Commit Graph

8 Commits

Author SHA1 Message Date
Philipp Ebensberger
0d7366c912 mimxrt: Rework flash configuration.
- Moves definition of BOARD_FLASH_SIZE and other header files related to
	flash configuration into the Makefile.
- Adds board specific clock_config.h.
- Adds board.h, pin_mux.h, and peripherals.h as they are
	required by NXP MCU SDK in order to use our own clock_config.h.
- Renames board specific FlexSPI configuration files.
- Updates flash frequency of MIMXRT1020_EVK
- Creates separated flash_config files for QSPI NOR and
	QSPI Hyper flash.
- Unifies VFS start address to be @ 1M for 1010 and 1020 boards.
- Unifies 1050EVK boards
- Adds support to both NOR and HyperFlash on boards with
	both capabilities.
- Adds automatic FlexRAM initialization to start-up code based on
	linker script and NXP HAL.
- Applies code formatting to all files in mimxrt port.

With this change the flash configuration is restructured and
organized. This simplifies the configuration process and
provides a better overview of each board's settings. With the integration
of clock_config.h, board.h, pin_mux.h, and peripherals.h we gain better
control of the settings and clock configurations. Furthermore the
implementation of an explicit FlexRAM setup improves the system
performance and allows for performance tuning.

Signed-off-by: Philipp Ebensberger
2021-09-14 13:52:52 +02:00
Philipp Ebensberger
87f97e490c mimxrt/sdcard: Implement SDCard driver.
- Configures `PLL2->PFD0` with **198MHz** as base clock of
	`USDHCx` peripheral.
- Adds guards for SDCard related files via `MICROPY_PY_MACHINE_SDCARD`
- Adds creation of pin defines for SDCard to make-pins.py
- Adds new configuration option for SDCard peripheral pinout
        to mpconfigport.h
- Adds interrupt handling support instead of polling
- Adds support for `ADMA2` powered data transfer
- Configures SDCard to run in HS (high-speed mode) with **50MHz** only!

SDCard support is optional and requires `USDHC` peripheral.
Thus this driver is not available on `MIMXRT1010_EVK`.
SDCard support is enabled by setting `MICROPY_PY_MACHINE_SDCARD = 1`
in mpconfigboard.mk.

Signed-off-by: Philipp Ebensberger
2021-09-07 20:45:33 +02:00
robert-hh
1074c784b0 mimxrt: Add support for Hyperflash chips.
Hyperflash is used by the MIMXRT1050_EVKB, MIMXRT1060_EVK and
MIMXRT1064_EVK boards.

This commit includes:
- add support for Hyperflash
- modify MIMXRT1060_EVK and MIMXRT1064_EVK to change from QSPI to
  hyperflash.
- minor incidental changes to other boards so they still build

Note: Erasing a sector on the hyperflash is slow. It takes about a second,
which seems too long, but matches the data sheet.
2021-07-31 16:25:40 +10:00
robert-hh
98c5703027 mimxrt/machine_i2c: Add hardware-based machine.I2C to machine module.
It uses non-blocking transfer of data.  Advantage over SoftI2C:
- Higher data rate up to ~3 MHZ.
- Full protocol support.
2021-07-15 00:36:31 +10:00
robert-hh
f45412793e mimxrt/machine_spi: Add the SPI class to the machine module.
This class supports SPI bus controller mode, with blocking transfers.

SPI device numbers start at 0, to comply with the pinout of the Teensy
boards.  With the configured clock frequency the fastest baud rate is
33MHz.  For messages longer 16 bytes DMA is used.  The class uses the
existing framework with extmod/machine_spi.c.

Extended driver options:

- drive=n with n being between 1 and 6 or PIN.POWER_1 to PIN.POWER_6.
  Since the pins used by the SPI are fixed, no Pin settings can be made.
  Thus the drive option is added allowing to control ringing and crosstalk
  on the connection.

- gap_ns=nnnnn is the time between sent data items in a frame given in ns.
  Default is 2 clock cycles.
2021-06-26 22:14:47 +10:00
robert-hh
7417c6ac91 mimxrt/machine_pin: Implement pin.irq() functionality. 2021-06-16 01:42:10 +10:00
robert-hh
689476c576 mimxrt/machine_uart: Add the UART class to the machine module.
The implementation uses the LPUARTx devices.  Up to 8 UARTs can be used,
given that the pins are accessible.  E.g. 8 on Teensy 4.1, 5 on
MIMXRT1020_EVK.

For Tennsy 4.0 and 4.1 the UART numbers are as printed on the pinout 1..N.
The MIMXRT10xx-EVK boards have only one UART named, which gets the number
1.  All other UART are assigned to different Pins:

MIMXRT1010-EVK:
    D0/D1   UART 1
    D6/D7   UART 2
    A0/D4   UART 3

MIMXRT1020-EVK:
    D0/D1   UART 1
    D6/D9   UART 2
    D10/D12 UART 3
    D14/D15 UART 4
    A0/A1   UART 5

MIMXRT1050-EVK, MIMXRT1060-EVK, MIMXRT1064-EVK:
    D0/D1   UART 1
    D7/D6   UART 2
    D8/D9   UART 3
    A1/A0   UART 4
2021-06-16 01:21:15 +10:00
robert-hh
53fea8598e mimxrt/boards: Add board configuration files for Teensy 4.1.
These are at the moment more or less identical to the Teensy 4.0 files,
except for the pins.csv file and the flash size.
2021-06-04 01:00:39 +10:00