Commit Graph

20 Commits

Author SHA1 Message Date
robert-hh
47fa723586 samd/modmachine: Make some machine classes configurable by #defines.
These include ADC, DAC, I2C, SoftI2C, SPI, SoftI2C, PWM, UART, pulse.  This
is useful for devices like the Adafruit Trinket series which have almost no
accessible GPIO pins.

Signed-off-by: robert-hh <robert@hammelrath.com>
2023-05-22 18:39:07 +10:00
robert-hh
7a847bab1e samd/main: Fix sercom deinit ordering in soft-reset.
If sockets were open when calling soft reset, gc_sweep_all() would try to
close them.  In case of e.g. the NINA WiFi handler, connected through SPI,
spi_transfer() would be called for command exchange with the NINA module.
But at that time SerCom was already disabled.

Moving sercom_deinit_all() behind gc_sweep_all() solves this issue.

Signed-off-by: robert-hh <robert@hammelrath.com>
2023-05-22 18:37:35 +10:00
David Grayson
c046b23ea2 shared/runtime/pyexec: Don't allow Ctrl+C to interrupt frozen boot code.
Helps prevent the filesystem from getting formatted by mistake, among other
things.  For example, on a Pico board, entering Ctrl+D and Ctrl+C fast many
times will eventually wipe the filesystem (without warning or notice).

Further rationale: Ctrl+C is used a lot by automation scripts (eg mpremote)
and UI's (eg Mu, Thonny) to get the board into a known state.  If the board
is not responding for a short time then it's not possible to know if it's
just a slow start up (eg in _boot.py), or an infinite loop in the main
application.  The former should not be interrupted, but the latter should.
The only way to distinguish these two cases would be to wait "long enough",
and if there's nothing on the serial after "long enough" then assume it's
running the application and Ctrl+C should break out of it.  But defining
"long enough" is impossible for all the different boards and their possible
behaviour.  The solution in this commit is to make it so that frozen
start-up code cannot be interrupted by Ctrl+C.  That code then effectively
acts like normal C start-up code, which also cannot be interrupted.

Note: on the stm32 port this was never seen as an issue because all
start-up code is in C.  But now other ports start to put more things in
_boot.py and so this problem crops up.

Signed-off-by: David Grayson <davidegrayson@gmail.com>
2023-04-05 10:38:50 +10:00
robert-hh
9c2bc379f1 samd/machine_uart: Use a finaliser to tidy up UART on soft reset.
And use the common sercom_table, saving a few bytes of RAM.
2022-10-25 23:44:49 +11:00
robert-hh
4cf527eb05 samd/main: Initialize readline on start up.
Somehow that was forgotten.
2022-10-06 23:14:21 +11:00
robert-hh
32c973d554 samd/machine_timer: Add machine.Timer based on the shared soft-timer. 2022-10-06 22:52:39 +11:00
robert-hh
4ef2da176f samd/main: Use the common execution mode of boot.py and main.py.
Behaviour is:
- Do not execute main.py if boot.py failed.
- On a forced exit, do a soft reset.
2022-10-06 22:50:56 +11:00
robert-hh
aa870708ac samd/machine_spi: Add the machine.SPI class.
Suported by both SAMD21 and SAMD51.  It follows the generic API, except for
the bits=nn option, which is not implemented (yet).
2022-10-06 22:48:44 +11:00
robert-hh
b33f204529 samd/machine_uart: Add the machine.UART class.
All board pins that have UART's assigned can be used.  Baud rate range is
75 Baud to ~2 MBaud.

No flow control yet, and only RX is buffered.  TX buffer and flow control
may be added later for SAMD51 with its larger RAM and Flash.
2022-10-06 22:48:12 +11:00
robert-hh
4b6f6ccf88 samd/machine_pin: Add pin.irq() to the machine.Pin class.
Its API conforms to the docs.  There are 16 IRQ channels available, which
will be used as assignable to the GPIO numbers.  In most cases, the irq
channel is GPIO_no % 16.
2022-10-06 22:46:53 +11:00
robert-hh
d693758ab2 samd/machine_pwm: Add the machine.PWM class.
Features are:
- 3 to 5 different frequency groups.
- Freq range of 1Hz - 24 MHz.
- Duty rate stays stable on freq change.

Keyword options to the PWM constructor:
- device=n Select a specific PWM device.  If no device is specified, a free
           device is chosen, if available at that pin.
- freq=nnnn
- duty_u16=nnnn
- duty_ns=nnnn
- invert=True/False Allowing two outputs on the same device/channel to have
                    complementary signals.

If both freq and duty are provided, PWM output will start immediately.

Pins at the same device have the same frequency.  If the PWM output number
exceeds the number of channels at the PWM device, the effctive channel_no
is output_no % channel_count.  So with a channel count of 4, output 7 is
assigned to channel 3.  Pins at a certain channel have the same frequency
and duty rate, but may be seperately inverted.
2022-10-06 22:42:55 +11:00
robert-hh
5c7e93ec48 samd/machine_adc: Add the machine.ADC class.
With the method read_u16().  Keyword arguments of the constructor are:
- bits=n    The resolution; default is 12.
- average=n The average of samples, which are taken and cumulated.  The
            default value is 16.  Averaging by hw is faster than averaging
            in code.

The ADC runs at a clock freq 1.5 MHz.  A single 12 bit conversion takes
8 microseconds.
2022-10-06 22:41:44 +11:00
Damien George
6e71cde6aa ports: Use default VFS config for import_stat and builtin_open.
For ports with MICROPY_VFS and MICROPY_PY_IO enabled their configuration
can now be simplified to use the defaults for mp_import_stat and
mp_builtin_open.

This commit makes no functional change, except for the following minor
points:
- the built-in "open" is removed from the minimal port (it previously did
  nothing)
- the duplicate built-in "input" is removed from the esp32 port
- qemu-arm now delegates to VFS import/open

Signed-off-by: Damien George <damien@micropython.org>
2022-05-25 13:04:45 +10:00
Damien George
de43b500bd py/runtime: Allow initialising sys.path/argv with defaults.
If MICROPY_PY_SYS_PATH_ARGV_DEFAULTS is enabled (which it is by default)
then sys.path and sys.argv will be initialised and populated with default
values.  This keeps all bare-metal ports aligned.

Signed-off-by: Damien George <damien@micropython.org>
2021-12-18 00:08:07 +11:00
Peter van der Burg
cd2223b8fe samd: Integrate latest asf4, add help, more time funcs and uPy features.
- Makefile: update to use new ASF4 files, support frozen manifest, and
  include source files in upcoming commits
- boards/manifest.py: add files to freeze
- boards/samd51p19a.ld: add linker script for this MCU
- help.c: add custom help text
- main.c: execute _boot.py, boot.py and main.py on start-up
- modules/_boot.py: startup file to freeze
- modutime.c: add gmtime, localtime, mktime, time functions
- mpconfigport.h: enabled more features for sys and io and modules
- mphalport.h: add mp_hal_pin_xxx macros
- mphalport.c: add mp_hal_stdio_poll
2021-11-19 11:05:05 +11:00
Damien George
a5ac3d5645 samd: Add support for building with user C modules.
Fixes issue #7545.

Signed-off-by: Damien George <damien@micropython.org>
2021-07-22 22:22:03 +10:00
Damien George
136369d72f all: Update to point to files in new shared/ directory.
Signed-off-by: Damien George <damien@micropython.org>
2021-07-12 17:08:10 +10:00
Jim Mussared
710426024a all: Factor gchelper code to one place and use it for unix & ARM ports.
No functionality change is intended with this commit, it just consolidates
the separate implementations of GC helper code to the lib/utils/ directory
as a general set of helper functions useful for any port.  This reduces
duplication of code, and makes it easier for future ports or embedders to
get the GC implementation correct.

Ports should now link against gchelper_native.c and either gchelper_m0.s or
gchelper_m3.s (currently only Cortex-M is supported but other architectures
can follow), or use the fallback gchelper_generic.c which will work on
x86/x64/ARM.

The gc_helper_get_sp function from gchelper_m3.s is not really GC related
and was only used by cc3200, so it has been moved to that port and renamed
to cortex_m3_get_sp.
2020-04-29 23:45:19 +10:00
Damien George
69661f3343 all: Reformat C and Python source code with tools/codeformat.py.
This is run with uncrustify 0.70.1, and black 19.10b0.
2020-02-28 10:33:03 +11:00
Damien George
5f9bd11527 samd: Add new port to Microchip SAMDxx microcontrollers.
Initially supporting SAMD21 and SAMD51.
2019-07-01 17:19:18 +10:00