Commit Graph

39 Commits

Author SHA1 Message Date
Damien George
829aa58c5c stm32/usbd_msc: Provide custom irquiry processing by MSC interface.
So the MSC interface can customise the inquiry response based on the
attached logical units.
2019-06-11 15:43:58 +10:00
Damien George
3fc7c8e35c stm32/usb: Include py/mpconfig.h instead of mpconfigboard.h.
Because py/mpconfig.h has header include guards.
2019-05-31 21:39:34 +10:00
Damien George
ff91b05cfa stm32/usb: Support up to 3 VCP interfaces on USB device peripheral.
To enable define MICROPY_HW_USB_CDC_NUM to 3.
2019-05-31 11:35:42 +10:00
Damien George
0c29502ad9 stm32/usb: Refactor CDC VCP code to enable N CDC interfaces.
The board config option MICROPY_HW_USB_ENABLE_CDC2 is now changed to
MICROPY_HW_USB_CDC_NUM, and the latter should be defined to the maximum
number of CDC interfaces to support (defaults to 1).
2019-05-30 21:11:04 +10:00
Andrew Leech
70a28e3ad9 stm32/usb: Add USB device mode for VCP+VCP without MSC.
Selectable via pyb.usb_mode('VCP+VCP').
2019-04-28 21:31:47 +10:00
Damien George
f66c4cbfa6 stm32/usbdev: Make USB device descriptors at runtime rather than static. 2019-04-26 10:07:49 +10:00
Andrew Leech
67689bfd7e stm32/usb: Add flow control option for USB VCP data received from host.
It's off by default and can be enabled at run-time with:

    pyb.USB_VCP().init(flow=pyb.USB_VCP.RTS)
2019-01-31 23:31:26 +11:00
Damien George
4caf5b2358 stm32/usbdev: Add USB config option for max power drawn by the board.
The new compile-time option is MICROPY_HW_USB_MAX_POWER_MA.  Set this in
the board configuration file to the maximum current in mA that the board
will draw over USB.  The default is 500mA.
2019-01-27 14:02:10 +11:00
Damien George
7d8db42d17 stm32/usbdev: Add USB config option for board being self powered.
The new compile-time option is MICROPY_HW_USB_SELF_POWERED.  Set this
option to 1 in the board configuration file to indicate that the USB device
is self powered.  This option is disabled by default (previous behaviour).
2019-01-27 13:52:43 +11:00
Damien George
0f6f86ca49 stm32/usbd_cdc_interface: Refactor USB CDC tx code to not use SOF IRQ.
Prior to this commit the USB CDC used the USB start-of-frame (SOF) IRQ to
regularly check if buffered data needed to be sent out to the USB host.
This wasted resources (CPU, power) if no data needed to be sent.

This commit changes how the USB CDC transmits buffered data:
- When new data is first available to send the data is queued immediately
  on the USB IN endpoint, ready to be sent as soon as possible.
- Subsequent additions to the buffer (via usbd_cdc_try_tx()) will wait.
- When the low-level USB driver has finished sending out the data queued
  in the USB IN endpoint it calls usbd_cdc_tx_ready() which immediately
  queues any outstanding data, waiting for the next IN frame.

The benefits on this new approach are:
- SOF IRQ does not need to run continuously so device has a better chance
  to sleep for longer, and be more responsive to other IRQs.
- Because SOF IRQ is off, current consumption is reduced by a small amount,
  roughly 200uA when USB is connected (measured on PYBv1.0).
- CDC tx throughput (USB IN) on PYBv1.0 is about 2.3 faster (USB OUT is
  unchanged).
- When USB is connected, Python code that is executing is slightly faster
  because SOF IRQ no longer interrupts continuously.
- On F733 with USB HS, CDC tx throughput is about the same as prior to this
  commit.
- On F733 with USB HS, Python code is about 5% faster because of no SOF.

As part of this refactor, the serial port should no longer echo initial
characters when the serial port is first opened (this only used to happen
rarely on USB FS, but on USB HS is was more evident).
2018-10-15 15:37:01 +11:00
Damien George
53ccbe6cec stm32/usbd_cdc_interface: Handle disconnect IRQ to set VCP disconnected.
pyb.USB_VCP().isconnected() will now return False if the USB is
disconnected after having previously been connected.

See issue #4210.
2018-10-15 12:24:40 +11:00
Damien George
aa4a7a8732 stm32/usb: Guard USB device code with #if for whether USB is enabled.
With this change, all the USB source code can now be passed through the
compiler even if the MCU does not have a USB peripheral.
2018-05-28 21:45:46 +10:00
Damien George
e6b66f1092 stm32/usb: Initialise cdc variable to prevent compiler warnings.
Some compilers cannot deduce that cdc will always be written before being
used.
2018-05-15 00:18:03 +10:00
Damien George
47ecbbbecb stm32/usb: Add ability to have 2x VCP interfaces on the one USB device.
This patch adds the configuration MICROPY_HW_USB_ENABLE_CDC2 which enables
a new USB device configuration at runtime: VCP+VCP+MSC.  It will give two
independent VCP interfaces available via pyb.USB_VCP(0) and pyb.USB_VCP(1).
The first one is the usual one and has the REPL on it.  The second one is
available for general use.

This configuration is disabled by default because if the mode is not used
then it takes up about 2200 bytes of RAM.  Also, F4 MCUs can't support this
mode on their USB FS peripheral (eg PYBv1.x) because they don't have enough
endpoints.  The USB HS peripheral of an F4 supports it, as well as both the
USB FS and USB HS peripherals of F7 MCUs.
2018-05-14 23:44:45 +10:00
Damien George
2e565cc0d4 stm32/usb: Change HID report funcs to take HID state, not usbdev state. 2018-05-14 17:04:43 +10:00
Damien George
91bca340ec stm32/usb: Change CDC tx/rx funcs to take CDC state, not usbdev state. 2018-05-14 16:55:04 +10:00
Damien George
68271a27e6 stm32/usb: Make CDC endpoint definitions private to core usbdev driver. 2018-05-14 16:53:45 +10:00
Damien George
ed92d62326 stm32/usb: Combine HID lower-layer and interface state into one struct. 2018-05-14 16:34:31 +10:00
Damien George
bf08a99ccd stm32/usb: Combine CDC lower-layer and interface state into one struct. 2018-05-14 16:15:58 +10:00
Peter D. Gray
1f1623d3b7 stm32/usbdev: Be honest about data not being written to HID endpoint.
USB_HID.send() should now return 0 if it could not send the report to the
host.
2018-05-14 12:01:27 +10:00
Damien George
aeaace0737 stm32/usbdev: Remove unused RxState variable, and unused struct. 2018-05-11 23:20:59 +10:00
Damien George
abde0fa226 stm32/usbdev: Convert files to unix line endings.
Also remove trailing whitespace and convert tabs to spaces.
2018-05-11 23:03:52 +10:00
Damien George
d966a33486 stm32: Change header include guards from STMHAL to STM32 to match dir. 2018-02-15 15:47:04 +11:00
Damien George
5c320bd0b0 stm32: Introduce MICROPY_HW_ENABLE_USB and clean up USB config.
This patch allows to completely compile-out support for USB, and no-USB is
now the default.  If a board wants to enable USB it should define:

    #define MICROPY_HW_ENABLE_USB (1)

And then one or more of the following to select the USB PHY:

    #define MICROPY_HW_USB_FS (1)
    #define MICROPY_HW_USB_HS (1)
    #define MICROPY_HW_USB_HS_IN_FS (1)
2018-02-13 18:51:08 +11:00
Damien George
8e1cb58a23 stm32/usbdev: Fix USBD setup request handler to use correct recipient.
Prior to this patch the USBD driver did not handle the recipient correctly
for setup requests.  It was not interpreting the req->wIndex field in the
right way: in some cases this field indicates the endpoint number but the
code was assuming it always indicated the interface number.

This patch fixes this.  The only noticeable change is to the MSC
interface, which should now correctly respond to the USB_REQ_CLEAR_FEATURE
request and hence unmount properly from the host when requested.
2018-02-12 17:22:59 +11:00
Damien George
db702ba722 stm32/usbdev: Add support for high-speed USB device mode.
This patch adds support in the USBD configuration and CDC-MSC-HID class for
high-speed USB mode.  To enable it the board configuration must define
USE_USB_HS, and either not define USE_USB_HS_IN_FS, or be an STM32F723 or
STM32F733 MCU which have a built-in HS PHY.  High-speed mode is then
selected dynamically by passing "high_speed=True" to the pyb.usb_mode()
function, otherwise it defaults to full-speed mode.

This patch has been tested on an STM32F733.
2018-02-01 17:57:44 +11:00
Damien George
3130424b54 stm32/usbdev: Add support for MSC-only USB device class.
Select this mode in boot.py via: pyb.usb_mode('MSC')
2018-02-01 15:47:16 +11:00
Damien George
1d4246a2e8 stm32/usbdev: Reduce dependency on py header files. 2018-02-01 12:44:16 +11:00
Damien George
3f6d3ccc11 stm32/usbdev: Pass thru correct val for SCSI PreventAllowMediumRemoval.
This value is "1" when the medium should not be removed, "0" otherwise.
2017-12-13 18:33:39 +11:00
Damien George
f7f4bf0321 stm32/usbdev: Move all the USB device descriptor state into its struct. 2017-09-22 10:57:21 +10:00
Damien George
0ea73d2da7 stm32/usbdev: Simplify pointers to MSC state and block dev operations. 2017-09-21 21:51:12 +10:00
Damien George
f8f17f48c5 stm32/usbdev: Put all state for the USB device driver in a struct. 2017-09-21 21:51:04 +10:00
Damien George
b3b922f177 stm32/usbdev: Simplify HID tx/rx buffer passing. 2017-09-21 21:50:56 +10:00
Damien George
e04b478050 stm32/usbdev: Simplify CDC tx/rx buffer passing. 2017-09-21 21:50:48 +10:00
Damien George
77e1da40e2 stm32/usbdev: Put all HID state in a struct. 2017-09-21 21:50:37 +10:00
Damien George
980b33177b stm32/usbdev: Put all CDC state in a struct. 2017-09-21 21:48:28 +10:00
Damien George
78602a217f stm32/usbdev: Make the USBD callback struct const so it can go in ROM. 2017-09-20 17:44:16 +10:00
Damien George
f1dd0fd7df stm32: Remove unused usbd_msc.c file. 2017-09-06 14:50:08 +10:00
Damien George
01dd7804b8 ports: Make new ports/ sub-directory and move all ports there.
This is to keep the top-level directory clean, to make it clear what is
core and what is a port, and to allow the repository to grow with new ports
in a sustainable way.
2017-09-06 13:40:51 +10:00