp_obj_type_t defined for each NIC, which is difficult to do cleanly with
the new object type slots mechanism. The way this works is also not
supported on GCC 8.x and below.
Instead replace it with the type protocol, which is a much simpler way of
achieving the same thing.
This affects the WizNet (in non-LWIP mode) and Nina NIC drivers.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
App the mp_ prefix to usbd_ symbols and files which are defined here and
not in TinyUSB.
rp2 only for now. This includes some groundwork for dynamic USB devices
(defined in Python).
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This commit executes __WFI() on core 0 only to avoid core1 locking up since
it doesn't enable any interrupts by default (except for `SIO_IRQ_PROC1`).
This fixes a lockup when calling `cyw43_do_ioctl` from core1.
Fixes issue #9597.
If USB CDC is connected and the board sends data, but the host does not
receive the data, the device locks up. This is fixed in this commit by
having a timeout of 500ms, after which time the transmission is skipped.
Fixes issue #9634.
This is necessary to access sites that only support these protocols.
The rp2 port already has ECDH enabled, so this just adds ECDSA there. The
other ports now gain both ECDH and ECDSA. The code size increase is:
- rp2 (PICO_W): +2916 bytes flash, +24 bytes BSS
- stm32 (PYBD_SF6): +20480 bytes flash, +32 bytes data, +48 bytes BSS
- mimxrt (TEENSY41): +20708 bytes flash, +32 bytes data, +48 bytes BSS
- unix (standard x86-64): +39344 executable, +1744 bytes data, +96 BSS
This is obviously a large increase in code size. But there doesn't seem to
be any other option because without elliptic curve cryptography devices are
partially cut off from the internet. For use cases that require small
firmware size, they'll need to build custom firmware with a custom mbedtls
config.
Signed-off-by: Damien George <damien@micropython.org>
Updates all README.md and docs, and manifests to `require("mip")`.
Also extend and improve the documentation on freezing and packaging.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Instead of being an explicit field, it's now a slot like all the other
methods.
This is a marginal code size improvement because most types have a make_new
(100/138 on PYBV11), however it improves consistency in how types are
declared, removing the special case for make_new.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The goal here is to remove a slot (making way to turn make_new into a slot)
as well as reduce code size by the ~40 references to mp_identity_getiter
and mp_stream_unbuffered_iter.
This introduces two new type flags:
- MP_TYPE_FLAG_ITER_IS_ITERNEXT: This means that the "iter" slot in the
type is "iternext", and should use the identity getiter.
- MP_TYPE_FLAG_ITER_IS_CUSTOM: This means that the "iter" slot is a pointer
to a mp_getiter_iternext_custom_t instance, which then defines both
getiter and iternext.
And a third flag that is the OR of both, MP_TYPE_FLAG_ITER_IS_STREAM: This
means that the type should use the identity getiter, and
mp_stream_unbuffered_iter as iternext.
Finally, MP_TYPE_FLAG_ITER_IS_GETITER is defined as a no-op flag to give
the default case where "iter" is "getiter".
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
I.e. for whichever SPI/I2C instance is PICO_DEFAULT_I2C, there's no need to
set MICROPY_HW_SPIn_SCK.
The only ones remaining are for the non-default instance.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
In most cases, it's calculated automatically from the board name, and so
doesn't need to be set at all.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Changes in this commit:
- Manifest include's now use the directory path where possible (no longer
necessary to include the manifest.py file explicitly).
- Add manifest.py for all drivers and components that are referenced by
port/board manifests.
- Replace all uses of freeze() with package()/module(), except for port and
board modules.
- Use opt=3 everywhere, for consistency and to reduce code size.
- Use require() instead of include() for all micropython-lib references.
- Remove support for optional board-level manifest.py in mimxrt port, to
make it behave the same as other ports (the board must set
FROZEN_MANIFEST to a custom manifest.py, which can optionally include the
default, port-level manifest).
- Also reinstates modules that were accidentally removed from the esp8266
512k build in fbe9417b90.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Signed-off-by: Damien George <damien@micropython.org>
micropython-lib is now a submodule, and the manifest compilation process
will ensure it is available, so manifests no longer need to check that it
is available.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
uart.flush()
flush() will wait until all characters have been sent. It may return
while the last character is sent. if needed, the calling code has to
add one character wait time. To avoid a permanent lock, a timeout
applies depending on the size of txbuf and the baud rate.
ret = uart.txdone()
ret is True if no transfer is in progress. It may return True if the
last byte of a transfer is sent.
ret is False otherwise.
Previously the desired output type was specified. Now make the type part
of the function name. Because this function is used in a few places this
saves code size due to smaller call-site.
This makes `mp_obj_new_str_type_from_vstr` a private function of objstr.c
(which is almost the only place where the output type isn't a compile-time
constant).
This saves ~140 bytes on PYBV11.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Figure out path to arm-none-eabi-size the same way it's done for the
other binaries, instead of assuming it to be in the user's $PATH.
Signed-off-by: Jacob Siverskog <jacob@teenage.engineering>
Create a new linker section .unitialized_bss for bss that does not need
zero-initialising.
Move gc_heap to this section, which saves ~30ms from rising edge of RESET
to setting a pin HIGH in MicroPython.
Zero fill happens in Pico SDK crt0.S before ROSC is configured. It's very,
very slow.
Signed-off-by: Phil Howard <phil@gadgetoid.com>
The ntptime module was previously only included in the ESP8266 port. This
commit factors that module out into the extmod directory, makes it support
different epochs, and includes it in the rp2 port.
Used to be special-cased for Pico, but now everything depends on
micropython-lib if it's using a frozen manifest.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Still see some USB issues apparently caused by delays loading wifi
firmware. cyw43_delay_ms is used to wait in the driver, so we should call
the event hook in there.
Fixes#8963.
The state machines were not properly restarted in the case that the same
PIO program was shared among multiple StateMachine instances. This is
because only the first StateMachine to use the program would set the
rp2_state_machine_initial_pc variable.
See https://forum.micropython.org/viewtopic.php?f=21&t=12776&p=69464#p69464
Originally in drivers/ninaw10/nina_wifi_bsp.c but that isn't a QSTR source.
Also remove outdated commment about root pointers in mpconfigport.h.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This is a statically-allocated UART (see machine_uart.c), and doesn't
contain any heap pointers other than the ringbufs (which are already root
pointers), so no need to track it additionally.
Saves needing to add mpbthciport.c to the QSTR sources.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
