Commit Graph

121 Commits

Author SHA1 Message Date
Damien George
19778d0a3c stm32/i2c: Add low-level I2C driver for F7 MCUs. 2018-04-24 23:48:04 +10:00
Damien George
b73adcc3d9 stm32: Rename i2c.c to pyb_i2c.c.
i2c.c implements the legacy pyb.I2C class so rename the file to make this
explicit, and also to make room for an improved I2C driver.
2018-04-24 16:23:36 +10:00
Damien George
d9e69681f5 stm32: Add custom, optimised Reset_Handler code.
The Reset_Handler needs to copy the data section and zero the BSS, and
these operations should be as optimised as possible to reduce start up
time.  The versions provided in this patch are about 2x faster (on a Cortex
M4) than the previous implementations.
2018-03-29 15:29:23 +11:00
Damien George
04de9e33bc stm32/system_stm32: Set VTOR pointer from TEXT0_ADDR. 2018-03-27 21:32:39 +11:00
Damien George
ed75b2655f stm32/Makefile: Allow a board to config either 1 or 2 firmware sections.
This patch forces a board to explicitly define TEXT1_ADDR in order to
split the firmware into two separate pieces.  Otherwise the default is now
to produce only a single continuous firmware image with all ISR, text and
data together.
2018-03-27 21:24:15 +11:00
Damien George
95b2cb008e stm32/Makefile: Rename FLASH_ADDR/TEXT_ADDR to TEXT0_ADDR/TEXT1_ADDR.
To make it clearer that these addresses are both for firmware text and that
they have a prescribed ordering.
2018-03-27 21:20:04 +11:00
Damien George
7aec06ca9a stm32/boards: Allow boards to have finer control over the linker script.
This patch allows a particular board to independently specify the linker
scripts for 1) the MCU memory layout; 2) how the different firmware
sections are arranged in memory.  Right now all boards follow the same
layout with two separate firmware section, one for the ISR and one for the
text and data.  This leaves room for storage (filesystem data) to live
between the firmware sections.

The idea with this patch is to accommodate boards that don't have internal
flash storage and only need to have one continuous firmware section.  Thus
the common.ld script is renamed to common_ifs.ld to make explicit that it
is used for cases where the board has internal flash storage.
2018-03-27 21:17:48 +11:00
Damien George
b63cc1e9ef stm32/Makefile: Re-enable strict aliasing optimisation for ST HAL files.
The HAL requires strict aliasing optimisation to be turned on to function
correctly (at least for the SD card driver on F4 MCUs).  This optimisation
was recently disabled with the addition of H7 support due to the H7 HAL
having errors with the strict aliasing optimisation enabled.  But this is
now fixed in the latest stm32lib and so the optimisation can now be
re-enabled.

Thanks to @chuckbook for finding that there was a problem with the SD card
on F4 MCUs with the strict aliasing optimisation disabled.
2018-03-26 00:00:47 +11:00
Damien George
e37b8ba5a5 stm32: Use STM32xx macros instead of MCU_SERIES_xx to select MCU type.
The CMSIS files for the STM32 range provide macros to distinguish between
the different MCU series: STM32F4, STM32F7, STM32H7, STM32L4, etc.  Prefer
to use these instead of custom ones.
2018-03-17 10:42:50 +11:00
Damien George
58ebeca6a9 drivers/bus: Pull out software SPI implementation to dedicated driver.
This patch takes the software SPI implementation from extmod/machine_spi.c
and moves it to a dedicated file in drivers/bus/softspi.c.  This allows the
SPI driver to be used independently of the uPy runtime, making it a more
general component.
2018-03-10 00:59:43 +11:00
iabdalkader
66748aaf60 stm32/Makefile: Use separate startup file for each MCU series. 2018-03-09 15:14:17 +11:00
iabdalkader
b8d09b9bef stm32/Makefile: Add settings to support H7 MCUs. 2018-03-09 15:09:29 +11:00
Damien George
adda38cf76 stm32/qspi: Add hardware QSPI driver, with memory-map capability.
It supports the abstract QSPI protocol defined in drivers/bus/qspi.h.
2018-03-03 00:17:08 +11:00
Damien George
0210383da5 stm32/spibdev: Add option to configure SPI block dev to use QSPI flash.
To use QSPI (in software QSPI mode) the configuration needed is:

    #define MICROPY_HW_SPIFLASH_SIZE_BITS (n * 1024 * 1024)
    #define MICROPY_HW_SPIFLASH_CS      (pin_x1)
    #define MICROPY_HW_SPIFLASH_SCK     (pin_x2)
    #define MICROPY_HW_SPIFLASH_IO0     (pin_x3)
    #define MICROPY_HW_SPIFLASH_IO1     (pin_x4)
    #define MICROPY_HW_SPIFLASH_IO2     (pin_x5)
    #define MICROPY_HW_SPIFLASH_IO3     (pin_x6)
2018-03-02 23:55:45 +11:00
Damien George
e6220618ce stm32: Use "GEN" for describing files generated in the build.
Instead of "Create", to match the build output from the py/ core.
2018-02-23 16:27:30 +11:00
Damien George
fa13e0d35b stm32: Factor out flash and SPI block-device code to separate files.
Prior to this patch, storage.c was a combination of code that handled
either internal flash or external SPI flash and exposed one of them as a
block device for the local storage.  It was also exposed to the USB MSC.

This patch splits out the flash and SPI code to separate files, which each
provide a general block-device interface (at the C level).  Then storage.c
just picks one of them to use as the local storage medium.  The aim of this
factoring is to allow to add new block devices in the future and allow for
easier configurability.
2018-02-13 22:21:46 +11:00
Damien George
57d2ac1300 stm32/rng: Simplify RNG implementation by accessing raw peripheral regs.
It saves code size and RAM, and is more efficient to execute.
2018-02-02 18:22:57 +11:00
Damien George
efdda2c62d stm32: Add support for DHT11/DHT22 sensors. 2018-01-31 18:12:53 +11:00
Damien George
e36821a766 stm32/modnwwiznet5k: Add support for W5500 Ethernet chip.
Which Wiznet chip to use is a compile-time option: MICROPY_PY_WIZNET5K
should be set to either 5200 or 5500 to support either one of these
Ethernet chips.  The driver is called network.WIZNET5K in both cases.

Note that this commit introduces a breaking-change at the build level
because previously the valid values for MICROPY_PY_WIZNET5K were 0 and 1
but now they are 0, 5200 and 5500.
2017-10-16 15:36:57 +11:00
Damien George
4a93801c12 all: Update Makefiles and others to build with new ports/ dir layout.
Also renames "stmhal" to "stm32" in documentation and everywhere else.
2017-09-06 14:09:13 +10:00
Damien George
01dd7804b8 ports: Make new ports/ sub-directory and move all ports there.
This is to keep the top-level directory clean, to make it clear what is
core and what is a port, and to allow the repository to grow with new ports
in a sustainable way.
2017-09-06 13:40:51 +10:00