The FIFO reports not only the bytes read, but also 4 error bits. These were
not checked, leading to NUL value read in case of break and possible
garbage bytes being written on parity/framing error.
This patch addresses the issue that NUL bytes are incorrectly read on
break, and at least provides the boilerplate code and comments for error
handling, that may be implemented in the future.
Signed-off-by: Maarten van der Schrieck <maarten@thingsconnected.nl>
This is a code factoring to have the Python bindings in one location, and
all the ports use those same bindings. For all ports except the two listed
below there is no functional change.
The nrf port has UART.sendbreak() removed, but this method previously did
nothing.
The zephyr port has the following methods added:
- UART.init(): supports setting timeout and timeout_char.
- UART.deinit(): does nothing, just returns None.
- UART.flush(): raises OSError(EINVAL) because it's not implemented.
- UART.any() and UART.txdone(): raise NotImplementedError.
Signed-off-by: Damien George <damien@micropython.org>
Prior to this change, setting of UART parameters like parity, stop bits or
data bits did not work correctly. As suggested by @iabdalkader, adding
__DSB() fixes the problem, making sure that changes to the UART LCR_H
register are seen by the peripheral.
Note: the FIFO is already enabled in the call to uart_init(), so the call
to uart_set_fifo_enabled() is not required, but kept for visibility.
Fixes issue #10976.
Instead of being an explicit field, it's now a slot like all the other
methods.
This is a marginal code size improvement because most types have a make_new
(100/138 on PYBV11), however it improves consistency in how types are
declared, removing the special case for make_new.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The goal here is to remove a slot (making way to turn make_new into a slot)
as well as reduce code size by the ~40 references to mp_identity_getiter
and mp_stream_unbuffered_iter.
This introduces two new type flags:
- MP_TYPE_FLAG_ITER_IS_ITERNEXT: This means that the "iter" slot in the
type is "iternext", and should use the identity getiter.
- MP_TYPE_FLAG_ITER_IS_CUSTOM: This means that the "iter" slot is a pointer
to a mp_getiter_iternext_custom_t instance, which then defines both
getiter and iternext.
And a third flag that is the OR of both, MP_TYPE_FLAG_ITER_IS_STREAM: This
means that the type should use the identity getiter, and
mp_stream_unbuffered_iter as iternext.
Finally, MP_TYPE_FLAG_ITER_IS_GETITER is defined as a no-op flag to give
the default case where "iter" is "getiter".
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
uart.flush()
flush() will wait until all characters have been sent. It may return
while the last character is sent. if needed, the calling code has to
add one character wait time. To avoid a permanent lock, a timeout
applies depending on the size of txbuf and the baud rate.
ret = uart.txdone()
ret is True if no transfer is in progress. It may return True if the
last byte of a transfer is sent.
ret is False otherwise.
Duplication of characters is caused by re-entrant calls from separate cores
of uart_fill_tx_fifo(). This patch uses a mutex to ensure that a
re-entrant execution of the function returns without affecting the UART
FIFO.
Fixes issues #8344 and #8360.
The UART hardware flow control was not working correctly, the receive FIFO
was always fetched and RTS was never deasserted. This is not a problem
when hardware flow control is not used: normally, if the receive FIFO is
full, the UART receiver won't receive data into the FIFO anymore, but the
current implementation fetches from the FIFO and discards it instead.
The problem is that data is discarded even when RTS is enabled.
This commit fixes the issue by only taking from the FIFO if there is room
in the ring buffer to put the character.
Signed-off-by: YoungJoon Chun <yjchun@mac.com>
Without these methods a lot of existing "portable" scripts are broken.
This change improves portability by making rp2 machine.UART more compliant
with the documented machine UART interface.
The pico-sdk 1.3.0 update in 97a7cc243b
introduced a change that broke RP2 Bluetooth UART, and possibly UART in
general, which stops working right after UART is initialized. The commit
raspberrypi/pico-sdk@2622e9b enables the UART receive timeout (RTIM) IRQ,
which is asserted when the receive FIFO is not empty, and no more
characters are received for a period of time.
This commit makes sure the RTIM IRQ is handled and cleared in
uart_service_interrupt.
Prior to this fix, if the UART hardware FIFO had a few chars but still
below the FIFO trigger threshold, and the ringbuf was empty, the read
function would timeout if timeout==0 (the default timeout).
This fix follows the suggestion of @iabdalkader.
The RX IRQ does not trigger if the FIFO is less than the trigger level, in
which case characters may be available in the FIFO, yet not in the ringbuf,
and the ioctl returns false.
Instantiation and init now support the rxbuf and txbuf keywords for setting
the buffer size. The default size is 256 bytes. The minimum and maximum
sizes are 32 and 32766 respectively.
uart.write() still includes checks for timeout, even if it is very unlikely
to happen due to a) lack of flow control support and b) the minimal timeout
values being longer than the time it needs to send a byte.
This commit adds a new port "rp2" which targets the new Raspberry Pi RP2040
microcontroller.
The build system uses pure cmake (with a small Makefile wrapper for
convenience). The USB driver is TinyUSB, and there is a machine module
with most of the standard classes implemented. Some examples are provided
in the examples/rp2/ directory.
Work done in collaboration with Graham Sanderson.
Signed-off-by: Damien George <damien@micropython.org>
