Commit Graph

13 Commits

Author SHA1 Message Date
robert-hh
e33db80a59 samd/clock_config: Extend the SAMD51 us-counter to 60 bit.
This removes the difference in the time.ticks_us() range between SAMD21 and
SAMD51.

The function mp_hal_ticks_us_64() is added and used for:
- SAMD51's mp_hal_ticks_us and mp_hal_delay_us().
  For SAMD21, keep the previous methods, which are faster.
- mp_hal_ticks_ms() and mp_hal_tick_ms_64(), which saves some bytes
  and removes a potential race condition every 50 days.

Also set the us-counter for SAMD51 to 16 MHz for a faster reading of the
microsecond value.

Note: With SAMD51, mp_hal_ticks_us_64() has a 60 bit range only, which is
still a long time (~36000 years).
2022-10-25 23:26:14 +11:00
robert-hh
fc9d66fac6 samd/machine_rtc: Add the machine.RTC class.
Methods implemented are:
- rtc.init(date)
- rtc.datetime([new_date])
- rtc.calibration(value)

The presence of this class can be controlled by MICROPY_PY_MACHINE_RTC.  If
the RTC module is used, the time module uses the RTC as well.

For boards without a 32kHz crystal, using RTC makes no sense, since it will
then use the ULP32K oscillator, which is not precise at all.  Therefore, it
will by default only be enabled for boards using a crystal, but can be
enabled in the respective mpconfigboard.h.
2022-10-25 23:20:09 +11:00
robert-hh
be31fde012 samd/mcu: Make some settings in mpconfigmcu.h conditional.
And set the default for MICROPY_PY_MATH as 1 for both MCU types.
2022-10-25 23:13:58 +11:00
robert-hh
4c9e4c3310 samd/mcu/samd51: Enable FAT support for SAMD51.
Tested with a SD card connected to a SAMD51 board.  The SEEED WIO terminal
has a SD-Card reader built-in.

Also a side change to remove a few obsolete lines from Makefile.
2022-10-25 23:07:23 +11:00
robert-hh
fe31fca462 samd/mcu/samd51: Enable onewire support for SAMD51. 2022-10-25 23:07:01 +11:00
robert-hh
a7113e95d7 samd/modmachine: Add machine.dht_readinto and enable on SAMD51. 2022-10-25 23:06:44 +11:00
robert-hh
1c32cec7f1 samd/clock_config: Support changing machine.freq() for SAMD21.
The range is 1MHz - 48 MHz.  Note that below 8 MHz there is no USB support.
The frequency will be set to an integer fraction of 48 MHz.  And after
changing the frequency, the peripherals like PWM, UART, I2C, SPI have to be
reconfigured.

Current consumption e.g. of the Seeed Xiao board at 1 MHz is about 1.5 mA,
mostly caused by the on-board LED (green LED with 1k resistor at 3.3V).
2022-10-25 22:40:16 +11:00
robert-hh
9f4df86016 samd/boards: Move the flash filesystem definitions to the linker files.
They used to be in mpconfigmcu.h, but have to be different for different
chip variants, like the SAMD51x20.
2022-10-06 23:14:08 +11:00
robert-hh
387025f5d1 samd/mcu: Enable the math module on SAMD51. 2022-10-06 23:11:02 +11:00
robert-hh
d9338aabc5 samd: Change the symbol names for the peripheral clocks.
From APB_FREQ to DFLL48M_FREQ, and from apb_freq to peripheral_freq.
2022-10-06 23:10:08 +11:00
robert-hh
929dfc66a3 samd/mpconfigport: Restructure to use ROM feature levels.
Changes are:
- Set the feature level for each MCU: CORE features for SAMD21, and EXTRA
  features for SAMD51.
- Remove all definitions that are included in the core feature level.
- Keep the default settings for feature level and float, to make the choice
  obvious.
2022-10-06 23:00:44 +11:00
robert-hh
9a567b04e7 samd/machine_uart: Support buffered TX for UART.
It can be enabled/disabled by a configuration switch.  The code size
increase is 308 bytes, but it requires RAM space for buffers, the larger
UART object and root pointers.
2022-10-06 22:57:37 +11:00
robert-hh
aa6dbbcffd samd/mcu: Factor out MCU policy for SAMD21 and SAMD51.
Which contains a mpconfigmcu.h, mpconfigmcu.mk and manifest.py file for
each MCU group.  That looks better than the previous choice.
2022-10-06 22:56:13 +11:00