* Use R_SCI_UART_BaudCalculate() of fsp/src/r_sci_uart/r_sci_uart.c
* Support UART.init(baudrate)
Signed-off-by: Takeo Takahashi <takeo.takahashi.xv@renesas.com>
The config header files with the same name have the same contents, so they
don't need to be repeated for each board in the board's source directory.
Signed-off-by: Damien George <damien@micropython.org>
IDF v5.0 provides access to rssi value for received espnow packets via
recv_info arg to recv_cb().
Signed-off-by: Glenn Moloney <glenn.moloney@gmail.com>
This commit updates the esp32 port to work exclusively with ESP-IDF v5.
IDF v5 is needed for some of the newer ESP32 SoCs to work, and it also
cleans up a lot of the inconsistencies between existing SoCs (eg S2, S3,
and C3).
Support for IDF v4 is dropped because it's a lot of effort to maintain both
versions at the same time.
The following components have been verified to work on the various SoCs:
ESP32 ESP32-S2 ESP32-S3 ESP32-C3
build pass pass pass pass
SPIRAM pass pass pass N/A
REPL (UART) pass pass pass pass
REPL (USB) N/A pass pass N/A
filesystem pass pass pass pass
GPIO pass pass pass pass
SPI pass pass pass pass
I2C pass pass pass pass
PWM pass pass pass pass
ADC pass pass pass pass
WiFi STA pass pass pass pass
WiFi AP pass pass pass pass
BLE pass N/A pass pass
ETH pass -- -- --
PPP pass pass pass --
sockets pass pass pass pass
SSL pass ENOMEM pass pass
RMT pass pass pass pass
NeoPixel pass pass pass pass
I2S pass pass pass N/A
ESPNow pass pass pass pass
ULP-FSM pass pass pass N/A
SDCard pass N/A N/A pass
WDT pass pass pass pass
Signed-off-by: Damien George <damien@micropython.org>
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This function was made private/static in IDF commit
c67f4c2b4c2bb4b7740f988fc0f8a3e911e56afe, so it add back here.
Signed-off-by: Damien George <damien@micropython.org>
Mostly updates comments, but also renames the UASYNCIO enum value to
ASYNCIO.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The asyncio module now has much better CPython compatibility and
deserves to be just called "asyncio".
This will avoid people having to write `from uasyncio import asyncio`.
Renames all files, and updates port manifests to use the new path. Also
renames the built-in _uasyncio to _asyncio.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Commit c046b23ea2 prevented frozen boot code
from being interrupted by Ctrl-C, but that means a corrupt filesystem will
forever lock up an esp32/esp8266 board. This commit fixes that by
explicitly enabling Ctrl-C before running the forever loop.
Signed-off-by: Damien George <damien@micropython.org>
This commit adds initial support for STM32H5xx MCUs. The following
features have been confirmed to be working on an STM32H573:
- UART over REPL and USB CDC
- USB CDC and MSC
- internal flash filesystem
- machine.Pin
- machine.SPI transfers with DMA
- machine.ADC
- machine.RTC
- pyb.LED
- pyb.Switch
- pyb.rng
- mboot
Signed-off-by: Damien George <damien@micropython.org>
The G0 USB peripheral behaves more like MICROPY_HW_USB_IS_MULTI_OTG=0 than
that config =1. This fixes the configuration of the PMA FIFO buffers.
Signed-off-by: Damien George <damien@micropython.org>
For debugging purposes, to see output from other peripherals.
Also reset the pyb_stdio_uart state at the end of soft reset, in case it
points to a heap-allocated object.
Signed-off-by: Damien George <damien@micropython.org>
This change enables the ULP (FSM) for all ESP32 variants rather than
requiring it to be enabled for each board specifically.
It also ensures the correct header file is included for each variant.
Lastly, it updates the IDF version we're builing against to v4.4.2, as that
version contains important fixes to make the ULP actually work on S2/S3
chips. See: https://github.com/espressif/esp-idf/commit/a0e3d48
Signed-off-by: Wilko Nienhaus <wilko.nienhaus@gmail.com>
In 5fe2a3f1 the ESP32 port underwent a change to how `MICROPY_PORT_DIR`
is defined. This commit normalizes the `rp2` port to use the same
underlying variable mechanism (`CMAKE_CURRENT_LIST_DIR`).
Signed-off-by: Brian 'redbeard' Harrington <redbeard@dead-city.org>
This migrates the CMake variable `MICROPY_PORT_DIR` from the ESP-IDF
defined project to the component. Previously used instances of the variable
within the project definition have been migrated to
`CMAKE_CURRENT_LIST_DIR`. Within the component (the `main` subdirectory in
the ESP32 port) we define `MICROPY_PORT_DIR` using `CMAKE_CURRENT_LIST_DIR`
and subsequently use the `MICROPY_PORT_DIR` value in all locations where
`PROJECT` had previously been used.
Context:
In commit 9b90882146, initial support was added for building with the newly
introduced CMake support provided by the ESP-IDF.
Specifically, the commit message states:
> This commit adds support for building the esp32 port with CMake, and in
particular, it builds MicroPython as a component within the ESP-IDF. Using
CMake and the ESP-IDF build infrastructure makes it much easier to maintain
the port, especially with the various new ESP32 MCUs and their required
toolchains.
`PROJECT_DIR` is a variable populated by the ESP-IDF specifically and is
not stable when used with "[Pure CMake components][1]" as documented in the
ESP-IDF. It is intended to be used in the scope of the parent of the
current file (the "project") as opposed to the current file ("the
component"). Crossing into the parent scope like this works solely when the
"project" is MicroPython, but not when used as a component by other ESP-IDF
projects.
Analyzing this file, the intention is to reference the "Project" which in
the example is the parent directory. Within the [CMake variables][2]
documentation, there is one specifically defined for referencing the
directory for the CMake listfile currently being processed:
[`CMAKE_CURRENT_LIST_DIR`][3].
After making the change from `PROJECT_DIR` to `CMAKE_CURRENT_LIST_DIR`, the
reach into the parent scope defined by the ESP-IDF and the resulting CMake
interface violation is removed.
Similar to the component definition, the project `CMakeLists.txt` uses the
variable `CMAKE_SOURCE_DIR` which CMake defines as "The path to the top
level of the source tree." This commit changes the variable to
`CMAKE_CURRENT_LIST_DIR` for the reasons cited above.
[1]: https://docs.espressif.com/projects/esp-idf/en/latest/esp32s2/api-guides/build-system.html#writing-pure-cmake-components
[2]: https://cmake.org/cmake/help/latest/manual/cmake-variables.7.html
[3]: https://cmake.org/cmake/help/latest/variable/CMAKE_CURRENT_LIST_DIR.html
Signed-off-by: Brian 'redbeard' Harrington <redbeard@dead-city.org>
Following how mkrules.cmake works. This makes it easy for a port to enable
frozen code, by defining FROZEN_MANIFEST in its Makefile.
Signed-off-by: Damien George <damien@micropython.org>
This is a MicroPython-specific module that existed to support the old
version of uasyncio. It's undocumented and not enabled on all ports and
takes up code size unnecessarily.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Applies to drivers/examples/extmod/port-modules/tools.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Previously sys.path could be modified by append/pop or slice assignment.
This allows `sys.path = [...]`, which can be simpler in many cases, but
also improves CPython compatibility.
It also allows sys.path to be set to a tuple which means that you can
clear sys.path (e.g. temporarily) with no allocations.
This also makes sys.path (and sys.argv for consistency) able to be disabled
via mpconfig. The unix port (and upytesthelper) require them, so they
explicitly verify that they're enabled.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Otherwise you can get into the confusing state where e.g. sys.ps1 is
enabled in config (via `MICROPY_PY_SYS_PS1_PS2`) but still doesn't actually
get enabled.
Also verify that the required delegation options are enabled in modsys.c.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Updates any includes, and references from Makefiles/CMake.
This essentially reverts what was done long ago in commit
136b5cbd76
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
In order to keep "import umodule" working, the existing mechanism is
replaced with a simple fallback to drop the "u".
This makes importing of built-ins no longer touch the filesystem, which
makes a typical built-in import take ~0.15ms rather than 3-5ms.
(Weak links were added in c14a81662c)
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This renames the builtin-modules, such that help('modules') and printing
the module object will show "module" rather than "umodule".
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The QSPI driver provides the interface for using an on-board QSPI flash for
the filesystem. It provides the same methods as the driver for the
internal flash and uses the same name. Therefore, only one of the drivers
for internal flash, SPI flash and QSPI flash must be enabled at a time.
Signed-off-by: robert-hh <robert@hammelrath.com>
The SPI flash driver includes the block device for being used as a
filesystem. It provides the same methods as the driver for the internal
flash.
Signed-off-by: robert-hh <robert@hammelrath.com>
For SAMD21 devices, the board flash signals must be named in pins.csv as
FLASH_MOSI, FLASH_MISO, FLASH_SCK, FLASH_CS for creating the SPI object.
And rename the QSPI pins to QSPI_xxxx instead of FLASH_xxx.
Signed-off-by: robert-hh <robert@hammelrath.com>
Updates all `help()` output to use the phrase:
`For online docs please visit http://docs.micropython.org/`
Some ports previously used different wording, some pointed to the wrong
link. Also make all ports use `help.c` for consistency.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This makes it so that sub-packages are resolved relative to their parent's
`__path__`, rather than re-resolving each parent's filesystem path.
The previous behavior was that `import foo.bar` would first re-search
`sys.path` for `foo`, then use the resulting path to find `bar`.
For already-loaded and u-prefixed modules, because we no longer need to
build the path from level to level, we no longer unnecessarily search
the filesystem. This should improve startup time.
Explicitly makes the resolving process clear:
- Loaded modules are returned immediately without touching the filesystem.
- Exact-match of builtins are also returned immediately.
- Then the filesystem search happens.
- If that fails, then the weak-link handling is applied.
This maintains the existing behavior: if a user writes `import time` they
will get time.py if it exits, otherwise the built-in utime. Whereas `import
utime` will always return the built-in.
This also fixes a regression from a7fa18c203
where we search the filesystem for built-ins. It is now only possible to
override u-prefixed builtins. This will remove a lot of filesystem stats
at startup, as micropython-specific modules (e.g. `pyb`) will no longer
attempt to look at the filesystem.
Added several improvements to the comments and some minor renaming and
refactoring to make it clearer how the import mechanism works. Overall
code size diff is +56 bytes on STM32.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This one sets the flash image length properly for the teensy loader, such
that the file system is not erased. It was already set in commit
8e54225140 but got lost when the MIMXRT1176
board was added.
Signed-off-by: robert-hh <robert@hammelrath.com>
Three bugs have been fixed in this commit:
1. When the duty was set with duty_u16(), changing the freq with pwm.freq()
would not keep relative duty rate, but the absolute pulse duration.
2. Fix another inconsistency when displaying the PWM pin's properties of a
QTMR channel.
3. Improve the error checks for the second channel being a PWM pin and pin
pairs to be a FLEXPWM A/B pair.
Signed-off-by: robert-hh <robert@hammelrath.com>
These have by default FAT support. The SAMD21 build does not support FAT.
The nrf port also implements os.sync(), but has it's own copy of moduos.c.
Code size increases seen: 40 to 56 bytes.
Signed-off-by: robert-hh <robert@hammelrath.com>
The hal_entry.c code is duplicated across all boards, so consolidate it to
a common ra_hal.c file. And remove the hal_entry() function because it
simply calls main().
Signed-off-by: Damien George <damien@micropython.org>
Also fix MAX_ENDPOINT definition for G0, which follows G4.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
By specifying rts=pin(x) and/or cts=Pin(x) in the constructor. The pad
numbers for the UART pins are fix in this case: TX must be at pad 0, RX at
pad 1, RTS at pad 2 and CTS at pad 3.
repr(uart) shows the pin names for rts and cts, if set. In case of a RX
overflow, the rx interrupt will be disabled instead of just discarding the
data. That allows RTS to act.
If RTS is inactive, still 2 bytes can be buffered in the FIFO.
Signed-off-by: robert-hh <robert@hammelrath.com>
With Crystal: set the crystal startup wait time to 1 second. It was 2
seconds before, and that seeemed too long.
With USB-Sync: scan for up to 1 second for the USB to be registered and
carry on with boot as soon as it it. Before, the code just waited for
500ms.
Side change: improve related comments.
Signed-off-by: robert-hh <robert@hammelrath.com>
These include ADC, DAC, I2C, SoftI2C, SPI, SoftI2C, PWM, UART, pulse. This
is useful for devices like the Adafruit Trinket series which have almost no
accessible GPIO pins.
Signed-off-by: robert-hh <robert@hammelrath.com>
If sockets were open when calling soft reset, gc_sweep_all() would try to
close them. In case of e.g. the NINA WiFi handler, connected through SPI,
spi_transfer() would be called for command exchange with the NINA module.
But at that time SerCom was already disabled.
Moving sercom_deinit_all() behind gc_sweep_all() solves this issue.
Signed-off-by: robert-hh <robert@hammelrath.com>
Such that they are easier to adapt. The maximum code size is set by:
MICROPY_HW_CODESIZE=xxxK
in mpconfigmcu.mk for the MCU family as default or in mpconfigboard.mk for
a specific board. Setting the maximum code size allows the loader to error
out if the code gets larger than the space dedicated for it.
Signed-off-by: robert-hh <robert@hammelrath.com>
Change UART clock source on S3/C3 so the UART can operate when CPU
frequency is below 80MHz. This allows the UART to remain operational when
using Dynamic Frequency Scaling (DFS).
Signed-off-by: Patrick Joy <patrick@joytech.com.au>
This commit enables the ULP for the S2 and S3 chips.
Note this is the FSM (Finite State Machine) ULP.
Signed-off-by: Patrick Joy <patrick@joytech.com.au>
Once all the firmware has been flashed and the final signatures checked,
mboot writes the "all good" byte into the header of the application. This
step uses the buffer firmware_head which, if unaligned in the build, fails
when cast to a uint64_t* in flash.c.
Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au>
These were incorrectly added in d995c01042.
The fix here includes the full differential ADC definitions.
Signed-off-by: brave ulysses <brave_ulysses@email.com>
When the network module was first introduced in the esp8266 port in
ee3fec3167 there was only one interface (STA)
and, to save flash, the WLAN object was aliased to the network module,
which had just static methods for WLAN operations. This was subsequently
changed in 9e8396accb when the AP interface
was introduced, and the WLAN object became a true class.
But, network.WLAN remained a function that returned either the STA or AP
object and was never upgraded to the type itself. This scheme was then
copied over to the esp32 port when it was first introduced.
This commit changes network.WLAN from a function to a reference to the WLAN
type. This makes it consistent with other ports and network objects, and
allows accessing constants of network.WLAN without creating an instance.
Signed-off-by: Damien George <damien@micropython.org>
Building the Pico-W needs the MICROPY_PY_NETWORK_CYW43 flag to be set in
order to include building the CYW43 Wifi driver. But then mp_hal_get_mac()
handles the MAC assignment for all nics the "CYW43 way", copying the real
MAC provided by the WiFi hardware. This will fail for all other NIC types,
resulting in an invalid MAC address.
The solution in this commit is to add a check for the NIC type parameter
idx and handle the MAC address respectively.
Convert to an absolute path to always reliably locate manifest.py. This is
already done in Makefile, but is also needed in CMakeLists.txt if cmake is
invoked directly.
Signed-off-by: Phil Howard <phil@pimoroni.com>
Currently rp2.StateMachine.exec(instr_in) requires that the instr_in
parameter be a string representing the PIO assembly language instruction
to be encoded by rp2.asm_pio_encode(). This commit allows the parameter
to also be of integral type. This is useful if the exec() method is
being called often where the use of pre-encoded machine code is
desireable.
This commit still supports calls like:
sm.exec("set(0, 1)")
It also now supports calls like:
# Performed once earlier, maybe in __init__()
assembled_instr = rp2.asm_pio_encode("out(y, 8)", 0)
# Performed multiple times later as the PIO state machine is
# configured for its next run.
sm.exec(assembled_instr)
The existing examples/rp2/pio_exec.py and examples/rp2/pio_pwm.py that
exercise the rp2.StateMachine.exec() method still work with this change.
Signed-off-by: Adam Green <adamgrym@yahoo.com>
FSP v4.4.0 refers to CMSIS V5.4.1, and __COMPILER_BARRIER() is used in bsp.
On the other hand, lib/cmsis is V5.1.0 and the macro is not defined.
Therefore, compile error happens.
As the workaround, the macro definition is added.
If lib/cmsis is updated in the future, this addition can be removed.
Signed-off-by: Takeo Takahashi <takeo.takahashi.xv@renesas.com>
This modifies the windows port Makefile to use += for QSTR_DEFS and
QSTR_GLOBAL_DEPENDENCIES so that variants can add additional files if
needed (similar to stm32 port).
Signed-off-by: David Lechner <david@pybricks.com>
This modifies the unix port Makefile to use += for QSTR_DEFS and
QSTR_GLOBAL_DEPENDENCIES so that variants can add additional files if
needed (similar to stm32 port).
Signed-off-by: David Lechner <david@pybricks.com>
It was treated as an error before. The error surfaced when using the
NINAW10 drivers for WiFi support. Even if this is a bad behavior of the
NINA driver, machine_spi can be forgiving in that situation.
Separate low level flash access from mimxrt flash driver object. Allows
better abstraction from hardware for testing and reuse in other areas (e.g.
bootloader).
Signed-off-by: Philipp Ebensberger <philipp.ebensberger@3bricks-software.de>
For esp32 and esp8266 this commit adds:
- a 'pm' option to WLAN.config() to set/get the wifi power saving mode; and
- PM_NONE, PM_PERFORMANCE and PM_POWERSAVE constants to the WLAN class.
This API should be general enough to use with all WLAN drivers.
Documentation is also added.
All ports that enable MICROPY_PY_MACHINE_PWM now enable these two
sub-options, so remove these sub-options altogether to force consistency in
new ports that implement machine.PWM.
Signed-off-by: Damien George <damien@micropython.org>
Changes in this commit:
- Limit duty_u16() to 65535 and duty_ns() to the period duration.
- Return 0 for pwm.freq() if the frequency has not been set yet.
- Return 0 for pwm.duty_us16() and duty_ns() unless both frequency and
duty cycle have been set.
- Initialize the pin to PWM at the very end of the constructor, to avoid
possible glitches on the pin when setting up the PWM.
This adds support for freq/duty_u16/duty_ns keyword arguments in the PWM
constructor, and adds the PWM.init() method. Using init() without
arguments enables a previously deinit-ed PWM again.
Further changes in this commit:
- Do not start PWM output if only duty was set.
- Stop all PWM slices on soft-reset.
- Fix a bug when changing the freq on a channel pair with duty_ns set.
The PWM.init() method has been added. Calling init() without arguments
restarts a PWM channel stopped with deinit(). Otherwise single parameters
except for "device=n" can be changed again. The device can only be
specified once, either in the constructor or the first init() call.
Also simplify get_pwm_config() and get_adc_config(), and shrink the PWM
object.
And also fix/improve the following:
- Simplify the duty handling a little bit.
- Allow duty_u16(65536), which sets the output high.
- Rename machine_pwm_start() to mp_machine_pwm_start(), in preparation for
a possible start/stop method pair.
This fixes:
- type-comparison (E721): do not compare types, use isinstance().
- string-dot-format-missing-arguments (F524): .format call is missing
argument(s) for placeholder(s): {message}.
- f-string-missing-placeholders (F541).
- is-literal (F632): Use != to compare constant literals.
The last one is fixed by just comparing for truthfulness of `state`.
ESP-NOW is a proprietary wireless communication protocol which supports
connectionless communication between ESP32 and ESP8266 devices, using
vendor specific WiFi frames. This commit adds support for this protocol
through a new `espnow` module.
This commit builds on original work done by @nickzoic, @shawwwn and with
contributions from @zoland. Features include:
- Use of (extended) ring buffers in py/ringbuf.[ch] for robust IO.
- Signal strength (RSSI) monitoring.
- Core support in `_espnow` C module, extended by `espnow.py` module.
- Asyncio support via `aioespnow.py` module (separate to this commit).
- Docs provided at `docs/library/espnow.rst`.
Methods available in espnow.ESPNow class are:
- active(True/False)
- config(): set rx buffer size, read timeout and tx rate
- recv()/irecv()/recvinto() to read incoming messages from peers
- send() to send messages to peer devices
- any() to test if a message is ready to read
- irq() to set callback for received messages
- stats() returns transfer stats:
(tx_pkts, tx_pkt_responses, tx_failures, rx_pkts, lost_rx_pkts)
- add_peer(mac, ...) registers a peer before sending messages
- get_peer(mac) returns peer info: (mac, lmk, channel, ifidx, encrypt)
- mod_peer(mac, ...) changes peer info parameters
- get_peers() returns all peer info tuples
- peers_table supports RSSI signal monitoring for received messages:
{peer1: [rssi, time_ms], peer2: [rssi, time_ms], ...}
ESP8266 is a pared down version of the ESP32 ESPNow support due to code
size restrictions and differences in the low-level API. See docs for
details.
Also included is a test suite in tests/multi_espnow. This tests basic
espnow data transfer, multiple transfers, various message sizes, encrypted
messages (pmk and lmk), and asyncio support.
Initial work is from https://github.com/micropython/micropython/pull/4115.
Initial import of code is from:
https://github.com/nickzoic/micropython/tree/espnow-4115.
This allows updating mp_mbedtls_errors.c for the other mbedtls based ports
based on mbedTLS v2.28.1. This esp32-specific file will not be required
after updating IDF support to >= v4.4.1.
Signed-off-by: Carlos Gil <carlosgilglez@gmail.com>
API change: time.time_ns() is added, but it just returns 0.
No API or functional change to existing time functions.
Signed-off-by: Damien George <damien@micropython.org>
API additions;
- time.sleep() is added
- time.ticks_cpu() is added, but it just returns 0
No API or functional change to existing time functions.
Signed-off-by: Damien George <damien@micropython.org>
API change: time.time_ns() is added, but it just returns 0.
No API or functional change to existing time functions.
Signed-off-by: Damien George <damien@micropython.org>
Based on extmod/utime_mphal.c, with:
- a globals dict added
- time.localtime wrapper added
- time.time wrapper added
- time.time_ns function added
New configuration options are added for this module:
- MICROPY_PY_UTIME (enabled at basic features level)
- MICROPY_PY_UTIME_GMTIME_LOCALTIME_MKTIME
- MICROPY_PY_UTIME_TIME_TIME_NS
Signed-off-by: Damien George <damien@micropython.org>
Changes in this commit:
- Change MICROPY_HW_BOARD_NAME definition to match the product name.
- Rename board folder's name to match the product name style.
- Change related files like Makefile, document descriptions, test cases, CI
and tools.
Signed-off-by: Takeo Takahashi <takeo.takahashi.xv@renesas.com>
Since c80e7c14e6 changed the GC heap to use
all unused RAM, there is no longer any RAM available for the traditional C
heap (which is not used by default in MicroPython but may be used by C
extensions). This commit adds a provision for a board to reserve RAM for
the C heap, by defining MICROPY_C_HEAP_SIZE.
Signed-off-by: Damien George <damien@micropython.org>
The previous code worked on ESP32 but not ESP32-S3. All the IDF (v4.4.3)
examples call rmt_set_tx_loop_mode before rmt_write_items, so make that
change here.
Signed-off-by: Damien George <damien@micropython.org>
- Use HCI_TRACE macro consistently.
- Use the same colour formatting.
- Add a tool to convert to .pcap for Wireshark.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This adds a mechanism to track a pending notify/indicate operation that
is deferred due to the send buffer being full. This uses a tracked alloc
that is passed as the content arg to the callback.
This replaces the previous mechanism that did this via the global pending
op queue, shared with client read/write ops.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Makes gatts_notify and gatts_indicate work in the same way: by default they
send the DB value, but you can manually override the payload.
In other words, makes gatts_indicate work the same as gatts_notify.
Note: This removes support for queuing notifications and indications on
btstack when the ACL buffer is full. This functionality will be
reimplemented in a future commit.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit adds support for the `timeout` keyword argument to machine.I2C
on the rp2 port, following how it's done on other ports.
The main motivation here is avoid the interpreter crashing due to infinite
loops when SDA is stuck low, which is quite common if the board gets reset
while reading from an I2C device.
A default timeout of 50ms is chosen because it's consistent with:
- Commit a707fe50b0 which used a timeout of
50,000us for zero-length writes on the rp2 port.
- The machine.SoftI2C class which uses 50,000us as the default timeout.
- The stm32 port's hardware I2C, which uses 50,000us for
I2C_POLL_DEFAULT_TIMEOUT_US.
This commit also fixes the default timeout on the esp32 port to be
consistent with the above, and updates the documentation for machine.I2C to
document this keyword argument.
If a board defines a custom bootloader entry function it will be called
first, if not and the ROM API supports RUN bootloader API, then
`machine.bootloader()` will jump to the ROM serial downloader in USB mode.
This commit allows boards to disable Ethernet and keep the networking stack
enabled, to use an alternate networking interface, such as WiFi.
Note that the `network` and `socket` modules are now enabled by default for
a board.
This commit is necessary to make MicroPython work on this eval kit out of
the box, as the eval kit ships with the HyperFlash physically disconnected
from the bus (refer to the schematics or the user guide) and the QSPI
connected instead, but the fuses/board/pins are configured to boot from
internal flash (on FlexSPI2).
Note that enabling the HyperFlash is not trivial, as it requires soldering
and desoldering of many small footprint resistors and changing fuses.
Helps prevent the filesystem from getting formatted by mistake, among other
things. For example, on a Pico board, entering Ctrl+D and Ctrl+C fast many
times will eventually wipe the filesystem (without warning or notice).
Further rationale: Ctrl+C is used a lot by automation scripts (eg mpremote)
and UI's (eg Mu, Thonny) to get the board into a known state. If the board
is not responding for a short time then it's not possible to know if it's
just a slow start up (eg in _boot.py), or an infinite loop in the main
application. The former should not be interrupted, but the latter should.
The only way to distinguish these two cases would be to wait "long enough",
and if there's nothing on the serial after "long enough" then assume it's
running the application and Ctrl+C should break out of it. But defining
"long enough" is impossible for all the different boards and their possible
behaviour. The solution in this commit is to make it so that frozen
start-up code cannot be interrupted by Ctrl+C. That code then effectively
acts like normal C start-up code, which also cannot be interrupted.
Note: on the stm32 port this was never seen as an issue because all
start-up code is in C. But now other ports start to put more things in
_boot.py and so this problem crops up.
Signed-off-by: David Grayson <davidegrayson@gmail.com>
The dispatch active flag is only set once and never reset, so it will
always call the dispatch handler (once enabled), and it's not really
needed because it doesn't make things more efficient.
Also remove unused included headers.
Changes in this commit:
- Move the pwm_seq array to the p_config data structure. That prevents
potential resource collisions between PWM devices.
- Rename the keyword argument 'id' to 'device'. That's consistent with the
SAMD port as the other port allowing to specify it.
This is a best-effort implementation of write polling. It's difficult to
do correctly because if there are multiple output streams (eg UART and USB
CDC) then some may not be writeable while others are. A full solution
should also have a return value from mp_hal_stdout_tx_strn(), returning the
number of bytes written to the stream(s). That's also hard to define.
The renesas-ra and stm32 ports already implement a similar best-effort
mechanism for write polling.
Fixes issue #11026.
Signed-off-by: Damien George <damien@micropython.org>
Prior to this change, setting of UART parameters like parity, stop bits or
data bits did not work correctly. As suggested by @iabdalkader, adding
__DSB() fixes the problem, making sure that changes to the UART LCR_H
register are seen by the peripheral.
Note: the FIFO is already enabled in the call to uart_init(), so the call
to uart_set_fifo_enabled() is not required, but kept for visibility.
Fixes issue #10976.
The following have been tested and are working:
- 550MHz CPU frequency
- UART REPL via ST-Link
- USB REPL and mass storage
- 3x LEDs and 1x user button
- Ethernet
Signed-off-by: Damien George <damien@micropython.org>
For builds with DEBUG=1 and MICROPY_HW_ENABLE_UART_REPL=1, calling
stdio_init_all() in main() detaches the UART input from REPL. This change
suppresses calling stdio_init_all() then.
Previously, setting MICROPY_HW_ENABLE_USBDEV to 0 caused build errors. The
change affects the nrf and samd ports as well, so MICROPY_HW_ENABLE_USBDEV
had to be explicitly enabled there.
The configuration options MICROPY_HW_ENABLE_USBDEV and
MICROPY_HW_ENABLE_UART_REPL are independent, and can be enabled or disabled
by a board.
Signed-off-by: Damien George <damien@micropython.org>
Changes in this commit:
- Add the timeout and timeout_char keyword options.
- Make uart.read() non-blocking.
- Add uart.any().
- Add ioctl MP_STREAM_POLL handling.
- Change uart.write() into non-busy waiting. uart.write() still waits until
all data has been sent, but calls MICROPY_EVENT_POLL_HOOK while waiting.
uart.write() uses DMA for transfer. One option would be to add a small
local buffer, such that transfers up to the size of the buffer could be
done without waiting.
- As a side effect to the change of uart.write(), uart.txdone() and ioctl
flush now report/wait correctly for the end of transmission.
- Change machine_hard_uart_buf_t in machine_hard_uart_obj_t to an instance
of that struct, rather than a pointer to one.
Even if boards do not have a clock crystal. In that case, the clock
quality will be very poor.
Always having machine.RTC means that the date/time can be set in a way that
is consistent with other ports.
This commit also removes the special code in modutime.c for devices without
the RTC class.
Signed-off-by: Damien George <damien@micropython.org>
These have the same frequency, but can have different duty cycle and
polarity.
pwm.deinit() stops all channels of a module, but does not release the
module. pwm.init() without arguments restarts all outputs.
Using extmod/machine_pwm.c for the Python bindings and the existing
softpwm.c driver, by just adding the interface.
Properties:
- Frequency range 1-3906 Hz.
- All PWM outputs run at the same frequency but can have different duty
cycles.
- Limited to the P0.x pins.
Since it uses the existing softpwm.c mechanism, it will be affected by
playing music with the music class.
This is a breaking change, making the hardware PWM on the nrf port
compatible with the other ports providing machine.PWM.
Frequency range 4Hz - ~5.4 MHz. The base clock range is 125kHz to 16 MHz,
and the divider range is 3 - 32767.
The hardware supports up to four outputs per PWM device with different duty
cycles, but only one output is (and was) supported.
Borrowing an idea from the mimxrt port (also stm32 port): in the loader
input file memmap_mp.ld calculate __GcHeapStart and __GcHeapEnd as the
unused RAM. Then in main.c use these addresses as arguments to gc_init().
The benefits of this change are:
1) When libraries are added or removed in the future changing BSS usage,
main.c's sizing of the GC heap does not need to be changed.
2) Currently these changes make the GC area about 30 KBytes larger, eg on
PICO_W the GC heap increases from 166016 to 192448 bytes. Without that
change this RAM would never get used.
3) If someone wants to disable one or more SRAM blocks on the RP2040 to
reduce power consumption it will be easy: just change the MEMORY section
in memmap_mp.ld. For instance to not use SRAM2 and SRAM3 change it to:
MEMORY
{
FLASH(rx) : ORIGIN = 0x10000000, LENGTH = 2048k
RAM(rwx) : ORIGIN = 0x21000000, LENGTH = 128k
SCRATCH_X(rwx) : ORIGIN = 0x20040000, LENGTH = 4k
SCRATCH_Y(rwx) : ORIGIN = 0x20041000, LENGTH = 4k
}
Then to turn off clocks for SRAM2 and SRAM3 from MicroPython, set the
appropriate bits in WAKE_EN0 and SLEEP_EN0.
Tested by running the firmware.uf2 file on PICO_W and displaying
micropython.mem_info(). Confirmed GC total size approximately matched the
size calculated by the loader.
Signed-off-by: cpottle9 <cpottle9@outlook.com>
This function seems to work fine in multi-core applications now.
The delay is now in units of microseconds instead of depending on the clock
speed, and is adjustable by board configuration headers.
Also added documentation.
These changes allow the firmware to support both the REV-1 and REV-2
versions of the board:
- Freeze the new device drivers used in REV-2.
- Add a board-level module that abstracts the IMU chipset.
Changes are:
- Freeze micropython-lib time module to get strftime.
- Reserve the last 1MB of QSPI flash for (optional) WiFi firmware storage.
- Disable SD card mount on boot.
- Enable high-speed BLE firmware download.
This is for boards without networking support so that the default boot.py
continues to work.
Also update boot.py to use network.country and network.hostname instead.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This removes the previous WiFi driver from drivers/cyw43 (but leaves behind
the BT driver), and makes the stm32 port (i.e. PYBD and Portenta) use the
new "lib/cyw43-driver" open-source driver already in use by the rp2 port.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Rather than duplicating the implementation of `network`, this allows
ESP8266 to use the shared one in extmod. In particular this gains access
to network.hostname and network.country.
Other than adding these two methods, there is no other user-visible change.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Rather than duplicating the implementation of `network`, this allows ESP32
to use the shared one in extmod. In particular this gains access to
network.hostname and network.country.
Set default hostnames for various ESP32 boards.
Other than adding these two methods and the change to the default hostname,
there is no other user-visible change.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This provides a standard interface to setting the global networking config
for all interfaces and interface types.
For ports that already use either a static hostname (mimxrt, rp2) they will
now use the configured value. The default is configured by the port
(or optionally the board).
For interfaces that previously supported .config(hostname), this is still
supported but now implemented using the global network.hostname.
Similarly, pyb.country and rp2.country are now deprecated, but the methods
still exist (and forward to network.hostname).
Because ESP32/ESP8266 do not use extmod/modnetwork.c they are not affected
by this commit.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Makefile's support "else ifdef", so use it to make the logic clearer.
Also dedent some associated lines for consistency.
Signed-off-by: Damien George <damien@micropython.org>
This matches the behavior of the makefile ports but implemented for CMake,
making it easy to specify custom board definitions.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This matches the behavior of the makefile ports but implemented for CMake,
making it easy to specify custom board definitions.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This allows:
$ make BOARD_DIR=path/to/board
to infer BOARD=board, rather than the previous behavior that required
additionally setting BOARD explicitly.
Also makes the same change for VARIANT_DIR -> VARIANT on Unix.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Signed-off-by: Damien George <damien@micropython.org>
This RNG passes many of the Diehard tests and also the AIS31 test suite.
The RNG is quite slow, delivering 200bytes/s.
Tested on boards with and without a crystal.
It turned out that the result of calling ticks_us() was always either odd
or even, depending on some internal state during boot. So the us-counter
was set to a 2 MHz input and the result shifted by 1. The counting period
is still long enough, since internally a (now) 63 bit value is used for us.
By using the phase jitter between the DFLL48M clock and the FDPLL96M clock.
Even if both use the same reference source, they have a different jitter.
SysTick is driven by FDPLL96M, the us counter by DFLL48M. As a random
source, the us counter is read out on every SysTick and the value is used
to accumulate a simple multiply, add and xor register. According to tests
it creates about 30 bit random bit-flips per second. That mechanism will
pass quite a few RNG tests, has a suitable frequency distribution and
serves better than just the time after boot to seed the PRNG.
Allowing to increase the clock a little bit to 54Mhz. Not much of a gain,
but useful for generating a RNG entropy source from the jitter between
DFLL48M and FDPLL96M.
Remove two SPARKFUN_SAMD51_THINGS_PLUS pin definitions. There were
definitions of TXD and RXD, but these pins do not exist on the board. They
were only shown in the schematics.
Also remove any reference to LED_. This is just a text change, no
functional change.
For compatibility with other ports. Code increase up to ~1250 bytes for
SAMD21. The feature is configurable via MICROPY_PY_MACHINE_PIN_BOARD_CPU
in case flash memory is tight.
This further aligns the features available on Pico and Pico W boards.
os.dupterm is generally useful, but can still be disabled by a board if
needed. hashlib.sha1 requires mbedtls for the implementation, but that's
always available (due to ucryptolib's requirements). The entire hashlib
module can still be disabled by an individual board if needed.
Fixes issue #7881.
Signed-off-by: Damien George <damien@micropython.org>
Before, both uwTick and mp_hal_ticks_ms() were used as clock source. That
assumes, that these two are synchronous and start with the same value,
which may be not the case for all ports. If the lag between uwTick and
mp_hal_ticks_ms() is larger than the timer interval, the timer would either
rush up until the times are synchronous, or not start until uwTick wraps
over.
As suggested by @dpgeorge, MICROPY_SOFT_TIMER_TICKS_MS is now used in
softtimer.c, which has to be defined in a port's mpconfigport.h with
the variable that holds the SysTick counter.
Note that it's not possible to switch everything in softtimer.c to use
mp_hal_ticks_ms() because the logic in SysTick_Handler that schedules
soft_timer_handler() uses (eg on mimxrt) the uwTick variable directly
(named systick_ms there), and mp_hal_ticks_ms() uses a different source
timer. Thus it is made fully configurable.
The default now includes all sub-components (security, l2cap, etc)
and using the kwarg options is no longer supported.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The default now includes all sub-components (security, l2cap, etc)
and using the kwarg options is no longer supported.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Prior to this commit, on Pico W (where the CYW43 driver is enabled) the PIO
instruction memory was not released on soft reset, so using PIO after a
soft reset would eventually (after a few soft resets) lead to ENOMEM when
allocating a PIO program.
This commit fixes that by tracking the use of PIO memory by this module and
freeing it on soft reset.
Similarly, use of the state machines themselves are tracked and released on
soft reset.
Fixes issue #9003.
Signed-off-by: Damien George <damien@micropython.org>
Make this more generally useful and in line with what the mingw
and unix ports do: 16bit dig size to work on 32bit ports, a
self-contained qstrdefs.preprocessed.h because makemanifest.py
uses that, and a dev variant which effectively puts this to use:
previously the uasyncio module wasn't frozen but instead tests
ran by importing it from the extmod/ directory.
The mpversion.h file must exist before py/ source can be preprocessed,
but this went unnoticed because micropython.vcxproj always calls
MakeVersionHdr before MakeQstrDefs.
The variant.props may have incompatible build options which break
the mpy-cross build and in any case mpy-cross has nothing to do
with variant support.
This is in line with the change made for other ports in d53c3b6a: since
the default output directory already includes the variant name in it
there's no need to add it to the executable as well.
This will ensure that any board with networking support gets:
- webrepl
- mip
- urequests
- ntptime
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This drops the `.cpu` directive from the ARM gchelper_*.s files. Having
this directive breaks the linker when targeting older CPUs (e.g. `-mthumb
-mthumb-interwork` for `-mcpu=arm7tdmi`). The actual target CPU should be
determined by the compiler options.
The exact CPU doesn't actually matter, but rather the supported assembly
instruction set. So the files are renamed to *_thumb1.s and *thumb2.s to
indicate the instruction set support instead of the CPU support.
Signed-off-by: David Lechner <david@pybricks.com>
Prior to this commit, Pin(Pin.OPEN_DRAIN, value=0) would not set the
initial value of the open-drain pin to low, instead it would be high.
Signed-off-by: Damien George <damien@micropython.org>
The mp_plat_print output is already being used by the subsequent call to
mp_obj_print_exception(). And this eliminates all references to printf for
this port (at least in non-debug builds).
Signed-off-by: Damien George <damien@micropython.org>
The delay is 1 ms. It avoids the crashes reported by the
issues #8289, #8792 and #9236 with esp-idf versions >= 4.2, but does
not solve an underlying problem in the esp-idf.
The major setting is about the PHY interface configuration. The
configuration matches the Olimex ESP32 Gateway as well.
Tested with esp-idf v4.2.4 and Olimex ESP32 POE boards.
`esp_eth_ioctl(ETH_CMD_S_MAC_ADDR)` sets the MAC address of the hardware
device, but we also need to notify the upper layers of the change so that
e.g. DHCP work properly.
Add support for various SPI-based ethernet chips (W5500, KSZ8851SNL,
DM9051) to the ESP32 port. This leverages the existing support in ESP-IDF
for these chips -- which configures these chips in "MAC raw" mode -- and
the existing support for network.LAN in the ESP32 port. In particular,
this doesn't leverage the wiznet5k support that is used on the rp2 and
stm32 ports (because that's for native use of lwIP).
Tested on the POE Featherwing (with the SJIRQ solder jumper bridged) and a
ESP32-S3 feather.
A note about the interrupt pin: The W5500 implementation within ESP-IDF
relies on hardware interrupt, and requires the interrupt pin from the W5500
to be wired to a GPIO. This is not the case by default on the Adafruit
Ethernet FeatherWing, which makes it not directly compatible with this
implementation.
Both the direction and the Pin used for ref_clk can now be configured. It
Requires at least idf v4.4. The new keyword arguments to the constructor
are:
- ref_clk_mode=mode: with mode being Pin.IN or Pin.OUT. If it is not set,
then the default configuration is used, which may be configured by
kconfig settings.
- ref_clk=pin_obj: which defines the Pin used for ref_clk. This is either
Pin(0), Pin(16) or Pin(17). No check is done for the pin number. If it
is the wrong one, it simply will not work. Besides that, no harm.
LAN8710 uses the same drivers as LAN8720, so this commit just adds the
names. Alternatively, both could be summarised under LAN87xx, like the
esp-idf does.
Pin defines are:
- For Pico define board pins and the default LED pin (WL_GPIO25).
- For Pico-W define board pins, external pins and the default
LED pin (WL_GPIO0).
- For the Nano-RP2040, define board pins, external pins and
the default LED pin (GPIO25)
- For all other boards, the pins.csv defines the LED pin (if any)
for backwards compatibility with code that assumes there's always
an LED pin.
This commit adds support for generating named pin mappings for all pins
including CPU, board-defined, LED and externally controlled pins. CPU pins
are mapped to `pin_GPIO<n>`, externally-controlled pins are mapped to
`pin_EXT_GPIO<n>`, and defined conditionally (up to 10 pins, and can be
expanded in the future), and they are non-const to allow `machine-pin.c` to
write the pin object fields. Both CPU and externally controlled pins are
generated even if there's no board CSV file; if one exists it will just be
added to board pins.
Handle externally controlled GPIO pins more generically, by removing all
CYW43-specific code from `machine_pin.c`, and adding hooks to initialise,
configure, read and write external pins. This allows any driver for an
on-board module which controls GPIO pins (such as CYW43 or NINA), to
provide its own implementation of those hooks and work seamlessly with
`machine_pin.c`.
This commit uses the REGION_ALIAS GNU linker command to simplify the linker
snippets and consolidate the duplication.
Signed-off-by: Damien George <damien@micropython.org>
To allow the USB to work in cases where there is a lot of filesystem
access, in particular on boot.
For example, registering of the USB CDC interface may fail if:
- the board file system is lfs2 (default), and
- sys.path contains entries for the local file system (default), and
- files are imported by boot.py or main.py from frozen bytecode of the file
system (common) and the file system contains many files, like 100.
In that case the board is very busy with scanning LFS, and registering the
USB interface seems to time out. This commit fixes this by allowing the
USB to make progress during filesystem reads.
Also switch existing MICROPY_EVENT_POLL_HOOK uses in this file to
MICROPY_EVENT_POLL_HOOK_FAST now that the latter macro exists.
When switching from a special function like SPI to an input or output,
there was a brief period after the function was disabled but before the
pin's I/O state was configured, in which the state would be poorly defined.
This fixes the problem by switching off the special function after fully
configuring the I/O state.
Fixes#10226.
Signed-off-by: Paul Grayson <pdg@alum.mit.edu>
There were several places where 32-bit integer could overflow with
frequencies of 2^28 Hz or above (~268 MHz). This fixes those overflows and
also introduces rounding for more accurate duty_ns computations.
Signed-off-by: Paul Grayson <pdg@alum.mit.edu>
This changes the freq() and duty_u16() functions to use more simpler, more
accurate formulas, in particular increasing the frequency accuracy from a
few percent to a fraction of a percent in many cases.
Signed-off-by: Paul Grayson <pdg@alum.mit.edu>
This commit prevents the device from "hanging" when using lightsleep while
the WiFi chip is active.
Whenever the WiFi chip wants to interrupt the microcontroller to notify it
for a new package, it sets the CYW43_PIN_WL_HOST_WAKE pin to high,
triggering an IRQ. However, as polling the chip cannot happen in an
interrupt handler, it subsequently notifies the pendsv-service to do a poll
as soon as the interrupt handler ended. In order to prevent a new
interrupt from happening immediately afterwards, even before the poll has
run, the IRQ handler disables interrupts from the pin.
The first problem occurs, when a WiFi package arrives while the main loop
is in cyw43-code. In order to prevent concurrent access of the hardware,
the network code blocks pendsv from running again while entering lwIP code.
The same holds for direct cyw43 code (like changing the cyw43-gpios, i.e.
the LED on the Pico W). While the pendsv is disabled, interrupts can still
occur to schedule a poll (and disable further interrupts), but it will not
run. This can happen while the microcontroller is anywhere in rp2040 code.
In order to preserve power while waiting for cyw43 responses,
cyw43_configport.h defines CYW43_DO_IOCTL_WAIT and
CYW43_SDPCM_SEND_COMMON_WAIT to __WFI(). While this might work in most
cases, there are 2 edge cases where it fails:
- When an interrupt has already been received by the cyw43 stack, for
example due to an incoming ethernet packet.
- When the interrupt from the cyw43 response comes before the
microcontroller entered the __WFI() instruction.
When that happens, wfi will just block forever as no further interrupts are
received. The only way to safely use wfi to wake up from an interrupt is
inside a critical section, as this delays interrupts until the wfi is
entered, possibly resuming immediately until interrupts are reenabled and
the interrupt handler is run. Additionally this critical section needs to
check whether the interrupt has already been disabled and pendsv was
triggered, as in such a case, wfi can never be woken up, and needs to be
skipped, because there is already a package from the network chip waiting.
Note that this turns cyw43_yield into a nop (and thereby the cyw43-loops
into busy waits) from the second time onwards, as after the first call, a
pendsv request will definitely be pending. More logic could be added, to
explicitly enable the interrupt in this case.
Regarding lightsleep, this code has a similar problem. When an interrupt
occurs during lightsleep, the IRQ and pendsv handler and thereby poll are
run immediately, with the clocks still disabled, causing the SPI transfers
to fail. If we don't want to add complex logic inside the IRQ handler we
need to protect the whole lightsleep procedure form interrupts with a
critical section, exiting out early if an interrupt is pending for whatever
reason. Only then we can start to shut down clocks and only enable
interrupts when the system is ready again. Other interrupt handlers might
also be happy, that they are only run when the system is fully operational.
Tested on a Pico W, calling machine.lightsleep() within an endless loop and
pinging from the outside.
This required to add two functions down the stack to uart.c and ra.sci.c.
- One for telling, whther the transmission is busy.
- One for reporting the size of the TX buffer.
Tested with a EK-RA6M2 board.
See the previous commit, except in this case the customisation didn't
actually do anything so can just be removed.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This was previously implemented by adding additional members to the
mp_obj_type_t defined for each NIC, which is difficult to do cleanly with
the new object type slots mechanism. The way this works is also not
supported on GCC 8.x and below.
Instead replace it with the type protocol, which is a much simpler way of
achieving the same thing.
This affects the WizNet (in non-LWIP mode) and Nina NIC drivers.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Changes in this commit:
- Clear and mask D2 EXTIs.
- Set correct voltage scaling level for standby mode.
- Disable debug MCU (if debugging is disabled), for all MCU series.
It keeps compatibility with the XIAO bootloader by:
- using Soft Device 7.3.0
- reserving 48k memory for the bootloader.
So on double reset a drive pops for uploading an uf2 image or a nrfutil zip
pkg file. Instructions to create it from a hex file are included. The
bootloader can as well be activated with the touch 1200 option of nrfutil.
The script download_ble_stack.sh has been adapted to get the version 7.3.0
soft device files. It may have to be executed once before building.
The file system is set to 256k and the pin definitions are adapted.
Besides that, it has the common functionality and omissions. The on-board
sensors and additional flash can be supported by Python scripts.
This was introduced by 35fb90bd57, but
it is much simpler and essentially the same to just use
`tud_cdc_n_connected()`.
The only difference is that tud_cdc_n_connected() only checks for DTR,
but this is correct anyway: DTR indicates device presence, RTS indicates
that the host wants to receive data.
Signed-off-by: Damien Tournoud <damien@platform.sh>
usocket_events_deinit will only be available if MICROPY_PY_USOCKET_EVENTS
is enabled (which is only enabled when webrepl is enabled).
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
ADC: The argument of vref=num is an integer. Values for num are:
SAMD21:
0 INT1V 1.0V voltage reference
1 INTVCC0 1/1.48 Analog voltage supply
2 INTVCC1 1/2 Analog voltage supply (only for VDDANA > 2.0V)
3 VREFA External reference
4 VREFB External reference
SAMD51:
0 INTREF internal bandgap reference
1 INTVCC1 Analog voltage supply
2 INTVCC0 1/2 Analog voltage supply (only for VDDANA > 2.0v)
3 AREFA External reference A
4 AREFB External reference B
5 AREFC External reference C (ADC1 only)
DAC: The argument of vref=num is an integer. Suitable values:
SAMD21:
0 INT1V Internal voltage reference
1 VDDANA Analog voltage supply
2 VREFA External reference
SAMD51:
0 INTREF Internal bandgap reference
1 VDDANA Analog voltage supply
2 VREFAU Unbuffered external voltage reference (not buffered in DAC)
4 VREFAB Buffered external voltage reference (buffered in DAC).
Changes in this commit:
- Do not deinit IRQ when uart.deinit() is called with an inactive object.
- Remove using it for the finaliser. There is another machanism for soft
reset, and it is not needed otherwise.
- Do not tag the UART buffers with MP_STATE_PORT, it is not required.
