Commit Graph

25 Commits

Author SHA1 Message Date
Damien George
e43a74a4db drivers/memory/spiflash: Add MICROPY_HW_SPIFLASH_ENABLE_CACHE option.
This only needs to be enabled if a board uses FAT FS on external SPI flash.
When disabled (and using external SPI flash) 4k of RAM can be saved.

Signed-off-by: Damien George <damien@micropython.org>
2020-12-18 13:39:32 +11:00
Damien George
df3b466d6c stm32/boards: Factor out common data/bss/heap/stack linker sections.
Signed-off-by: Damien George <damien@micropython.org>
2020-10-29 23:31:59 +11:00
Damien George
2b9900380a stm32/boards/STM32F769DISC: Use macro instead of const for flash size.
So that the flash size can be changed in just one place.  Also remove the
duplicate cache entry.
2020-06-12 10:28:26 +10:00
Damien George
d6a1e45caa stm32/usbd_conf: Allow boards to configure USB HS ULPI NXT/DIR pins. 2020-02-04 23:15:55 +11:00
Damien George
96a4435be1 stm32/boards/STM32F769DISC: Add config to use external SPI as filesys.
This board now has the following 3 build configurations:
- mboot + external QSPI in XIP mode + internal filesystem
- mboot + external QSPI with filesystem (the default)
- no mboot + external QSPI with filesystem
2020-01-30 14:40:38 +11:00
Jim Mussared
c8c37ca407 stm32/boards/STM32F769DISC: Fix number of SDRAM row bits.
According to the schematic, the SDRAM part on this board is a
MT48LC4M32B2B5-6A, with "Row addressing 4K A[11:0]" (per datasheet).  This
commit updates mpconfigboard.h from 13 to 12 to match.
2019-09-10 23:13:52 +10:00
Damien George
02b2ad4fbd stm32/boards/STM32F769DISC: Fix length of FLASH_APP section.
Fixes issue #4924.
2019-07-17 16:19:50 +10:00
Damien George
009b1f6559 stm32/boards: Rework all stm32??xx_hal_conf.h files to use common code.
This eliminates a lot of duplicated code in these header files.
2019-06-25 14:18:24 +10:00
Damien George
04c7cdb668 stm32: Enter bootloader via a system reset.
Entering a bootloader (ST system bootloader, or custom mboot) from software
by directly branching to it is not reliable, and the reliability of it
working can depend on the peripherals that were enabled by the application
code.  It's also not possible to branch to a bootloader if the WDT is
enabled (unless the bootloader has specific provisions to feed the WDT).

This patch changes the way a bootloader is entered from software by first
doing a complete system reset, then branching to the desired bootloader
early on in the start-up process.  The top two words of RAM (of the stack)
are reserved to store flags indicating that the bootloader should be
entered after a reset.
2019-06-25 14:15:49 +10:00
Damien George
5da60ff9cb stm32/boards: Enable ussl module via mbedtls for boards with network. 2019-06-24 17:48:28 +10:00
Chris Mason
14cf91f704 stm32: In link script, define start of stack separately from heap end.
Previously the end of the heap was the start (lowest address) of the stack.
With the changes in this commit these addresses are now independent,
allowing a board to place the heap and stack in separate locations.
2019-06-14 15:29:24 +10:00
Damien George
9670b26526 stm32: Rename MICROPY_HW_HAS_SDCARD to MICROPY_HW_ENABLE_SDCARD.
For consistency with the majority of other MICROPY_HW_ENABLE_xxx macros.
2019-04-01 15:21:26 +11:00
Damien George
e61862d063 stm32/boards: Update to use new build config for lwip component. 2019-03-04 23:34:03 +11:00
Damien George
84479569de stm32/boards/STM32F769DISC: Use external QSPI flash to store some code.
This demonstrates how to use external QSPI flash in XIP (execute in place)
mode.  The default configuration has all extmod/ code placed into external
QSPI flash, but other code can easily be put there by modifying the custom
f769_qspi.ld script.
2019-03-04 22:40:15 +11:00
Damien George
ed0a530614 stm32/boards/STM32F769DISC: Enable lwIP and Ethernet peripheral. 2019-02-26 23:32:19 +11:00
Damien George
1669e049de stm32/boards/STM32F769DISC: Configure for use with mboot by default.
This is a good board to demonstrate the use of Mboot because it only has a
USB HS port exposed so the native ST DFU mode cannot be used.  With Mboot
this port can be used.
2019-02-07 16:28:01 +11:00
Damien George
be1b1835c3 stm32/boards/STM32F769DISC: Support the use of USB HS with external PHY. 2019-02-07 16:26:46 +11:00
Andrew Leech
338635ccc6 stm32/main: Add configuration macros for board to set heap start/end.
The macros are MICROPY_HEAP_START and MICROPY_HEAP_END, and if not defined
by a board then the default values will be used (maximum heap from SRAM as
defined by linker symbols).

As part of this commit the SDRAM initialisation is moved to much earlier in
main() to potentially make it available to other peripherals and avoid
re-initialisation on soft-reboot.  On boards with SDRAM enabled the heap
has been set to use that.
2018-10-05 17:30:18 +10:00
Damien George
a5b583adfd stm32/boards/STM32F769DISC: Add optional support for external SDRAM. 2018-09-20 11:42:03 +10:00
Damien George
a7ebac2eae stm32/can: Allow CAN pins to be configured per board.
This patch allows a given board to configure which pins are used for the
CAN peripherals, in a similar way to all the other bus peripherals (I2C,
UART, SPI).  To enable CAN on a board the mpconfigboard.h file should
define (for example):

    #define MICROPY_HW_CAN1_TX (pin_B9)
    #define MICROPY_HW_CAN1_RX (pin_B8)
    #define MICROPY_HW_CAN2_TX (pin_B13)
    #define MICROPY_HW_CAN2_RX (pin_B12)

And the board config file should no longer define MICROPY_HW_ENABLE_CAN.
2018-04-11 16:35:24 +10:00
Damien George
ed75b2655f stm32/Makefile: Allow a board to config either 1 or 2 firmware sections.
This patch forces a board to explicitly define TEXT1_ADDR in order to
split the firmware into two separate pieces.  Otherwise the default is now
to produce only a single continuous firmware image with all ISR, text and
data together.
2018-03-27 21:24:15 +11:00
Damien George
7aec06ca9a stm32/boards: Allow boards to have finer control over the linker script.
This patch allows a particular board to independently specify the linker
scripts for 1) the MCU memory layout; 2) how the different firmware
sections are arranged in memory.  Right now all boards follow the same
layout with two separate firmware section, one for the ISR and one for the
text and data.  This leaves room for storage (filesystem data) to live
between the firmware sections.

The idea with this patch is to accommodate boards that don't have internal
flash storage and only need to have one continuous firmware section.  Thus
the common.ld script is renamed to common_ifs.ld to make explicit that it
is used for cases where the board has internal flash storage.
2018-03-27 21:17:48 +11:00
Damien George
34911f1a57 stm32/boards: Update all boards to work with new USB configuration. 2018-02-13 18:57:01 +11:00
Damien George
02f88cb2df stm32/boards: Remove all config options that are set to defaults.
mpconfigboard_common.h now sets the defaults so there is no longer a need
to explicitly list all configuration options in a board's mpconfigboard.h
file.
2018-02-09 18:40:40 +11:00
Damien George
01dd7804b8 ports: Make new ports/ sub-directory and move all ports there.
This is to keep the top-level directory clean, to make it clear what is
core and what is a port, and to allow the repository to grow with new ports
in a sustainable way.
2017-09-06 13:40:51 +10:00