Commit Graph

136 Commits

Author SHA1 Message Date
robert-hh
bbe25f4704 mimxrt: Support selection of PHY type and address.
Useful for boards without a PHY interface, where that has to be
attached. Like the Seed ARCH MIX board or Vision SOM. Phy drivers
supported so far are:

- KSZ8081
- DP83825
- LAN8720

More to come. Usage e.g.:
lan = LAN(phy_type=LAN.PHY_LAN8720, phy_addr=1)

The default values are those set in mpconfigboard.h.
2021-12-14 08:07:52 +01:00
robert-hh
bc1b0fd2c1 mimxrt: Define UART 0 on MIMXRT boards.
UART 0 is attached to the Debug USB port. The settings are
115200 Baud, 8N1.
For MIMXRT1010_EVK this is identical to UART1. For the other boards,
this is an additional UART.
2021-12-14 08:07:52 +01:00
robert-hh
81f706aee4 mimxrt: Support PWM using the FLEXPWM and QTMR modules.
Frequency range 15Hz/18Hz to > 1 MHz, with decreasing resolution of the
duty cycle.  The basic API is supported as documentated, except that
keyword parameters are accepted for both the instatiaton and the
PWM.init() call.

Extensions: support PWM for channel pairs.  Channel pairs are declared by
supplying 2-element tuples for the pins.  The two channels of a pair must
be the A/B channel of a FLEXPWM module.  These form than a complementary
pair.

Additional supported keyword arguments:

- center=value Defines the center position of a pulse within the pulse
  cycle.  The align keyword is actually shortcut for center.

- sync=True|False: If set to True, the channels will be synchronized to a
  submodule 0 channel, which has already to be enabled.

- align=PWM.MIDDLE | PMW.BEGIN | PWM.END. It defines, whether synchronized
  channels are Center-Aligned or Edge-aligned.  The channels must be either
  complementary a channel pair or a group of synchronized channels.  It may
  as well be applied to a single channel, but withiout any benefit.

- invert= 0..3. Controls ouput inversion of the pins.  Bit 0 controls the
  first pin, bit 1 the second.

- deadtime=time_ns time of complementary channels for delaying the rising
  slope.

- xor=0|1|2 xor causes the output of channel A and B to be xored.  If
  applied to a X channel, it shows the value oif A ^ B.  If applied to an A
  or B channel, both channel show the xored signal for xor=1.  For xor=2,
  the xored signal is split between channels A and B.  See also the
  Reference Manual, chapter about double pulses.  The behavior of xor=2 can
  also be achieved using the center method for locating a pulse within a
  clock period.

The output is enabled for board pins only.

CPU pins may still be used for FLEXPWM, e.g. as sync source, but the signal
will not be routed to the output.  That applies only to FLEXPWM pins.  The
use of QTMR pins which are not board pins will be rejected.

As part of this commit, the _WFE() statement is removed from
ticks_delay_us64() to prevent PWM glitching during calls to sleep().
2021-11-24 13:48:27 +11:00
robert-hh
7d7d29dbe2 mimxrt: Fix mp_hal_quiet_timing_enter()/exit() so timer still runs.
The initial code disabled IRQs, which caused the us-ticks timer to stop.
The change here changes the priotity level, such that the timer still runs.
2021-11-16 23:20:06 +11:00
robert-hh
7cc9b257a9 mimxrt/boards: Update the board.json files and add deploy_xx.md files.
- Add board.md files for MIMXRT1060_EVK and MIMXRT1064_EVK warning about
  their experimental state.
- Add separate deploy_teensy.md and deploy_mimxrt.md files.
2021-11-16 23:17:42 +11:00
robert-hh
d72d699dad mimxrt/boards: Add the Seeed ARCH MIX board.
The ARCH MIX board exposes the Ethernet Pins at it's connectors.  Therefore
the software is configured for using a LAN8720 PHY device.  Breakout boards
with the LAN8720 are easily available.
2021-11-16 23:11:21 +11:00
Mike Causer
7f14344428 ports: Add images, features and urls to board.json. 2021-10-28 15:25:38 +11:00
Jim Mussared
e359b077dd ports: Add board.json for all boards.
This will be used by https://micropython.org/download/ to generate the
full listing of boards and firmware files.

Optionally supports a board.md for additional customisation of the
download page, as well as deploy.md for flashing instructions.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2021-10-27 14:04:53 +11:00
robert-hh
9f6604eb27 mimxrt: Enable the platform module. 2021-10-25 23:54:52 +11:00
robert-hh
4f89c38a6a mimxrt: Optimize the runtime speed.
By moving code to ITCM, like vm, gc, parse, runtime.  The change affects
mostly the execution speed of MicroPython code.  The speed is increased by
up to a factor of 6, especially for MCU with small cache.
2021-10-25 23:54:47 +11:00
robert-hh
90b45efa6a mimxrt/boards/make-pins.py: Allow empty lines and comments in pins.csv. 2021-10-25 23:53:51 +11:00
robert-hh
6754213a9d mimxrt/modmachine: Implement soft_reset() and unique_id() functions. 2021-10-25 23:53:48 +11:00
robert-hh
a12e318948 mimxrt/mpconfigport.h: Enable f-strings. 2021-10-25 23:52:35 +11:00
robert-hh
c827d4b7ab mimxrt: Extend the help() message and README.md. 2021-10-25 23:52:08 +11:00
robert-hh
e7572776c3 mimxrt: Add dht_readinto() to the mimxrt module, and freeze dht.py.
The change affects dht.py from the drivers directory as well to include the
logic for the mimxrt port.
2021-10-25 23:49:28 +11:00
robert-hh
99221cd118 mimxrt: Fix cycle counter for time.ticks_cpu() and machine.bitstream().
Prior to this commit mp_hal_ticks_cpu() was not started properly.  It only
started when the code was executed with a debugger attached, except for the
Teensy (i.MXRT1062) boards.  As an additional fix, the CYYCNT timer is now
started at boot time.

Also rename mp_hal_ticks_cpu_init() to mp_hal_ticks_cpu_enable().
2021-10-25 15:50:44 +11:00
robert-hh
06d1b02014 mimxrt/dma_channel: Fix the DMA channel management.
The MIMXRT1011 has only 16 channels, so size the channel list accordingly.
2021-10-25 15:50:44 +11:00
robert-hh
101d2ddea3 mimxrt/hal: Remove duplicate definitions from flexspi_hyper_flash.h. 2021-10-25 15:50:44 +11:00
robert-hh
68146aa197 mimxrt/boards: Fix the D14/D15 pin assignment of MIMXRT1050/60/64_EVK.
There are several PCB layouts in the market under the same name.
2021-10-25 15:50:38 +11:00
robert-hh
c2e4759cfa mimxrt/modmachine: Implement machine.WDT() and machine.reset_cause().
The API follows that of rp2, stm32, esp32, and the docs.

    wdt=machine.WDT(0, timeout)

        Timeout is given in ms. The valid range is 500 to 128000 (128
        seconds) with 500 ms granularity. Values outside of that range will
        be silently aligned.

    wdt.feed()

        Resets the watchdog timer (feeding).

    wdt.timeout_ms(value)

        Sets a new timeout and feeds the watchdog.

        This is a new, preliminary method which is not yet documented.

    reset_cause = machine.reset_cause()

        Values returned:

        1  Power On reset
        3  Watchdog reset
        5  Software reset: state after calling machine.reset()

More elaborate API functions are supported by the MCU, like an interrupt
called a certain time after feeding.  But for port cosistency that is not
implemented.
2021-10-25 15:43:56 +11:00
robert-hh
1866ed7e2e mimxrt/eth: Add LAN support and integrate the network module.
This commit implements 10/100 Mbit Ethernet support in the mimxrt port.

The following boards are configured without ETH network:
- MIMXRT1010_EVK
- Teensy 4.0

The following boards are configured with ETH network:
- MIMXRT1020_EVK
- MIMXRT1050_EVK
- MIMXRT1060_EVK
- MIMXRT1064_EVK
- Teensy 4.1

Ethernet support tested with TEENSY 4.1, MIMRTX1020_EVK and MIMXRT1050_EVK.
Build tested with Teensy 4.0 and MIMXRT1010_EVK to be still working.
Compiles and builds properly for MIMXRT1060_EVK and MIMXRT1064_EVK, but not
tested lacking suitable boards.

Tested functions are:
- ping works bothway
- simple UDP transfer works bothway
- ntptime works
- the ftp server works
- secure socker works
- telnet and webrepl works

The MAC address is 0x02 plus 5 bytes from the manifacturing info field,
which can be considered as unique per device.

Some boards do not wire the RESET and INT pin of the PHY transceiver.  For
operation, these are not required.  If they are defined, they will be used.
2021-10-25 15:14:26 +11:00
Philipp Ebensberger
7e62c9707a mimxrt/sdram: Add SDRAM support.
Adds support for SDRAM via `SEMC` peripheral. SDRAM support can be
enabled in the mpconfigboard.mk file by setting `MICROPY_HW_SDRAM_AVAIL`
to `1` and poviding the size of the RAM via `MICROPY_HW_FLASH_SIZE`.

When SDRAM support is enabled the whole SDRAM is currently used used
for MicroPython heap.

Signed-off-by: Philipp Ebensberger
2021-10-22 08:23:24 +02:00
Philipp Ebensberger
0d7366c912 mimxrt: Rework flash configuration.
- Moves definition of BOARD_FLASH_SIZE and other header files related to
	flash configuration into the Makefile.
- Adds board specific clock_config.h.
- Adds board.h, pin_mux.h, and peripherals.h as they are
	required by NXP MCU SDK in order to use our own clock_config.h.
- Renames board specific FlexSPI configuration files.
- Updates flash frequency of MIMXRT1020_EVK
- Creates separated flash_config files for QSPI NOR and
	QSPI Hyper flash.
- Unifies VFS start address to be @ 1M for 1010 and 1020 boards.
- Unifies 1050EVK boards
- Adds support to both NOR and HyperFlash on boards with
	both capabilities.
- Adds automatic FlexRAM initialization to start-up code based on
	linker script and NXP HAL.
- Applies code formatting to all files in mimxrt port.

With this change the flash configuration is restructured and
organized. This simplifies the configuration process and
provides a better overview of each board's settings. With the integration
of clock_config.h, board.h, pin_mux.h, and peripherals.h we gain better
control of the settings and clock configurations. Furthermore the
implementation of an explicit FlexRAM setup improves the system
performance and allows for performance tuning.

Signed-off-by: Philipp Ebensberger
2021-09-14 13:52:52 +02:00
robert-hh
61b7c098b9 mimxrt/machine_bitstream: Add bitstream function to machine module.
Following the code example for ESP32 of Jim Mussard.

As a side effect:
- mp_hal_ticks_cpu() was implemented,
- mp_hal_get_cpu_freq() and mp_hal_ticks_cpu_init() were added and used.
- mp_hal_pin_high() and mp_hal_pin_low() were changed for symmetry
2021-09-10 13:32:53 +10:00
Philipp Ebensberger
87f97e490c mimxrt/sdcard: Implement SDCard driver.
- Configures `PLL2->PFD0` with **198MHz** as base clock of
	`USDHCx` peripheral.
- Adds guards for SDCard related files via `MICROPY_PY_MACHINE_SDCARD`
- Adds creation of pin defines for SDCard to make-pins.py
- Adds new configuration option for SDCard peripheral pinout
        to mpconfigport.h
- Adds interrupt handling support instead of polling
- Adds support for `ADMA2` powered data transfer
- Configures SDCard to run in HS (high-speed mode) with **50MHz** only!

SDCard support is optional and requires `USDHC` peripheral.
Thus this driver is not available on `MIMXRT1010_EVK`.
SDCard support is enabled by setting `MICROPY_PY_MACHINE_SDCARD = 1`
in mpconfigboard.mk.

Signed-off-by: Philipp Ebensberger
2021-09-07 20:45:33 +02:00
Damien George
d41f6dde56 extmod/modonewire: Make _onewire module configurable via macro option.
Signed-off-by: Damien George <damien@micropython.org>
2021-09-02 13:11:23 +10:00
Damien George
afe0634c98 extmod/machine_spi: Make SoftSPI configurable via macro option.
Signed-off-by: Damien George <damien@micropython.org>
2021-09-02 13:11:23 +10:00
Damien George
122d901ef1 extmod/machine_i2c: Make SoftI2C configurable via macro option.
The zephyr port doesn't support SoftI2C so it's not enabled, and the legacy
I2C constructor check can be removed.

Signed-off-by: Damien George <damien@micropython.org>
2021-09-02 13:11:23 +10:00
Philipp Ebensberger
a1dc7277d9 mimxrt/machine_pin: Implement ioctl for Pin.
To make machine.Signal work correctly (among other things).  The solution
is taken over from the rp2 port.

Signed-off-by: Philipp Ebensberger
2021-08-16 15:03:50 +10:00
Damien George
96c6b8cae3 ports: Rename USBD_VID/PID config macros to MICROPY_HW_USB_VID/PID.
For consistency with other board-level config macros that begin with
MICROPY_HW_USB.

Also allow boards in the mimxrt, nrf and samd ports to configure these
values.

Signed-off-by: Damien George <damien@micropython.org>
2021-08-07 23:13:55 +10:00
robert-hh
b2533fe479 mimxrt/boards: Add support for the MIMXRT1050_EVKB board. 2021-07-31 16:26:39 +10:00
robert-hh
1074c784b0 mimxrt: Add support for Hyperflash chips.
Hyperflash is used by the MIMXRT1050_EVKB, MIMXRT1060_EVK and
MIMXRT1064_EVK boards.

This commit includes:
- add support for Hyperflash
- modify MIMXRT1060_EVK and MIMXRT1064_EVK to change from QSPI to
  hyperflash.
- minor incidental changes to other boards so they still build

Note: Erasing a sector on the hyperflash is slow. It takes about a second,
which seems too long, but matches the data sheet.
2021-07-31 16:25:40 +10:00
robert-hh
98c5703027 mimxrt/machine_i2c: Add hardware-based machine.I2C to machine module.
It uses non-blocking transfer of data.  Advantage over SoftI2C:
- Higher data rate up to ~3 MHZ.
- Full protocol support.
2021-07-15 00:36:31 +10:00
Damien George
06277a9169 mimxrt/machine_led: Use mp_raise_msg_varg helper.
Signed-off-by: Damien George <damien@micropython.org>
2021-07-15 00:12:41 +10:00
Damien George
136369d72f all: Update to point to files in new shared/ directory.
Signed-off-by: Damien George <damien@micropython.org>
2021-07-12 17:08:10 +10:00
robert-hh
efa97beb99 tools/autobuild: Add mimxrt port to build scripts for nightly builds.
The firmware for Teensy 4.0, Teensy 4.1 and MIMXRT1020_EVK are created.
Users of other MIMXRT10xx_EVK boards should be able to build the firmware
themselves, they might need specific DEBUG settings.

The Makefile had to be changed in order to build the .bin file as well.
2021-07-01 12:29:16 +10:00
robert-hh
cbc9a591a4 mimxrt/modmachine: Add a few minor methods to the machine module.
Mostly for compatibility reasons:
- idle()
- disable_irq()
- enable_irq()
- time_pulse_us()
2021-06-26 22:27:02 +10:00
robert-hh
552e11bf64 mimxrt/mimxrt_flash: Remove commented-out code. 2021-06-26 22:27:02 +10:00
robert-hh
c8284c9b50 mimxrt/main: Extend the information returned by help(). 2021-06-26 22:27:02 +10:00
robert-hh
4eabff53cb mimxrt/main: Skip running main.py if boot.py failed.
See related #7379.
2021-06-26 22:27:02 +10:00
robert-hh
b35566af79 mimxrt/boards: Set vfs partition start to 1 MBbyte.
This avoids the irritation of the PJRC HalfKay loader on Teensy 4.0.  Block
0 and 1 are properly erased and the additional formatting in the make
script is not required anymore.
2021-06-26 22:27:02 +10:00
robert-hh
a262faa227 mimxrt/moduos: Seed the PRNG on boot using the TRNG. 2021-06-26 22:27:02 +10:00
robert-hh
f45412793e mimxrt/machine_spi: Add the SPI class to the machine module.
This class supports SPI bus controller mode, with blocking transfers.

SPI device numbers start at 0, to comply with the pinout of the Teensy
boards.  With the configured clock frequency the fastest baud rate is
33MHz.  For messages longer 16 bytes DMA is used.  The class uses the
existing framework with extmod/machine_spi.c.

Extended driver options:

- drive=n with n being between 1 and 6 or PIN.POWER_1 to PIN.POWER_6.
  Since the pins used by the SPI are fixed, no Pin settings can be made.
  Thus the drive option is added allowing to control ringing and crosstalk
  on the connection.

- gap_ns=nnnnn is the time between sent data items in a frame given in ns.
  Default is 2 clock cycles.
2021-06-26 22:14:47 +10:00
Krzysztof Adamski
6409bbcb72 mimxrt: Move calc_weekday helper function to timeutils.
This function may be useful for other ports as well so lets move it to
timeutils so it can be reused.

Signed-off-by: Krzysztof Adamski <k@japko.eu>
2021-06-25 10:28:32 +10:00
robert-hh
8edc3aacdd mimxrt/modutime: Extend the time module.
Methods added:
- time.time()
- time.time_ns()
- time.gmtime()
- time.localtime()
- time.mktime()

The rp2 port was uses as the template for the change.
2021-06-16 01:50:09 +10:00
robert-hh
7417c6ac91 mimxrt/machine_pin: Implement pin.irq() functionality. 2021-06-16 01:42:10 +10:00
robert-hh
689476c576 mimxrt/machine_uart: Add the UART class to the machine module.
The implementation uses the LPUARTx devices.  Up to 8 UARTs can be used,
given that the pins are accessible.  E.g. 8 on Teensy 4.1, 5 on
MIMXRT1020_EVK.

For Tennsy 4.0 and 4.1 the UART numbers are as printed on the pinout 1..N.
The MIMXRT10xx-EVK boards have only one UART named, which gets the number
1.  All other UART are assigned to different Pins:

MIMXRT1010-EVK:
    D0/D1   UART 1
    D6/D7   UART 2
    A0/D4   UART 3

MIMXRT1020-EVK:
    D0/D1   UART 1
    D6/D9   UART 2
    D10/D12 UART 3
    D14/D15 UART 4
    A0/A1   UART 5

MIMXRT1050-EVK, MIMXRT1060-EVK, MIMXRT1064-EVK:
    D0/D1   UART 1
    D7/D6   UART 2
    D8/D9   UART 3
    A1/A0   UART 4
2021-06-16 01:21:15 +10:00
robert-hh
3ab8806c0d mimxrt/machine_rtc: Maintain microsecond offset.
The supplied value for microseconds in datetime() will be treated as a
starting value for the reported microseconds.  Due to internal processing
in setting the time, there is an offset about 1 ms.
2021-06-12 23:20:12 +10:00
robert-hh
fd4eec5555 mimxrt/machine_rtc: Change RTC.datetime() tuple to match other ports.
This change moves the datetime tuple format back to the one used by all the
other ports:

    (year, month, day, weekday, hour, minute, second, microsecond)

Weekday is a number between 0 and 6, with 0 assigned to Monday.  It has to
be provided when setting the RTC with datetime(), but will be ignored on
entry and calculated when needed.

The weekday() method was removed, since that is now again a part of the
datetime tuple.

The now() method was updated so it continues to return a tuple that matches
CPython's datetime module.
2021-06-12 23:15:05 +10:00
robert-hh
53fea8598e mimxrt/boards: Add board configuration files for Teensy 4.1.
These are at the moment more or less identical to the Teensy 4.0 files,
except for the pins.csv file and the flash size.
2021-06-04 01:00:39 +10:00
Philipp Ebensberger
b8c65b174f mimxrt/machine_adc: Add the ADC class to the machine module.
This adds the machine.ADC class with the read_u16() method.  make-pins.py
and supporting files are updated to generate ADC information.
2021-06-04 00:51:58 +10:00
robert-hh
bbdc98f72e mimxrt: Enable many Python and some extmod features.
Besides Python features this includes the extmod modules which make use of
the Pin module, especially machine.softSPI, machine.SoftI2C and onewire.
2021-06-04 00:38:18 +10:00
robert-hh
a40e1473dc mimxrt: Add floating point support.
Since not all boards support double fp, all board specific .mk files are
affected too.
2021-06-04 00:37:22 +10:00
robert-hh
2f365d234e mimxrt/machine_rtc: Add the RTC class to the machine module.
Initial version, using the LP RTC clock.  It provides setting the date and
time with rtc.init() or rtc.datetime(), and reading the date and time with
rtc.datetime() or rtc.now().  The method weekday() reports the weekday of
the current date.  It starts with 0 for Monday.

The tuple order for datetime() and now() matches the CPython sequence:
(year, month, day, hour, minute, second, microsecond, TZ).  TZ is ignored
and reported as None.  Microsecond is provided at a best effort.

If a battery is not supplied, the default boot date/time is 1970/1/1 0:0:0.
With a battery, the clock continues to run even when the board is not
powered.  The clock is quite precise.  If not, using rtc.calibration() may
help.
2021-06-03 15:24:04 +10:00
robert-hh
d79105d7c0 mimxrt/machine_timer: Leave the Timer clock source at IPG clock.
Setting it to OSC_CLK interferes the utime module's functionality.  This is
still an area demanding an understanding.
2021-06-03 13:03:02 +10:00
robert-hh
cdd95ce737 mimxrt/machine_timer: Reuse any existing timer objects.
So there is a 1-1 mapping of hardware timer to Python object.
2021-06-03 13:02:51 +10:00
robert-hh
5226d6e1ee mimxrt: Remove __WFE() from MICROPY_EVENT_POLL_HOOK.
The device is unreliable with the WFE included.  This needs further
investigation.
2021-06-03 12:21:36 +10:00
robert-hh
4c407c790f mimxrt: Add the Timer class to the machine module.
It supports three hardware timer channels based on the PIT timers of the
MIMXRT MCU.  The timer id's are 0, 1 and 2.  On soft reboot all active
timers will be stopped via finalisers.
2021-06-02 00:33:13 +10:00
robert-hh
745b4319a2 mimxrt/boards/TEENSY40: Re-create the flash FS after deploy.
This is required since the Teensy Halfkay loader attempts to erase all of
the flash but fails to do so, at least in my tests.  Formatting brings it
back to a known state.
2021-06-01 23:52:45 +10:00
robert-hh
dfd4324eb1 mimxrt: Add flash storage support with VFS and littlefs filesystem.
This commit adds full support for a filesystem on all boards, with a block
device object mimxrt.Flash() and uos.VfsLfs2 enabled.

Main changes are:
- Refactoring of linker scripts to accomodate reserved area for VFS.  VFS
  will take up most of the available flash. 1M is reserved for code.  9K is
  reserved for flash configuration, interrupts, etc.
- Addition of _boot.py with filesystem init code, called from main.c.
- Definition of the mimxrt module with a Flash class in modmimxrt.[ch].
- Implementation of a flash driver class in mimxrt_flash.c.  All flashing
  related functions are stored in ITCM RAM.
- Addition of the uos module with filesystem functions.
- Implementation of uos.urandom() for the sake of completeness of the uos
  module.

It uses sample code from CircuitPython supplied under MIT license, which
uses the NXP SDK example code.

Done in collaboration with Philipp Ebensberger aka @alphaFred who
contributed the essential part to enable writing to flash while code is
executing, among other things.
2021-06-01 23:42:57 +10:00
robert-hh
c303b15f10 mimxrt: Enable frozen modules. 2021-06-01 22:57:09 +10:00
robert-hh
fdaf2b80d9 mimxrt: Add custom help text and enable help("modules"). 2021-06-01 22:52:44 +10:00
robert-hh
c732b80f05 mimxrt: Extend the Pin module for SoftI2C, SoftSPI support.
This change consists mostly of changing and extending the required
definitions in mphalport.h.
2021-05-25 20:43:52 +02:00
Philipp Ebensberger
c326d9a67b mimxrt: Enable built-in help. 2021-05-26 00:12:45 +10:00
Philipp Ebensberger
ff5d39529c mimxrt: Implement machine.Pin class.
- modified pin type from pin_obj_t to machine_pin_obj_t
- created machine_pin.c
- implemented basic version of make-pins.py to genertate pins.c/.h files
  automatically; the only alternate function currently supported is GPIO
- added af.csv files for all supported MCUs
- replaced pins.c/pins.h files with pin.csv for all boards
- implemented on/off/high/low/value/init methods
- Implemented IN/OUT/OPEN_DRAIN modes
- modified LDFLAGS for DEBUG build to get usefull .elf file for debugging

Signed-off-by: Philipp Ebensberger
2021-05-26 00:12:42 +10:00
Damien George
7408ca1d78 mimxrt: Improve ticks and sleep functions using GPT.
SysTick cannot wake the CPU from WFI/WFE so a hardware timer is needed to
keep track of ticks/delay (similar to the nrf port).

Fixes issue #7234.

Signed-off-by: Damien George <damien@micropython.org>
2021-05-18 22:36:32 +10:00
Damien George
e9e9c76ddf all: Rename mp_keyboard_interrupt to mp_sched_keyboard_interrupt.
To match mp_sched_exception() and mp_sched_schedule().

Signed-off-by: Damien George <damien@micropython.org>
2021-04-30 15:13:43 +10:00
Damien George
d0e014aa41 mimxrt: Enable CPYTHON_COMPAT, PY_ASYNC_AWAIT, PY_ATTRTUPLE options.
This change allows running the tests in tests/basics/ without any failures
(but some tests are still skipped).

Signed-off-by: Damien George <damien@micropython.org>
2021-04-14 12:55:53 +10:00
svetelna
23ce25a7c3 mimxrt/boards: Add MIMXRT1050_EVK board, based on MIMXRT1060_EVK. 2021-03-11 16:42:38 +11:00
Damien George
f31c6b4840 mimxrt: Fix USB CDC handling so it works reliably.
On i.MX the SysTick IRQ cannot wake the CPU from a WFI so the CPU was
blocked on WFI waiting for USB data in mp_hal_stdin_rx_chr() even though it
had already arrived (because it may arrive just after calling the check
tud_cdc_available()).  This commit fixes this problem by using SEV/WFE to
indicate that there has been a USB event.

The mp_hal_stdout_tx_strn() function is also fixed so that it doesn't
overflow the USB buffers.

Signed-off-by: Damien George <damien@micropython.org>
2021-02-12 13:48:51 +11:00
Damien George
035d16126a ports: Update to build with new tinyusb.
Signed-off-by: Damien George <damien@micropython.org>
2021-02-12 12:50:36 +11:00
Damien George
7c44354592 ports: Remove def of MP_PLAT_PRINT_STRN if it's the same as the default.
To simplify config, there's no need to specify MP_PLAT_PRINT_STRN if it's
the same as the default definition in py/mpconfig.h.

Signed-off-by: Damien George <damien@micropython.org>
2021-02-04 22:39:17 +11:00
Damien George
18518e26a7 ports: Use correct in/out endpoint size in TUD_CDC_DESCRIPTOR.
The last argument of TUD_CDC_DESCRIPTOR() is the endpoint size (or
wMaxPacketSize), not the CDC RX buffer size (which can be larger than the
endpoint size).

Signed-off-by: Damien George <damien@micropython.org>
2020-10-17 15:49:16 +11:00
Albort Xue
5f50568b1f mimxrt/boards: Add MIMXRT1064_EVK board. 2020-09-09 00:06:33 +10:00
Albort Xue
05e5d411b5 mimxrt/boards: Set __heap_size__ to 0 in MIMXRT1011.ld.
Do not use the traditional C heap in order to save memory, because the
traditional C heap is unused in MicroPython.
2020-06-10 22:49:26 +10:00
Philipp Ebensberger
29e258611a mimxrt/boards: Integrate support for MIMXRT1020_EVK board. 2020-06-09 19:04:23 +10:00
Albort Xue
e0d539f79d mimxrt/boards: Enable LED class for MIMXRT1060_EVK board. 2020-06-09 18:51:08 +10:00
Philipp Ebensberger
6ac05af8e1 mimxrt/tusb_config.h: Preliminary fix for TinyUSB HS endpoint overflow.
Sending more than 64 bytes to the USB CDC endpoint in HS mode will lead to
a hard crash.  This commit fixes the issue, although there may be a better
fix from upstream TinyUSB in the future.
2020-06-08 14:39:21 +10:00
Philipp Ebensberger
02cc4462b7 mimxrt: Add initial impl of machine.LED class, and basic pin support.
This commit implements an LED class with rudimentary parts of a pin C API
to support it.  The LED class does not yet support setting an intensity.

This LED class is put in the machine module for the time being, until a
better place is found.

One LED is supported on TEENSY40 and MIMXRT1010_EVK boards.
2020-06-05 11:47:48 +10:00
Albort Xue
b3bc9808f2 mimxrt/boards: Add MIMXRT1060_EVK board. 2020-05-27 16:49:52 +10:00
Jim Mussared
710426024a all: Factor gchelper code to one place and use it for unix & ARM ports.
No functionality change is intended with this commit, it just consolidates
the separate implementations of GC helper code to the lib/utils/ directory
as a general set of helper functions useful for any port.  This reduces
duplication of code, and makes it easier for future ports or embedders to
get the GC implementation correct.

Ports should now link against gchelper_native.c and either gchelper_m0.s or
gchelper_m3.s (currently only Cortex-M is supported but other architectures
can follow), or use the fallback gchelper_generic.c which will work on
x86/x64/ARM.

The gc_helper_get_sp function from gchelper_m3.s is not really GC related
and was only used by cc3200, so it has been moved to that port and renamed
to cortex_m3_get_sp.
2020-04-29 23:45:19 +10:00
stijn
84fa3312cf all: Format code to add space after C++-style comment start.
Note: the uncrustify configuration is explicitly set to 'add' instead of
'force' in order not to alter the comments which use extra spaces after //
as a means of indenting text for clarity.
2020-04-23 11:24:25 +10:00
stijn
30840ebc99 all: Enable extra conversion warnings where applicable.
Add -Wdouble-promotion and -Wfloat-conversion for most ports to ban out
implicit floating point conversions, and add extra Travis builds using
MICROPY_FLOAT_IMPL_FLOAT to uncover warnings which weren't found
previously.  For the unix port -Wsign-comparison is added as well but only
there since only clang supports this but gcc doesn't.
2020-04-18 22:42:28 +10:00
Damien George
1a3e386c67 all: Remove spaces inside and around parenthesis.
Using new options enabled in the uncrustify configuration.
2020-03-28 23:36:44 +11:00
Jim Mussared
7eea0d8b6c mimxrt: Add MIMXRT1010 board. 2020-03-11 15:36:27 +11:00
Jim Mussared
f46782dde9 mimxrt: Add new, minimal port to NXP i.MX RT series CPUs.
This is an extremely minimal port to the NXP i.MX RT, in the style of the
SAMD port  It's largely based on the TinyUSB mimxrt implementation, using
the NXP SDK.  It currently supports the Teensy 4.0 board with a REPL over
the USB-VCP interface.

This commit also adds the NXP SDK submodule (also from TinyUSB) to
lib/nxp_driver.

Note: if you already have the tinyusb submodule initialized recursively you
will need to run the following as the tinyusb sub-submodules have been
rearranged (upstream):

    git submodule deinit lib/tinyusb
    rm -rf .git/modules/lib/tinyusb
    git submodule update --init lib/tinyusb
2020-03-11 15:34:13 +11:00