Commit Graph

111 Commits

Author SHA1 Message Date
Damien George
61339aa506 stm32: Add initial support for H5 MCUs.
This commit adds initial support for STM32H5xx MCUs.  The following
features have been confirmed to be working on an STM32H573:
- UART over REPL and USB CDC
- USB CDC and MSC
- internal flash filesystem
- machine.Pin
- machine.SPI transfers with DMA
- machine.ADC
- machine.RTC
- pyb.LED
- pyb.Switch
- pyb.rng
- mboot

Signed-off-by: Damien George <damien@micropython.org>
2023-06-15 11:09:20 +10:00
Damien George
b839acc7d9 stm32/main: Start UART REPL as early as possible.
For debugging purposes, to see output from other peripherals.

Also reset the pyb_stdio_uart state at the end of soft reset, in case it
points to a heap-allocated object.

Signed-off-by: Damien George <damien@micropython.org>
2023-06-15 11:02:49 +10:00
David Grayson
c046b23ea2 shared/runtime/pyexec: Don't allow Ctrl+C to interrupt frozen boot code.
Helps prevent the filesystem from getting formatted by mistake, among other
things.  For example, on a Pico board, entering Ctrl+D and Ctrl+C fast many
times will eventually wipe the filesystem (without warning or notice).

Further rationale: Ctrl+C is used a lot by automation scripts (eg mpremote)
and UI's (eg Mu, Thonny) to get the board into a known state.  If the board
is not responding for a short time then it's not possible to know if it's
just a slow start up (eg in _boot.py), or an infinite loop in the main
application.  The former should not be interrupted, but the latter should.
The only way to distinguish these two cases would be to wait "long enough",
and if there's nothing on the serial after "long enough" then assume it's
running the application and Ctrl+C should break out of it.  But defining
"long enough" is impossible for all the different boards and their possible
behaviour.  The solution in this commit is to make it so that frozen
start-up code cannot be interrupted by Ctrl+C.  That code then effectively
acts like normal C start-up code, which also cannot be interrupted.

Note: on the stm32 port this was never seen as an issue because all
start-up code is in C.  But now other ports start to put more things in
_boot.py and so this problem crops up.

Signed-off-by: David Grayson <davidegrayson@gmail.com>
2023-04-05 10:38:50 +10:00
Damien George
13fcd8440e stm32: Add support for STM32H723 MCUs.
Signed-off-by: Damien George <damien@micropython.org>
2023-03-21 14:02:49 +11:00
Damien George
b981e37ccd stm32/main: Use mp_printf instead of printf for MPY start-up messages.
Signed-off-by: Damien George <damien@micropython.org>
2023-03-09 12:47:45 +11:00
Damien George
8b3f1d47a6 stm32/powerctrlboot: Provide custom SystemInit for WB55.
Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au>
Signed-off-by: Damien George <damien@micropython.org>
2023-03-08 14:04:14 +11:00
Jim Mussared
bad0098a49 stm32: Update to use the open-source lib version of cyw43-driver.
This removes the previous WiFi driver from drivers/cyw43 (but leaves behind
the BT driver), and makes the stm32 port (i.e. PYBD and Portenta) use the
new "lib/cyw43-driver" open-source driver already in use by the rp2 port.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2023-03-01 01:27:12 +11:00
Jim Mussared
94beeabd2e py/obj: Convert make_new into a mp_obj_type_t slot.
Instead of being an explicit field, it's now a slot like all the other
methods.

This is a marginal code size improvement because most types have a make_new
(100/138 on PYBV11), however it improves consistency in how types are
declared, removing the special case for make_new.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-09-19 19:06:15 +10:00
robert-hh
c781899438 stm32/softtimer: Switch to use softtimer code from shared/runtime. 2022-07-19 12:33:19 +10:00
David Lechner
816e4537f2 stm32: Use MP_REGISTER_ROOT_POINTER().
This uses MP_REGISTER_ROOT_POINTER() to register all port-specific root
pointers in the stm32 port.

Signed-off-by: David Lechner <david@pybricks.com>
2022-07-18 13:50:34 +10:00
Damien George
9af6a275dd stm32/boardctrl: Allow boards to override fatal-error handler.
To override it a board must define MICROPY_BOARD_FATAL_ERROR to a function
that takes a string message and does not return.

Signed-off-by: Damien George <damien@micropython.org>
2022-07-08 23:47:29 +10:00
Damien George
63c7593df6 stm32/main: Support SD cards without a partition table.
Signed-off-by: Damien George <damien@micropython.org>
2022-03-22 12:41:15 +11:00
iabdalkader
a00e1e5735 stm32/dac: Deinit all DACs on soft reset.
DAC timed functions continue to run after a soft reset cycle, using
collected memory in the case of write_timed.
2022-01-27 17:10:39 +11:00
Damien George
de43b500bd py/runtime: Allow initialising sys.path/argv with defaults.
If MICROPY_PY_SYS_PATH_ARGV_DEFAULTS is enabled (which it is by default)
then sys.path and sys.argv will be initialised and populated with default
values.  This keeps all bare-metal ports aligned.

Signed-off-by: Damien George <damien@micropython.org>
2021-12-18 00:08:07 +11:00
Jim Mussared
86ce442607 ports: Add '.frozen' as the first entry in sys.path.
Frozen modules will be searched preferentially, but gives the user the
ability to override this behavior.

This matches the previous behavior where "" was implicitly the frozen
search path, but the frozen list was checked before the filesystem.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2021-12-18 00:08:07 +11:00
Damien George
9a1ab2286d stm32/main: Call sdcard_init when only MICROPY_HW_ENABLE_MMCARD enabled.
Otherwise, if MMCARD is enabled and not SDCARD, then the GPIO will not be
configured for SDIO.

Signed-off-by: Damien George <damien@micropython.org>
2021-12-14 10:48:01 +11:00
Peter Boin
e83aa252f7 stm32/main: Run optional frozen module at boot.
If a board specifies a filename via MICROPY_BOARD_FROZEN_BOOT_FILE then
that will be run on start up, before the usual boot.py.
2021-11-22 11:56:24 +11:00
Jan Staal
9e2423e730 stm32: Add support for H7A3(Q)/H7B3(Q), and STM32H73B3I_DK board defn.
This commit is based upon prior work of @dpgeorge and @koendv.

MCU support for the STM32H7A3 and B3 families MCUs:
- STM32H7A3xx
- STM32H7A3xxQ (SMPS)
- STM32H7B3xx
- STM32H7B3xxQ (SMPS)

Support has been added for the STM32H7B3I_DK board.

Signed-off-by: Jan Staal <info@janstaal.com>
2021-09-16 12:29:28 +10:00
iabdalkader
7aab0dc5d8 extmod: Move modnetwork and modusocket from stm32 to extmod.
So they can be used by other ports.
2021-09-15 01:25:12 +10:00
Damien George
9792c9105f stm32/main: Don't unconditionally enable GPIO A,B,C,D clocks.
Rely on them being enabled only when needed.

Signed-off-by: Damien George <damien@micropython.org>
2021-09-02 20:28:53 +10:00
Damien George
96c6b8cae3 ports: Rename USBD_VID/PID config macros to MICROPY_HW_USB_VID/PID.
For consistency with other board-level config macros that begin with
MICROPY_HW_USB.

Also allow boards in the mimxrt, nrf and samd ports to configure these
values.

Signed-off-by: Damien George <damien@micropython.org>
2021-08-07 23:13:55 +10:00
iabdalkader
7649f5fbd2 stm32/sdram: Make SDRAM test cache aware, and optional failure with msg.
* Make SDRAM test cache-aware for newer MCUs.
* Use the defined data bus width (instead of the fixed 8-bits).
* Allow optional failure on error with verbose error messages.
* Test speed is now inverted (test accepts exhaustive instead fast).
2021-07-22 16:47:49 +10:00
Damien George
136369d72f all: Update to point to files in new shared/ directory.
Signed-off-by: Damien George <damien@micropython.org>
2021-07-12 17:08:10 +10:00
Mike Teachman
8a5bfe44a5 esp32,stm32: Add new machine.I2S class for I2S protocol support.
This commit adds I2S protocol support for the esp32 and stm32 ports, via
a new machine.I2S class.  It builds on the stm32 work of blmorris, #1361.

Features include:
- a consistent I2S API across the esp32 and stm32 ports
- I2S configurations supported:
  - master transmit and master receive
  - 16-bit and 32-bit sample sizes
  - mono and stereo formats
  - sampling frequency
  - 3 modes of operation:
    - blocking
    - non-blocking with callback
    - uasyncio
  - internal ring buffer size can be tuned
- documentation for Pyboards and esp32-based boards
- tested on the following development boards:
  - Pyboard D SF2W
  - Pyboard V1.1
  - ESP32 with SPIRAM
  - ESP32

Signed-off-by: Mike Teachman <mike.teachman@gmail.com>
2021-07-05 23:42:25 +10:00
David Lechner
8182f34584 stm32/main: Call mp_deinit() at end of main.
This adds a call to mp_deinit() in the main function of the STM32 port.
This enables the use of MICROPY_PORT_DEINIT_FUNC on that port, as well as
cleaning up the GIL if threading is enabled.
2021-07-01 12:26:40 +10:00
Damien George
74c2c31811 stm32/mpbthciport: Change from systick to soft-timer for BT scheduling.
Instead of using systick the BT subsystem is now scheduled using a soft
timer.  This means it is scheduled only when it is enabled.

Signed-off-by: Damien George <damien@micropython.org>
2021-06-23 13:14:26 +10:00
Damien George
a72b8443ca stm32/boardctrl: Add constants for reset mode values.
And use the same boardctrl.h header for both the application and mboot so
these constants are consistent.

Signed-off-by: Damien George <damien@micropython.org>
2021-04-30 00:31:35 +10:00
Damien George
7b41d7f187 stm32/boardctrl: Give boards control over execution of boot.py,main.py.
This commit simplifies the customisation of the main MicroPython execution
loop (4 macros are reduced to 2), and allows a board to have full control
over the execution (or not) of boot.py and main.py.

For boards that use the default start-up code, there is no functional
change in this commit.

Signed-off-by: Damien George <damien@micropython.org>
2021-04-09 12:44:19 +10:00
Damien George
c33c749f64 stm32/boardctrl: Add MICROPY_BOARD_STARTUP hook.
Signed-off-by: Damien George <damien@micropython.org>
2021-03-11 09:04:36 +11:00
Braiden Kindt
85ea4ac0e5 stm32/main: Fix passing state.reset_mode to init_flash_fs.
state.reset_mode is updated by `MICROPY_BOARD_BEFORE_SOFT_RESET_LOOP` but
not passed to `init_flash_fs`, and so factory reset is not executed on
boards that do not have a bootloader.  This bug was introduced by
4c3976bbca

Fixes #6903.
2021-03-10 23:50:40 +11:00
Damien George
d1f120b142 stm32/main: Introduce MICROPY_HW_FLASH_MOUNT_AT_BOOT config option.
It's enabled by default to retain the existing behaviour.  A board can
disable this option if it manages mounting the filesystem itself, for
example in frozen code.

Signed-off-by: Damien George <damien@micropython.org>
2021-01-29 15:02:55 +11:00
Damien George
d1945cc2b5 stm32/main: Check block 0 and 1 when auto-detecting littlefs.
The superblock for littlefs is in block 0 and 1, but block 0 may be erased
or partially written, so block 1 must be checked if block 0 does not have a
valid littlefs superblock in it.

Prior to this commit, if block 0 did not contain a valid littlefs
superblock (but block 1 did) then the auto-detection would fail, mounting a
FAT filesystem would also fail, and the system would reformat the flash,
even though it may have contained a valid littlefs filesystem.  This is now
fixed.

Signed-off-by: Damien George <damien@micropython.org>
2021-01-29 15:02:55 +11:00
Damien George
061cb1a73a stm32/main: Do extended readblocks call when auto-detecting littlefs.
When littlefs is enabled extended reading must be supported, and using this
function to read the first block for auto-detection is more efficient (a
smaller read) and does not require a cached SPI-flash read.

Signed-off-by: Damien George <damien@micropython.org>
2020-12-18 13:39:28 +11:00
Jim Mussared
61d1e4b01b extmod/nimble: Make stm32 and unix NimBLE ports use synchronous events.
This changes stm32 from using PENDSV to run NimBLE to use the MicroPython
scheduler instead.  This allows Python BLE callbacks to be invoked directly
(and therefore synchronously) rather than via the ringbuffer.

The NimBLE UART HCI and event processing now happens in a scheduled task
every 128ms.  When RX IRQ idle events arrive, it will also schedule this
task to improve latency.

There is a similar change for the unix port where the background thread now
queues the scheduled task.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2020-11-13 17:19:05 +11:00
Damien George
b99300b53e stm32/boardctrl: Define MICROPY_BOARD_EARLY_INIT alongside others.
Signed-off-by: Damien George <damien@micropython.org>
2020-11-11 21:47:13 +11:00
Damien George
4c3976bbca stm32: Add MICROPY_BOARD calls in various places in stm32_main.
For a board to have full configurability of the soft reset loop.

Signed-off-by: Damien George <damien@micropython.org>
2020-11-11 21:41:04 +11:00
Damien George
1e297c8898 stm32/main: Move update_reset_mode to outside the soft-reset loop.
Running the update inside the soft-reset loop will mean that (on boards
like PYBD that use a bootloader) the same reset mode is used each
reset loop, eg factory reset occurs each time.

Signed-off-by: Damien George <damien@micropython.org>
2020-11-11 21:41:04 +11:00
Damien George
97960dc7de stm32: Support C++ code and user C modules written in C++.
Also build user C modules as part of the stm32 CI.

Signed-off-by: Damien George <damien@micropython.org>
2020-10-29 23:35:36 +11:00
Jim Mussared
50e44f477b stm32/main: Peform a clean shutdown of btstack on soft reset.
Not just NimBLE.
2020-04-29 16:45:46 +10:00
Damien George
eae495a714 stm32/main: Fix bug mounting 3rd SD partition.
Fixes issue #5753.
2020-03-12 12:34:31 +11:00
Damien George
ed848553b4 extmod/vfs: Factor out vfs mount-and-chdir helper from stm32. 2020-03-11 14:24:26 +11:00
Damien George
894c550c86 stm32: Refactor bluetooth stack/hci/driver bindings.
This makes a cleaner separation between the: driver, HCI UART and BT stack.
Also updated the naming to be more consistent (mp_bluetooth_hci_*).

Work done in collaboration with Jim Mussared aka @jimmo.
2020-03-10 01:53:42 +11:00
Damien George
69661f3343 all: Reformat C and Python source code with tools/codeformat.py.
This is run with uncrustify 0.70.1, and black 19.10b0.
2020-02-28 10:33:03 +11:00
Andrew Leech
3fe83e4318 stm32/sdram: Fix compile issue from unused sdram startup test flag. 2020-02-18 14:22:03 +11:00
Andrew Leech
ff9a61b5a8 stm32/sdram: Expose the result of sdram startup test in stm32_main.
This means boards can choose to only use it for gc heap if the test passes.
2020-02-04 18:18:41 +11:00
Jim Mussared
b76f0a73bc stm32/main: Fix SKIPSD file detection so SD card is mounted by default.
The condition for skipping was accidentally inverted in
7723dac337

Fixes issue #5400.
2019-12-09 17:01:30 +11:00
Damien George
ba5e4841ec stm32/main: Fix auto creation of pyb.Flash on boot with kw-only args. 2019-11-27 22:47:05 +11:00
Damien George
7897f5d9be stm32/main: Auto detect block device used for main filesystem. 2019-11-26 00:07:09 +11:00
Damien George
7723dac337 stm32: Generalise flash mounting code so it supports arbitrary FS.
This commit refactors and generalises the boot-mount routine on stm32 so
that it can mount filesystems of arbitrary type.  That is, it no longer
assumes that the filesystem is FAT.  It does this by using mp_vfs_mount()
which does auto-detection of the filesystem type.
2019-11-25 18:10:58 +11:00
Damien George
6a64b280d0 stm32: Add support for RF coprocessor on WB55 MCUs.
This requires a BLE wireless stack firmware to be already programmed in the
secure flash area of the device.
2019-11-01 14:52:17 +11:00