For all but the last pass the assembler only needs to count how much space
is needed for the machine code, it doesn't actually need to emit anything.
The dummy_data just uses unnecessary RAM and without it the code is not
any more complex (and code size does not increase for Thumb and Xtensa
archs).
This patch moves some common code from the individual inline assemblers to
the compiler, the code that calls the emit-glue to assign the machine code
to the functions scope.
This patch adds the MICROPY_EMIT_INLINE_XTENSA option, which, when
enabled, allows the @micropython.asm_xtensa decorator to be used.
The following opcodes are currently supported (ax is a register, a0-a15):
ret_n()
callx0(ax)
j(label)
jx(ax)
beqz(ax, label)
bnez(ax, label)
mov(ax, ay)
movi(ax, imm) # imm can be full 32-bit, uses l32r if needed
and_(ax, ay, az)
or_(ax, ay, az)
xor(ax, ay, az)
add(ax, ay, az)
sub(ax, ay, az)
mull(ax, ay, az)
l8ui(ax, ay, imm)
l16ui(ax, ay, imm)
l32i(ax, ay, imm)
s8i(ax, ay, imm)
s16i(ax, ay, imm)
s32i(ax, ay, imm)
l16si(ax, ay, imm)
addi(ax, ay, imm)
ball(ax, ay, label)
bany(ax, ay, label)
bbc(ax, ay, label)
bbs(ax, ay, label)
beq(ax, ay, label)
bge(ax, ay, label)
bgeu(ax, ay, label)
blt(ax, ay, label)
bnall(ax, ay, label)
bne(ax, ay, label)
bnone(ax, ay, label)
Upon entry to the assembly function the registers a0, a12, a13, a14 are
pushed to the stack and the stack pointer (a1) decreased by 16. Upon
exit, these registers and the stack pointer are restored, and ret.n is
executed to return to the caller (caller address is in a0).
Note that the ABI for the Xtensa emitters is non-windowing.
This patch allows esp8266 to use @micropython.native and
@micropython.viper function decorators. By default the executable machine
code is written to the space at the end of the iram1 region. The user can
call esp.set_native_code_location() to make the code go to flash instead.
If a port defines MP_PLAT_COMMIT_EXEC then this function is used to turn
RAM data into executable code. For example a port may want to write the
data to flash for execution. The function must return a pointer to the
executable data.
The 512k build recently overflowed because of the newly-enabled uselect
module. uselect is arguable more important than framebuf for small
devices so we disable framebuf to keep the 512k build within its limit.
This is a pure refactoring (and simplification) of code so that stmhal
uses the software SPI class provided in extmod, for the machine.SPI
implementation.
So long as a port defines relevant mp_hal_pin_xxx functions (and delay) it
can make use of this software SPI class without the need for additional
code.
Previous to this patch trying to construct, but not init, a UART that
didn't exist on the target board would actually succeed. Only when
initialising the UART would it then raise an exception that the UART does
not exist.
This patch adds an explicit check that the constructed UART does in fact
exist for the given board.
This follows the pattern of other peripherals (I2C, SPI) to specify the
pins using pin objects instead of a pair of GPIO port and pin number. It
makes it easier to customise the UART pins for a particular board.
These are basic drawing primitives. They work in a generic way on all
framebuf formats by calling the underlying setpixel or fill_rect C-level
primitives.
The STM32 F7 and L4 boards use significantly different code to the F4
boards so it's important to test them with CI. To keep CI build times
within a reasonable limit the STM32F4DISC board is no longer built, it's
anyway very similar to the standard F4 build for PYBv1.0.
If you have longish operations on the db (such as logging data) it may
be desirable to periodically sync the database to the disk. The added
btree.sync() method merely exposes the berkley __bt_sync function to the
user.
The constants MP_IOCTL_POLL_xxx, which were stmhal-specific, are moved
from stmhal/pybioctl.h (now deleted) to py/stream.h. And they are renamed
to MP_STREAM_POLL_xxx to be consistent with other such constants.
All uses of these constants have been updated.
