Commit Graph

22 Commits

Author SHA1 Message Date
Yuuki NAGAO
a2c02014cd stm32: Modify RCC->APB2ENR directly instead of HAL API.
Also, it is needed only when USB is enabled.

Signed-off-by: Yuuki NAGAO <wf.yn386@gmail.com>
2023-06-27 22:28:31 +09:00
Yuuki NAGAO
7ca3c1d892 stm32: Add USB support for STM32L1 MCUs.
Signed-off-by: Yuuki NAGAO <wf.yn386@gmail.com>
2023-06-27 22:28:31 +09:00
Damien George
61339aa506 stm32: Add initial support for H5 MCUs.
This commit adds initial support for STM32H5xx MCUs.  The following
features have been confirmed to be working on an STM32H573:
- UART over REPL and USB CDC
- USB CDC and MSC
- internal flash filesystem
- machine.Pin
- machine.SPI transfers with DMA
- machine.ADC
- machine.RTC
- pyb.LED
- pyb.Switch
- pyb.rng
- mboot

Signed-off-by: Damien George <damien@micropython.org>
2023-06-15 11:09:20 +10:00
Damien George
c7923b1139 stm32: Add support for USB on G0 MCUs.
Signed-off-by: Damien George <damien@micropython.org>
2023-03-22 16:38:03 +11:00
Damien George
8b3f1d47a6 stm32/powerctrlboot: Provide custom SystemInit for WB55.
Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au>
Signed-off-by: Damien George <damien@micropython.org>
2023-03-08 14:04:14 +11:00
Andrew Leech
2eca86e8fa stm32/powerctrl: Add sleep RCC semaphore management for WB55 MCUs.
Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au>
2023-03-08 11:33:00 +11:00
yn386
427d72667f stm32: Add support for STM32L1 MCUs.
This change adds STM32L1 support to the STM32 port.
2022-09-25 23:56:41 +10:00
Asensio Lorenzo Sempere
010012c7c3 stm32: Add support for G0 MCUs.
This commit adds support for the STM32G0 series of MCUs.

Signed-off-by: Asensio Lorenzo Sempere <asensio.aerospace@gmail.com>
2022-04-28 11:56:15 +10:00
Damien George
e0a0719416 stm32: Add initial support for STM32WL MCUs.
Signed-off-by: Damien George <damien@micropython.org>
2022-02-04 09:43:43 +11:00
Damien George
4a4f269a1a stm32/powerctrlboot: Set HAL uwTickPrio variable when needed.
Signed-off-by: Damien George <damien@micropython.org>
2022-01-31 18:26:55 +11:00
Damien George
f834fef6bb stm32/powerctrl: Support changing frequency on WB MCUs.
This allows changing the frequency to: 100kHz, 200kHz, 400kHz, 800kHz,
1MHz, 2MHz, 4MHz, 8MHz, 16MHz, 32MHz, 64MHz.  For frequencies 2MHz and
below, low power run (LPR) mode is enabled automatically.

Signed-off-by: Damien George <damien@micropython.org>
2021-08-07 23:41:20 +10:00
Jim Mussared
0f28020a68 stm32/powerctrlboot: Acquire HSEM5 on STM32WB during SystemClock_Config.
This is required to allow using WS firmware newer than 1.1.1 concurrently
with USB (e.g. USB VCP).  It prevents CPU2 from modifying the CLK48 config
on boot.

Tested on WS=1.8 FUS=1.1.

See AN5289 and https://github.com/micropython/micropython/issues/6316
2020-09-08 23:53:12 +10:00
Damien George
ce326699d7 stm32/powerctrlboot: Include irq.h to get definitions of IRQ priorities.
irq.h is included by py/mphal.h but it's better to be explicit, eg if mboot
uses powerctrlboot.c.

Signed-off-by: Damien George <damien@micropython.org>
2020-06-22 13:47:48 +10:00
Damien George
69661f3343 all: Reformat C and Python source code with tools/codeformat.py.
This is run with uncrustify 0.70.1, and black 19.10b0.
2020-02-28 10:33:03 +11:00
Damien George
12413e92a3 stm32/powerctrlboot: Fix config of systick IRQ priority on F0/L0/WB MCU.
Prior to this commit the systick IRQ priority was set at lowest priority on
F0/L0/WB MCUs, because it was left at the default and never configured.
This commit ensures the priority is configured and sets it to the highest
priority.
2019-10-21 12:23:41 +11:00
Chris Mason
eb12fa3862 stm32/powerctrlboot: Add support for HSI at 8MHz on F0 MCUs.
For use with F0 MCUs that don't have HSI48.  Select the clock source
explicitly in mpconfigboard.h.

On the NUCLEO_F091RC board use HSE bypass when HSE is chosen because the
NUCLEO clock source is STLINK not a crystal.
2019-09-26 17:34:04 +10:00
Chris Mason
f16e4be3fa stm32/powerctrlboot: Fix clock and PLL selection for HSI48 on F0 MCUs.
Before this patch the UART baudrate on F0 MCUs was wrong because the
stm32lib SystemCoreClockUpdate sets SystemCoreClock to 8MHz instead of
48MHz if HSI48 is routed directly to SYSCLK.

The workaround is to use HSI48 -> PREDIV (/2) -> PLL (*2) -> SYSCLK.

Fixes issue #5049.
2019-09-26 17:32:22 +10:00
Damien George
59b7166d87 stm32: Add initial support for STM32WBxx MCUs.
This new series of MCUs is similar to the L4 series with an additional
Cortex-M0 coprocessor.  The firmware for the wireless stack must be managed
separately and MicroPython does not currently interface to it.  Supported
features so far include: RTC, UART, USB, internal flash filesystem.
2019-07-17 16:33:31 +10:00
Damien George
4096fa397b stm32/powerctrlboot: Increase SYSCLK to 32MHz for L0 MCUs. 2019-07-16 14:46:31 +10:00
Damien George
4c1ad1f691 stm32: Add support for USB on L0 MCUs. 2019-07-16 14:45:53 +10:00
Damien George
c15dc2c4b9 stm32/powerctrl: Move F0's SystemClock_Config to powerctrlboot.c. 2019-07-08 15:23:53 +10:00
Damien George
21ecf8be5f stm32/powerctrl: Move L0's SystemClock_Config to powerctrlboot.c file. 2019-07-08 15:23:53 +10:00