Among other things, this requires putting bootloader object files in to
their relevant .a archive, so that they can be correctly referenced by the
ESP IDF's linker script.
- Allow configuration by a board of autorefresh number and burst length.
- Increase MPU region size to 8MiB.
- Make SDRAM region cacheable and executable.
"coverage" build uses different BUILD directory comparing to the normal
build. Previously, any build picked up libaxtls.a from normal build's
directory, but that was fixed recently. So, for each build, we must
build axtls explicitly.
This fixes Travis build in particular.
Use overrideable properties instead of hardcoding the use of the
default cl executable used by msvc toolsets. This allows using
arbitrary compiler commands for qstr header generation.
The CLToolExe and CLToolPath properties are used because they are,
even though absent from any official documentation, the de-facto
standard as used by the msvc toolsets themselves.
Requesting a baudrate of X should never configure the peripheral to have a
baudrate greater than X because connected hardware may not be able to
handle higher speeds. This patch makes sure to round the prescaler up so
that the actual baudrate is rounded down.
Prior to this patch, if VBAT was read via ADC.read() or
ADCAll.read_channel(), then it would remain enabled and subsequent reads
of TEMPSENSOR or VREFINT would not work. This patch makes sure that VBAT
is disabled for all cases that it could be read.
This patch in effect renames MICROPY_DEBUG_PRINTER_DEST to
MICROPY_DEBUG_PRINTER, moving its default definition from
lib/utils/printf.c to py/mpconfig.h to make it official and documented, and
makes this macro a pointer rather than the actual mp_print_t struct. This
is done to get consistency with MICROPY_ERROR_PRINTER, and provide this
macro for use outside just lib/utils/printf.c.
Ports are updated to use the new macro name.
The NRF52 define only covers nrf52832, so update the define checks
to use NRF52_SERIES to cover both nrf52832 and nrf52840.
Fixed machine_hard_pwm_instances table in modules/machine/pwm.c
This enables PWM(0) to PWM(3), RTCounter(2), Timer(3) and Timer(4),
in addition to NFC reset cause, on nrf52840.
When waking from stop mode most of the system is still in the same state as
before entering stop, so only minimal configuration is needed to bring the
system clock back online.
A recent version of arm-none-eabi-gcc (8.2.0) will warn about unused packed
attributes in USB_WritePacket and USB_ReadPacket. This patch suppresses
such warnings for this file only.
Works with pins declared normally in mpconfigboard.h, eg. (pin_XX), as well
as (pyb_pin_XX).
Provides new mp_hal_pin_config_alt_static(pin_obj, mode, pull, fn_type)
function declared in pin_static_af.h to allow configuring pin alternate
functions by name at compile time.
This mechanism will scale to to an arbitrary number of pollable objects, so
long as they implement the MP_STREAM_GET_FILENO ioctl. Since ussl objects
pass through ioctl requests transparently to the underlying socket object,
it will allow ussl sockets to be polled. And a user object with uio.IOBase
as a base could support polling.
The code was dereferencing 0x800 and loading a value from there, trying to
use a literal value (not address) defined in the linker script
(_ram_fs_cache_block_size) which was 0x800.
Adding MICROPY_FATFS as makefile flag in order to explicitly
include oofatfs files to be compiled into the build.
The flag is set to 0 by default. Must be set in addition to
MICROPY_VFS and MICROPY_VFS_FAT in mpconfigport.h.
Temporarly solving the issue of
"differ from the size of original declaration [-Werror=lto-type-mismatch]
until linker is fixed in upcomming release of gcc.
Bug is reported by others, and will be fixed in next version of arm-gcc.
However, this patch makes it possible to use modmusic and modimage
with current compilers.
Alternativly, the code can be compiled with LTO=0, but uses valuable 9K
more on this already squeezed target (microbit).
Support added for s132/s140 v6 in linker scripts and boards.
Support removed for s132 v2/3/5.
Download script updated to fetch new stacks and removed the
non-supported ones.
ble_drv.c updated to only handle s110 v8, and s132/s140 v6.
ubluepy updated to continue scanning after each individual scan
report reported to the module to keep old behaviour of the
Scanner class.
This patch generalize the feather52 target to be a board without
an in-built Bluetooth stack or bootloader giving all flash memory to
micropython code.
This way the feather52 target can run any supported Bluetooth LE
stack the port supports for other nrf52832 targets. Hence, this
make Makefiles/linker scripts and BLE driver support easier
to maintain in the future.
Current adoption on top of nrfx only reads the GPIO->IN register.
In order to read back an output state, nrf_gpio_pin_out_read has
to be called.
This patch concatinate the two read functions such that, if
either IN or OUT register has a value 1 it will return this,
else 0.
Updating lib/nrfx submodule to latest version of master to get
the new GPIO API to read pin direction.
(nrfx: d37b16f2b894b0928395f6f56ca741287a31a244)
Cleaning up use of "pyb" module.
Moving the file to a new folder and updating the
makefile accordingly. New module created called
"board" to take over the functionality of the legacy
"pyb" module.
Updating outdated documentation referring to pyb.Pin,
to now point to machine.Pin.
As EasyDMA variant of SPI(M) might clock out an additional byte
in single byte transactions this patch moves the nrf52832 to
use SPI and not SPIM to get more stable data transactions.
Ref: nrf52832 rev2 errata v1.1, suggested workaround is:
"Use the SPI module (deprecated but still available) or
use the following workaround with SPIM ..."
Current nrfx SPIM driver does not contain this workaround,
and in the meanwhile moving back to SPI fixes the issue.
Also, tabbing the nrfx_config.h a bit to make it more readable.
This patch moves the check of SPI configuration before
including any SPI header files. As targets might disable SPI
support, current code ends up in including SPIM if not SPI
is configured. Hence, this is why the check whether the module is
enabled should be done before including headers.
