This patch ensures that integer channel numbers passed to the ADC
constructor (including temperature sensor) are interpreted as raw
channel numbers, and not cause any GPIO pins to be initialized.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
The FIFO reports not only the bytes read, but also 4 error bits. These were
not checked, leading to NUL value read in case of break and possible
garbage bytes being written on parity/framing error.
This patch addresses the issue that NUL bytes are incorrectly read on
break, and at least provides the boilerplate code and comments for error
handling, that may be implemented in the future.
Signed-off-by: Maarten van der Schrieck <maarten@thingsconnected.nl>
Update rtc, machine and powerctrl drivers to support STM32H5 sleep
modes. This makes RTC alarm wakeup working from lightsleep() and
deepsleep().
Changes:
- Determine start reason for machine.reset_cause() in modmachine.c.
- Add proper interrupt clear code in rtc.c.
- Add wakeup functionality in powerctrl_enter_stop_mode(). Remember
and restore voltage scaling level. Restart HSI48 if it was on before
entering sleep mode.
- Clear DBGMCU_CR in SystemClock_Config() as for other variants.
Otherwise debug flags prevent entering sleep mode.
Implementation Notes:
- rtc.c: EXTI_RTSTR1 bits are not present for H5. Code sequence from
G0/G4/L4/WB/WL would be invalid. RTSTR is only defined for external
(GPIO) interrupts. Maybe this is also true for other STM32 variants.
- powerctrl_enter_stop_mode() uses complicated, nested conditionals
to select STM32 variants. To make code slightly better readable,
comment have been added. A non-nested, #if/#elif sequence would
make the code more readable. I leave this to the original authors.
Signed-off-by: Rene Straub <rene@see5.ch>
This fixes the case where e.g.
struct foo_t {
mp_obj_t x;
uint16_t y;
char buf[];
};
will have `sizeof(struct foo_t)==8`, but `offsetof(struct foo_t, buf)==6`.
When computing the size to allocate for `m_new_obj_var` we need to use
offsetof to avoid over-allocating. This is important especially when it
might cause it to spill over into another GC block.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
It's not worth the effort to update these ports to use boardgen.py, but
put a note just in case anyone uses this as a reference for a new port.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This removes previously unused functionality to generate pins_ad_const.h,
as well as the unused handling of pin AF in machine_pin.c.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Minor change to remove support for using numeric IDs for machine.Pin. This
was previously based on the index of the pin in the board csv, but this is
different (and incompatible) with other ports.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This replaces the previous make-pin-table.py with an implementation based
on boardgen.py.
- MICROPY_PY_MACHINE_PIN_BOARD_CPU macro is removed. This isn't optional
on other ports, so no need for it to be optional on SAMD.
- pin_af_table is removed, and lookups just search the cpu dict instead
(this saves N*wordsize bytes of firmware size to have this extra table).
- pins.csv is now BOARD,CPU to match other ports.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This fixes the H7 af.csv files to include the dual-pad information, by
listing the ADCs supported on the _C pad with a C_ADC prefix.
Minimal change to make-pins.py to ignore these entries. This will be
implemented later to emit constants (similar to ADC.CORE_TEMP) to access
these channels.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Requires additions to tools/boardgen.py for stm32 pin generation.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This is now consistent with other ports.
Also renamed `pin_{board/cpu}_pins_locals_dict` to
`machine_pin_{board/cpu}_pins_locals_dict`.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Changes are:
- Pad all cells to make them easier to read.
- Ensure all files have exactly 19 columns (Port,Pin,AF0-15,ADC)
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Fixes are:
- Comment out lines in pins.csv that do not have valid CPU pins.
It's useful to keep these in the file as "documentation" but in order to
make make-pins.py stricter they need to be commented out.
- Fix some typos (missing P prefix) in pins.csv.
This resulted in some missing board pins.
- Fix some typos in af.csv files.
Some typos of "ADC" and some other that were previously ignored.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
For now, this implements the functionality required for esp32 and rp2,
including support for numeric pins, rp2 alternate functions, and rp2
extended pins.
This also updates the rp2 port to use the same structure for pins.h and
pins.csv as for esp32, and moves the pin definitions directly into the
table (rather than having a table of pointers), which is a small code size
improvement.
Support for "hidden" pins in pins.csv is added (matching the stm32
implementation).
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
All ports now use `--board-csv`, `--prefix`, `--output-souce`,
`--output-header` and no longer write to stdout. This matches the esp32
implementation.
Ports that have an AF input use `--af-csv` (to match `--board-csv`).
Any additional output files are now prefixed with `output-` (e.g.
`--output-af-const`).
Default arguments are removed (all makefiles should always specify all
arguments, using default values is likely an error).
Replaced the `af-defs-cmp-strings` and `hdr-obj-decls` args for stm32 with
just `mboot-mode`. Previously they were set on the regular build, now the
logic is reversed so mboot sets it.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
It's not supported on all ports, adds complexity to the build to generate
pins_af.py, and can mostly be replicated just by printing the pin objects.
Remove support for generating pins_af.py from all ports (nrf, stm32,
renesas-ra, mimxrt, rp2).
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The output pins.c can be processed for qstrs like any other C file.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The output pins.c can be processed for qstrs like any other C file.
Also remove af_const from Makefile (unimplemented in make-pins.py) and fix
target dependency on ad_const.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The output pins.c can be processed for qstrs like any other C file.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Qstrs are picked up from the generated pin source files in the usual qstr
processing stage.
Similarly for the stm constant qstrs.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Also remove af-const header, as this is left over from the STM32 version
and unused.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This prevents each port Makefile from having to add an explicit rule for
`build-BOARD/pins_BOARD.c`.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This updates a small number of files that change with ruff-format's (vs
black's) rules.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This improves (decreases) the latency on stdin, on SoCs with built-in USB
and using TinyUSB, like S2 and S3.
Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au>
ESP32-C3 is not Xtensa-based, so build settings are now tailored a bit
better following that fact. ESP-IDF 5.x already adds architecture-specific
modules by itself so there is no need to specify either the `xtensa` or the
`riscv` module in the build settings.
Signed-off-by: Alessandro Gatti <a.gatti@frob.it>
Commit c4e63ace66 enabled the SPI Ethernet
driver and that cost about 13k of firwmare size, pushing the firmware over
the limit of the D2WD and OTA board variants available size.
To fix, disable SPI Ethernet on the D2WD variant, and build the OTA variant
with size optimisation rather than performance optimisation.
Signed-off-by: Damien George <damien@micropython.org>
This port is largely unmaintained, has limited features (the only hardware
support is for GPIO and timer, and no machine module), only supports a
small number of Teensy boards, and can be confused with the mimxrt support
for Teensy 4.x.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Signed-off-by: Damien George <damien@micropython.org>
nic.isconnected() returns now "True", if a) the physical link is up and b)
an IP address is assigned. The latter happens often by DHCP, in which case
an active connection can be assumed. If the IP address is set manually,
nic.isconnected() would report "True" as well, if at least the physical
link is up. This matches WLAN behaviour which returns "True" when the WLAN
has an IP address.
Before, the behaviour of nic.isconneceted() was erratic, returning "True"
sometimes even without a Ethernet cable attached.
Fixes issue #12741.
Signed-off-by: robert-hh <robert@hammelrath.com>
SPI support was not enabled, and was not adapted for esp-idf v5.x. This
change enables SPI ethernet for all boards and adapts the code for esp-idf
v5.x. The change follows the sample implementation of @hemakumarm72, but
adds the changes for the other adapters as well. Further, it simplifies
the code by removing actions from netwwork_lan.c which are done in the
esp-idf drivers later, like setting the default values for .command_bits
and .address_bits, and registering the SPI interface.
Tested with a Wiznet W5500 breakout.
Signed-off-by: robert-hh <robert@hammelrath.com>
Reduces the CPU usage by the PPP thread by sleeping for one tick if
there was nothing to read; preventing the loop using 100% CPU when the
read operation has a zero timeout and immediately returns.
Signed-off-by: Daniël van de Giessen <daniel@dvdgiessen.nl>
Instead use the generic default defined in modbluetooth_nimble.c.
This then also allows custom boards to easily override the default
Bluetooth GAP name.
Signed-off-by: Daniël van de Giessen <daniel@dvdgiessen.nl>
If data is pushed over serial/JTAG too fast we may fill up stdin_ringbuf
and not be able to read all the data out of the serial/JTAG buffer. Thus
we need to explicitly poll and read the serial/JTAG RX buffer to prevent
blocking (since if the serial/JTAG buffer is already filled, we will not
get another interrupt to transfer it to the stdin ringbuffer).
Signed-off-by: Daniël van de Giessen <daniel@dvdgiessen.nl>
PPP code assumes that IPv6 support is enabled. Whilst this is the default,
certain applications may want to disable IPv6 support if not needed (or to
reduce code size).
This makes the code build with CONFIG_LWIP_IPV6 disabled, reducing code by
about 30k in that case.
Signed-off-by: Alessandro Gatti <a.gatti@frob.it>
This provides a way to enable features and changes slated for MicroPython
2.x, by running `make MICROPY_PREVIEW_VERSION_2=1`. Also supported for
the cmake ports (except Zephyr).
This is an alternative to having a 2.x development branch (or equivalently,
keeping a 1.x release branch). Any feature or change that needs to be
"hidden" until 2.x can use this flag (either in the Makefile or the
preprocessor).
A good example is changing function arguments or other public API features,
in particular to aid in improving consistency between ports.
When `MICROPY_PREVIEW_VERSION_2` is enabled, the REPL banner is amended to
say "MicroPython (with v2.0 preview) vX.Y.Z", and sys.implementation gets a
new field `_v2` set to `True`.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The contents of machine_mem.h, machine_i2c.h and machine_spi.h have been
moved into extmod/modmachine.h.
Signed-off-by: Damien George <damien@micropython.org>
The contents of machine_bitstream.h, machine_pinbase.h, machine_pulse.h and
machine_signal.h have been moved into extmod/modmachine.h.
Signed-off-by: Damien George <damien@micropython.org>
The machine_i2c_type, machine_spi_type and machine_timer_type symbols are
already declared in extmod/modmachine.h and should not be declared anywhere
else.
Also move declarations of machine_pin_type and machine_rtc_type to the
common header in extmod.
Signed-off-by: Damien George <damien@micropython.org>
This is a code factoring to have the Python bindings in one location, and
all the ports use those same bindings. For all ports except the two listed
below there is no functional change.
The nrf port has UART.sendbreak() removed, but this method previously did
nothing.
The zephyr port has the following methods added:
- UART.init(): supports setting timeout and timeout_char.
- UART.deinit(): does nothing, just returns None.
- UART.flush(): raises OSError(EINVAL) because it's not implemented.
- UART.any() and UART.txdone(): raise NotImplementedError.
Signed-off-by: Damien George <damien@micropython.org>
No functional change, just code factoring to have the Python bindings in
one location, and all the ports use those same bindings.
Signed-off-by: Damien George <damien@micropython.org>
This commit makes it so that MICROPY_PY_MACHINE_PWM is enabled if at least
one of MICROPY_PY_MACHINE_HW_PWM and/or MICROPY_PY_MACHINE_SOFT_PWM are
enabled. This simplifies the configuration for boards, and fixes DVK_BL652
which enabled PWM without selecting software or hardware implementations.
With this change, DVK_BL652 and EVK_NINA_B1 now enable (hardware) PWM.
Signed-off-by: Damien George <damien@micropython.org>
This factors the basic top-level I2S class code from the ports into
extmod/machine_i2s.c:
- I2S class definition and method table.
- The init and deinit method wrappers.
- The make_new code.
Further factoring will follow.
Signed-off-by: Damien George <damien@micropython.org>
With public declarations moved to extmod/modmachine.h. It's now mandatory
for a port to define MICROPY_PY_MACHINE_PWM_INCLUDEFILE if it enables
MICROPY_PY_MACHINE_PWM. This follows how extmod/machine_wdt.c works.
All ports have been updated to work with this modified scheme.
Signed-off-by: Damien George <damien@micropython.org>
There are currently 7 ports that implement machine.WDT and a lot of code is
duplicated across these implementations. This commit factors the common
parts of all these implementations to a single location in
extmod/machine_wdt.c. This common code provides the top-level Python
bindings (class and method wrappers), and then each port implements the
back end specific to that port.
With this refactor the ports remain functionally the same except for:
- The esp8266 WDT constructor now takes keyword arguments, and accepts the
"timeout" argument but raises an exception if it's not the default value
(this port doesn't support changing the timeout).
- The mimxrt and samd ports now interpret the argument to WDT.timeout_ms()
as signed and if it's negative truncate it to the minimum timeout (rather
than it being unsigned and a negative value truncating to the maximum
timeout).
Signed-off-by: Damien George <damien@micropython.org>
This commit implements Ethernet support for STM32H5. Changes are:
- Add Cortex-M33 MPU code. Ethernet driver requires MPU to define cache
strategy for DMA buffers (descriptors and frames).
- Add support for STM32H5 Ethernet controller. The controller is mostly
compatible with the STM32H7. However the descriptor layout is different.
- Adapt clocking and reset for STM32H5.
Tested on NUCLEO-H563ZI and STM32H573I-DK, using ping and iperf3. TCP
rates of 80-90 Mbits/sec were achievable.
Signed-off-by: Rene Straub <rene@see5.ch>
Signed-off-by: Damien George <damien@micropython.org>
When using malloc and free there were out-of-memory situations depending on
the arm-none-eabi package version. This commit changes malloc/free to use
the MicroPython GC heap instead.
Signed-off-by: robert-hh <robert@hammelrath.com>
Signed-off-by: Damien George <damien@micropython.org>
This workaround fixes an issue with some production boards that have
an older QSPI flash part revision, which can't handle floating pins.
Note those pins can be reconfigured and reused later.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
If a non-string buffer was passed to execfile, then it would be passed
as a non-null-terminated char* to mp_lexer_new_from_file.
This changes mp_lexer_new_from_file to take a qstr instead (as in almost
all cases a qstr will be created from this input anyway to set the
`__file__` attribute on the module).
This now makes execfile require a string (not generic buffer) argument,
which is probably a good fix to make anyway.
Fixes issue #12522.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
That can be caused e.g. by an exception. This feature is implemented in
some way already for the stm32, renesas-ra, mimxrt and samd ports. This
commit adds it for the rp2, esp8266, esp32 and nrf ports. No change for
the cc3200 and teensy ports.
Signed-off-by: robert-hh <robert@hammelrath.com>
For consistency with other Python-level modules.
Also add the corresponding missing preprocessor guard to esp32/modespnow.c,
so that this port compiles if MICROPY_PY_ESPNOW and MICROPY_PY_NETWORK_WLAN
are set to 0.
Fixes#12622.
Signed-off-by: Glenn Moloney <glenn.moloney@gmail.com>
led_init() was not called, and therefore the machine.LED class seemed not
to work. led_init() now uses mp_hal_pin_output() to configure the pin.
Signed-off-by: robert-hh <robert@hammelrath.com>
See https://github.com/micropython/micropython/issues/12127 for details.
Previously at the point when a release is made, we update mpconfig.h
and set a git tag. i.e. the version increments at the release.
Now the version increments immediately after the release. The workflow is:
1. Final commit in the cycle updates mpconfig.h to set (X, Y, 0, 0) (i.e.
clear the pre-release state).
2. This commit is tagged "vX.Y.0".
3. First commit for the new cycle updates mpconfig.h to set (X, Y+1, 0, 1)
(i.e. increment the minor version, set the pre-release state).
4. This commit is tagged "vX.Y+1.0-preview".
The idea is that a nightly build is actually a "preview" of the _next_
release. i.e. any documentation describing the current release may not
actually match the nightly build. So we use "preview" as our semver
pre-release identifier.
Changes in this commit:
- Add MICROPY_VERSION_PRERELEASE to mpconfig.h to allow indicating that
this is not a release version.
- Remove unused MICROPY_VERSION integer.
- Append "-preview" to MICROPY_VERSION_STRING when the pre-release state
is set.
- Update py/makeversionhdr.py to no longer generate MICROPY_GIT_HASH.
- Remove the one place MICROPY_GIT_HASH was used (it can use
MICROPY_GIT_TAG instead).
- Update py/makeversionhdr.py to also understand
MICROPY_VERSION_PRERELEASE in mpconfig.h.
- Update py/makeversionhdr.py to convert the git-describe output into
semver-compatible "X.Y.Z-preview.N.gHASH".
- Update autobuild.sh to generate filenames using the new scheme.
- Update remove_old_firmware.py to match new scheme.
- Update mpremote's pyproject.toml to handle the "-preview" suffix in the
tag. setuptools_scm maps to this "rc0" to match PEP440.
- Fix docs heading where it incorrectly said "vvX.Y.Z" for release docs.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Currently on rp2 the time.time_ns() function has only seconds resolution.
This commit makes it have microsecond resolution, by using the output of
time_us_64() instead of the RTC.
Tested that it does not drift from the RTC over long periods of time.
Signed-off-by: Damien George <damien.p.george@gmail.com>
No other network-enabled board has urllib.urequest frozen in to the
firmware, and esp8266 is relatively low on flash, so remove this module.
And (u)requests is already included by bundle-networking.
Signed-off-by: Damien George <damien@micropython.org>
Also remove corresponding commented line from esp8266/boards/manifest.py.
It doesn't have enough flash to have this frozen by default.
Signed-off-by: Glenn Moloney <glenn.moloney@gmail.com>
Allows using gdb, addr2line, etc. on a "release" ELF file.
No impact to .bin or .uf2 size, only the .elf will get bigger.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
The current code assumes all I2Cs are on the same peripheral bus, which is
not true for I2C4 and the same goes for the clock enable code.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
The IDF-provided version of TinyUSB defaults to Espressif's standard
VID:PID unless specific sdkconfig options are present. The numbers
already defined for the CUSTOM_* config options were ignored otherwise.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
This removes the duplicate code in cyw43, esp32, esp8266 that implements
the same logic as network.hostname.
Renames the `mod_network_hostname` (where we store the hostname value in
`.data`) to `mod_network_hostname_data` to make way for calling the shared
function `mod_network_hostname`.
And uses memcpy for mod_network_hostname_data, because the length of source
is already known and removes reliance on string data being null-terminated.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This changes from the previous limit of 15 characters. Although DHCP and
mDNS allow for up to 63, ESP32 and ESP8266 only allow 32, so this seems
like a reasonable limit to enforce across all ports (and avoids wasting the
additional memory).
Also clarifies that `MICROPY_PY_NETWORK_HOSTNAME_MAX_LEN` does not include
the null terminator (which was unclear before).
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
By clearing the tamper bits and enabling access to the registers for all
code, just in case that this was set. It keeps the clock running on
battery and the calibration setting.
Signed-off-by: robert-hh <robert@hammelrath.com>
Not all boards or BLE extensions have the flow control signals for BLE
available at suitable pins. Actually none of the Adafruit extensions
match for flow control.
For consistency with the previous behaviour it is enabled by default.
Signed-off-by: robert-hh <robert@hammelrath.com>
Commit 552b0bbe12 did not define
MICROPY_PY_MACHINE_SDCARD properly, and thus building the firmware failed.
Signed-off-by: robert-hh <robert@hammelrath.com>
There is a single UART clock for all devices, so switching it for one will
affect all devices used at that time. This commit fixes that issue by
keeping the clock at a fixed value.
This fixed clock still supports the common baud rates between 300 and
921600 baud.
Signed-off-by: robert-hh <robert@hammelrath.com>
This is option is no longer needed as a Makefile option as the USDHC driver
is enabled for all supported series.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
Changes are:
- Disable internal flash storage and use the external QSPI for storage.
- Disable default bootloader entry mode. The bootloader entry function
exists in board_init.c.
- Remove OSC enable/disable macros (this board doesn't have an OSC).
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
This was previously hard-coded to "Micropy" / "Mass Storage" / "1.0".
Now allow it to be overridden by a board.
Also change "Micropy" to "MicroPy" and "1.0" to "1.00" to match stm32.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This was previously hard-coded to "MicroPy" / "pyboard Flash" / "1.00".
Now allow it to be overridden by a board.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Add "CONFIG_BOOTLOADER_APP_ROLLBACK_ENABLE=y" to
ports/esp32/boards/sdkconfig.base so that all micropython esp32 images
support OTA rollback in the bootloader. These images can then be converted
to OTA-capable images as required by user tools.
Also remove CONFIG_BOOTLOADER_APP_ROLLBACK_ENABLE=y from board-specific
sdkconfig files as this is now the default.
Signed-off-by: Glenn Moloney <glenn.moloney@gmail.com>
While cyw43 is deinitialized, an interrupt occurs. That is handled with
these lines: ports/rp2/mpnetworkport.c#L59-L61 and as pendsv is disabled
while in network code, the poll function then just waits there.
When deinit has finished, the poll func is executed, but skipped:
src/cyw43_ctrl.c#L222-L225 this skips the `CYW43_POST_POLL_HOOK` which
would re-enable interrupts, but also reset `cyw43_has_pending`.
And in that state, the lightsleep code, will skip sleeping as it thinks
there is a network packet pending to be handled.
With this change applied, lightsleep works as expected when the wifi chip
is enabled, and when it's powered off.
Applies to newly-added ARDUINO_PORTENTA_C33 and UM_NANOS3.
Makes the list match the standard features defined in
24a6e951ec.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This was copied from minimal/mpconfigport.h, but it doesn't make sense
for general ports.
Add a comment to minimal/mpconfigport.h to explain why it specifically
overrides it.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This provides a way to build a non-DEBUG host binary that still has symbols
and debug information.
Document this for the unix port, and update a comment in the unix port
Makefile.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This gets the calculation working properly for H5 MCUs, and fixes the
switch statement to switch on csel&7 instead of csel&3.
Signed-off-by: Damien George <damien@micropython.org>
The include of HAL headers should come after the HAL configuration defines,
so that the headers can see whether the defines were made or not, to
provide defaults and configure various things.
Signed-off-by: Damien George <damien@micropython.org>
Integrate DAC support for STM32H5. Implement STM32H5 GPDMA driver. The DMA
driver is largely different from other STM32 variants. To support the DAC
circular mode, memory based linked list DMA descriptors are used.
Signed-off-by: Rene Straub <rene@see5.ch>
Changes are:
- Run ADC on PCLK/16.
- Verify and optimize timings (ADC_STAB_DELAY_US, ADC_SAMPLETIME_DEFAULT).
- Add support for STM32H5 VBAT and COREVDD channels on ADC2.
- Replace ADC constants in machine_adc_locals_dict_table.
- Convert STM32 literal to channel numbers in adc_config_channel with
corresponding STM32 LL library functions (__LL_ADC_IS_CHANNEL_INTERNAL(),
__LL_ADC_CHANNEL_TO_DECIMAL_NB()).
Reasoning for the second last point: the STM32 driver literals are uint32_t
that don't work with MP_ROM_INT() which handles signed 31 bit integers
only. Introduce enumerator machine_adc_internal_ch_t to define external
channels (0..19), internal channels (256..) and the special channel VREF
(0xffff). Values are converted to STM32 literals with adc_ll_channel()
when required in adc_config_and_read_u16().
Signed-off-by: Rene Straub <rene@see5.ch>
Select ADC instance based on pin information to support ADC2 inputs.
Display ADC instance number similar to machine_adc (STM32H5 only):
<ADC2 on Pin(Pin.cpu.F14, mode=Pin.ANALOG) channel=6>
Signed-off-by: Rene Straub <rene@see5.ch>
Fixed the preliminary STM32H5 ADC support for pyb.ADC:
- Run ADC on PCLK/16.
- Use STM32 ADC library channel literals (__HAL_ADC_DECIMAL_NB_TO_CHANNEL).
- Use correct temperature conversion for H5 (30C, 130C calibration points).
Signed-off-by: Rene Straub <rene@see5.ch>
To simulate a partial erase, the code reads a native block, erases it,
and writes back the data before and after the erased area. However, the
current logic was filling the area after the erased block with data
from the beginning of the native block-aligned data, instead of applying
the proper offset.
Fixes#12474.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
If a board needs these outputs then it can define MICROPY_HW_CLK_PLLQ/R.
It saves power to not enable them if they are not needed.
Signed-off-by: Damien George <damien@micropython.org>
Currently, check_esp_err() raises an exception without a location in the
source code, eg:
Traceback (most recent call last):
File "<stdin>", line 8, in <module>
OSError: (-258, 'ESP_ERR_INVALID_ARG')
This commit allows additional error reporting (function, line and file) to
be enabled via detailed exceptions. Change the error reporting config to
#define MICROPY_ERROR_REPORTING (MICROPY_ERROR_REPORTING_DETAILED)
and then exception messages from IDF errors look like:
Traceback (most recent call last):
File "<stdin>", line 1, in <module>
OSError: (-258, "0x0102 ESP_ERR_INVALID_ARG in function 'set_duty_u16'
at line 342 in file './machine_pwm.c'")
Signed-off-by: Ihor Nehrutsa <IhorNehrutsa@gmail.com>
Fixes are:
- The baudrate argument is a keyword arg, it was passed before as a
positional arg.
- Use the port and baudrate arguments passed from higher level code instead
of the hard-coded port ID and baudrate, which would allow HCI drivers to
change baudrates.
- Increase UART char timeout and RX buffer size.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
This patch generates a binary firmware image (*.bin) and removes the split
TEXT1/0_ADDR/SECTIONS because it's not configured for this port so it
generates broken binaries.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
Newer MCU series have additional fields in the struct which need to be
initialised to zero, eg Break2AFMode on WB55.
This work was funded by Planet Innovation.
Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au>
sdkconfig.base: Add CONFIG_BOOTLOADER_SKIP_VALIDATE_IN_DEEP_SLEEP=y.
This reduces time to boot from deepsleep by at least 200ms and can
provide significant power savings for deepsleep-based battery
applications.
docs/library/esp32.rst: Add note cautioning not to enter deepsleep after
changing the boot partition, without first performing a hard reset.
Signed-off-by: Glenn Moloney <glenn.moloney@gmail.com>
And use it in the Bluetooth bindings instead of setting the baudrate by a
call to the NXP lib.
Also fixes machine_uart.c to work with a baud rate of 921600.
Signed-off-by: robert-hh <robert@hammelrath.com>
- Superfluous comments in MP_DEFINE_CONST_OBJ_TYPE stop correct macro
expanding.
- MP_ERROR_TEXT now gives mp_rom_error_text_t, but we want plain const
char *.
Signed-off-by: David Yang <mmyangfl@gmail.com>
In CPython, `_thread.start_new_thread()` returns an ID that is the same ID
that is returned by `_thread.get_ident()`. The current MicroPython
implementation of `_thread.start_new_thread()` always returns `None`.
This modifies the required functions to return a value. The native thread
id is returned since this can be used for interop with other functions, for
example, `pthread_kill()` on *nix. `_thread.get_ident()` is also modified
to return the native thread id so that the values match and avoids the need
for a separate `native_id` attribute.
Fixes issue #12153.
Signed-off-by: David Lechner <david@pybricks.com>
When calling ppp.active(False) we could get a crash due to immediately
returning after asking FreeRTOS to delete the current task.
This commit adds a simple blocking loop, the same as used in all other
places where we call vTaskDelete(NULL).
Signed-off-by: Daniël van de Giessen <daniel@dvdgiessen.nl>
Showing the period alway as microsecond quantities, since tick_hz is
assumed as 1_000_000 if the period is given by freq=xxx. If the period is
larger than 0xffffffff, the value is divided by 1000 and "000" is appended
in the display. That works for periods up to about 50 days.
Signed-off-by: robert-hh <robert@hammelrath.com>
Needed for mip to find a default location to install to.
Like esp32, samd uses "/" as the mount point for the flash. Make _boot.py
add the entry after successfully mounting.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
If we're reading from an UART with a non-zero timeout, we can release the
GIL so that other threads/tasks may run while we are sleeping waiting for
data to arrive.
Signed-off-by: Daniël van de Giessen <daniel@dvdgiessen.nl>
CONFIG_USB_OTG_SUPPORTED is automatically set by the ESP-IDF when the chip
supports USB-OTG, which is the case for the ESP32-S2 and ESP32-S3.
When trying to use the JTAG console with these chips, it would not work
because our USB implementation will take over control over the USB port,
breaking the JTAG console in the process.
Thus, when the board is configured to use the JTAG console, we should not
enable our USB console support.
Additionally, this change also frees up UART0 when an USB-based console is
configured, since there's no reason to prevent (re)configuration of UART0
for other uses in that case.
Signed-off-by: Daniël van de Giessen <daniel@dvdgiessen.nl>
This implements support for SO_BINDTODEVICE, which allows telling a socket
to use a specific interface instead of lwIP automatically selecting one.
This allows devices that have multiple connections (for example cellular
over PPP in addition to WLAN) to explicitly choose which data is send over
which connection, which may have different reliability and or (mobile data)
costs associated with using them.
The used lwIP network stack already has support for this, so all that was
needed was to expose this functionality in MicroPython. This commit
exposes a new constant SO_BINDTODEVICE which can be set as an socket
option. As a value it expects the name of the interface to bind to. These
names can be retrieved using `.config('ifname')` implemented on each
interface type (including adding in this commit a `.config()` method to
PPP, which it didn't have before), which returns a string with the
interface name:
>>> import machine
>>> import network
>>> network.WLAN(network.AP_IF).config('ifname')
'lo0'
>>> wlan = network.WLAN(network.AP_IF)
>>> wlan.active(True) and wlan.config('ifname')
'ap1'
>>> wlan = network.WLAN(network.STA_IF)
>>> wlan.active(True) and wlan.config('ifname')
'st1'
>>> ppp = network.PPP(machine.UART(0))
>>> ppp.active(True) and ppp.config('ifname')
'pp1'
>>> ppp = network.PPP(machine.UART(0))
>>> ppp.active(True) and ppp.config('ifname')
'pp2'
>>> ppp = network.PPP(machine.UART(0))
>>> ppp.active(True) and ppp.config('ifname')
'pp3'
Note that lo0 seems to be returned by lwIP if the interface is not yet
active. The method can also return None in the case of PPP where the
entire lwIP interface doesn't yet exist before being activated. Currently
no effort is made to unify those cases; it is expected that whatever we
receive from lwIP is valid.
When the socket option is set, this forces using a specific device:
import socket
s = socket.socket(socket.AF_INET, socket.SOCK_STREAM)
s.setsockopt(socket.SOL_SOCKET, socket.SO_BINDTODEVICE, 'st1')
setsockopt will throw (OSError: [Errno 19] ENODEV) if the specified
interface does not exist.
Tested with LAN, WLAN, and PPP; can specify which interface should be used
and when testing with, for example, HTTP requests to ifconfig.co the
returned IP address confirms a specific interface was used.
Signed-off-by: Daniël van de Giessen <daniel@dvdgiessen.nl>
With using UART FIFO, the timeout should be long enough that FIFO becomes
empty. Since previous data transfer may be ongoing, the timeout must be
timeout_char multiplied by FIFO size + 1.
Signed-off-by: Yuuki NAGAO <wf.yn386@gmail.com>
Since commit 3533924c36 the zlib module has
been replaced by the new deflate module. This commit updates the script
fwupdate.py to use the new deflate module.
Signed-off-by: Oliver Joos <oliver.joos@hispeed.ch>
Down to 50 baud (in reverence to Jean-Maurice-Émile Baudot). Implemented
for the MIMXRT10xx MCU's only. The MIMXRT1176 runs down to 300 baud.
Signed-off-by: robert-hh <robert@hammelrath.com>
The code did not check at deinit whether a UART was initialized. That did
not matter for all MCU's except MIMXRT1176, which crashes at the second
soft reset in a row.
But since it is a general problem to use UART methods of a UART which has
been deinitialized, checks were added to all applicable methods for a clear
response instead of e.g. a crash.
Deinitialize UART using software reset. It resets the UART but keeps it
accessible for software, avoiding an exception when UART registers are
accessed after a DeInit.
Signed-off-by: robert-hh <robert@hammelrath.com>
Following other ports, IRQ priorities and related functions are moved to
their own header, to simplify mpconfigport.h.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
This commit allows other ports to reuse the CYW43 HCI driver, by replacing
all Bluetooth UART and control named pins with defines in config files and
using `mpbthci` abstract functions (i.e. `mp_bluetooth_hci_*`) instead of
the STM32 specific UART functions.
Note: the function `cywbt_wait_cts_low` does not need to switch the CTS
pin from alternate function to GPIO to read it. At least on stm32, mimxrt
it's possible to just read the pin input. For example, see the STM32F7
RM0410 section 6.3.11, and the `SION` for IMXRT. So this function can
also be available for other ports if the pin mode switching is removed.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
This commit adds the necessary configuration and hooks to get the CYW43
driver working with the mimxrt port.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
This is a basic SDIO driver for the mimxrt port, that was added mainly to
support the CYW43 WiFi driver, and as such it only supports the commands
required by the CYW43 driver (but more commands can be added easily). The
driver performs non-blocking DMA transfers, and can detect and recover from
errors.
Note: because the mimxrt port is missing static alternate functions, named
pins and other pin related functions, currently the alternate functions for
USDHC 1 and 2 are hard-coded in the driver.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
Add portable pin config macros to mphalport.h. And add a function to
configure pins with more pin options such as alt function, pull, speed,
drive, interrupt mode, etc.
Note: this new `machine_pin_config()` function can replace
`machine_pin_set_mode()`, but the latter is left as-is to avoid breaking
anything.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
The rp2 port was enabling SSL and had finalizers enabled via the "extra
features" level, but missed explicitly enabling `MICROPY_PY_SSL_FINALISER`
(like esp32, stm32, and mimxrt did).
This commit makes `MICROPY_PY_SSL_FINALISER` default to enabled if
finalizers are enabled, and removes the explicit setting of this for
esp32, stm32, mimxrt (because they all use the "extra features" level).
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The only reason that const had to be disabled was to make the test output
match CPython when const was involved. Instead, this commit fixes the test
to handle the lines where const is used.
Also:
- remove the special handling for MICROPY_PERSISTENT_CODE_SAVE in
unix/mpconfigport.h, and make this automatic.
- move the check for MICROPY_PERSISTENT_CODE_SAVE to where it's used (like
we do for other similar checks) and add a comment explaining it.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This allows the cc3200 port to be build with the standard autobuild script
rather than the custom build-cc3200-latest.sh (which is now removed).
This also fixes the path inside the zip file (by using the `-j` flag to
zip).
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This should have been added in 4815af75bc
when the variants were combined. The original non-USB variant got this
implicitly, and therefore was not in mpconfigvariant.h
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
PICO might not always be a unique name across all ports, and the
convention generally for other boards is to do VENDOR_BOARD.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This merges the existing GENERIC, GENERIC_1M, and GENERIC_512k boards
into variants of the new ESP8266_GENERIC board (renamed from GENERIC so
as not to clash with other ports).
Also moves the generation of the "OTA" variant (previously generated by
autobuild/build-esp8266-latest.sh) into the variant.
Following the convention established for the WEACTSTUDIO rp2 board, the
names of the variants are FLASH_1M and FLASH_512K (but rename the .ld files
to use MiB and kiB).
Updates autobuild to build esp8266 firmware the same way as other ports.
This requires renaming the output from firmware-combined.bin to just
firmware.bin.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Board names need to be unique across ports, and GENERIC clashes with
the ESP8266 (which will be renamed to ESP8266_GENERIC).
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This allows switching between variants without clobbering the build
output.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This was used to override the firmware filename generated by the build
server (to match the historical name before board definitions existed).
Now we're making everything use the board definition name (i.e. the
directory name).
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This is to support a future change to add the variant name to the build
directory and therefore should be the same style as the board name.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This is to support a future change to add the variant name to the build
directory and therefore should be the same style as the board name.
This only affects the WEACTSTUDIO board. Also standardises on a convention
for naming flash-size variants. Normally we would write e.g. 2MiB, but in
uppercase, it's awkward to write 2MIB, so instead use 2M, 512K, etc for
variant names, but use 2MiB when not constrained by case (e.g. a regular
filename).
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This is to support a future change to add the variant name to the build
directory and therefore should be the same style as the board name.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
MICROPY_PY_STM_CONST defaults to 1 if MICROPY_PY_STM is set. Overriding to
0 disables the named register peripheral constants being including in the
stm32 module.
This saves about 7.5KB of code size for the STM32WL55, which is significant
as this SoC doesn't have a lot of flash.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This is the minimum C interface to allow a modem driver to be built in
Python. Interface is simple, with the intention that the micropython-lib
driver is the main (only) consumer of it.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
No IRQHandlers were compiled in for this board.
Includes small consolidation of the same DMAMUX_ENABLE line for STM32G4,
STM32WB, STM32WL.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
Switches default on the NUCLEO_WL55 board to use the HSE oscillator powered
from PB0_VDDTCXO pin.
Build-time configuration can select from MSI internal oscillator (previous
default), HSE via crystal, or HSE bypass with TCXO powered from PB0_VDDTCXO
pin (new default)
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This is a "normal" SPI peripheral with no external pins, to avoid having to
grow spi_obj[] for just this one board map it as SPI ID 3 (board has SPI
IDs 1,2 already).
Signed-off-by: Angus Gratton <angus@redyak.com.au>
At the Adafruit Metro M7 the pin GPIO_AD_13 is used for JTAG. Therefore
it is not configured for RTS at UART 2 and 3.
Signed-off-by: robert-hh <robert@hammelrath.com>
Looks like copy-paste from the stm32 make-pins.py, references a function
that is not present in the renesas-ra version.
Found by Ruff checking F821.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
subprocess.CalledProcessError() constructor arguments aren't documented,
but these are them. Even if they change, it's an improvement over a
non-existent exception name!
Found by Ruff checking F821.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
These files all use decorators (@asm_thumb, @asm_pio) that add names to the
function scope, that the linter cannot see.
It's useful to clear them in the file not in pyproject.toml as example code
will be copied and adapted elsewhere, and those developers may also use
Ruff (we hope!)
Signed-off-by: Angus Gratton <angus@redyak.com.au>
The call to machine_uart_deinit_all() is needed to avoid a crash after soft
reset, if a UART had been used and data arrives before it is instantiated
again.
Signed-off-by: robert-hh <robert@hammelrath.com>
