Commit Graph

187 Commits

Author SHA1 Message Date
robert-hh
2a4825848c mimxrt/usb: Change macro name MICROPY_HW_USB_STR_MANUF.
Change it into MICROPY_HW_USB_MANUFACTURER_STRING to be compatible with
other ports.
2022-11-17 08:27:33 +01:00
Patrick Joy
f44246c4c9 mimxrt/README: Add build and flashing instructions. 2022-11-17 14:21:59 +11:00
robert-hh
5e990cc27f mimxrt: Add support for MIMXRT1176 MCUs, and MIMXRT1170_EVK board.
The RT1176 has two cores, but the actual firmware supports only the CM7.
There are currently no good plans on how to use the CM4.

The actual MIMXRT1170_EVK board is on par with the existing MIMXRT boards,
with the following extensions:
- Use 64 MB RAM for the heap.
- Support both LAN interfaces as LAN(0) and LAN(1), with LAN(1)
  being the 1GB interface.

The dual LAN port interface can eventually be adapted as well for the
RT1062 MCU.

This work was done in collaboration with @alphaFred.
2022-11-17 14:11:50 +11:00
iabdalkader
71881116e6 extmod/extmod.mk: Set default mbedtls config file in extmod Makefile. 2022-11-09 18:43:13 +01:00
robert-hh
8afa6df23d mimxrt/modmachine: Move dht_readinto() to the machine module. 2022-11-09 15:56:43 +11:00
robert-hh
5d473d3093 mimxrt/mphalport: Add a timeout to mp_hal_stdout_tx_strn().
If USB CDC is connected and the board sends data, but the host does not
receive the data, the device locks up.  This is fixed in this commit by
having a timeout of 500ms, after which time the transmission is skipped.
2022-11-09 11:16:25 +11:00
Damien George
98cbace299 mimxrt/machine_timer: Use extmod version of machine.Timer.
Signed-off-by: Damien George <damien@micropython.org>
2022-10-27 14:43:03 +11:00
robert-hh
65fa7fd8bb mimxrt/machine_timer: Use soft-timer implementation for machine.Timer.
This releases the hardware timers for other tasks, which need a higher
resolution and faster response.  And it is less port-specific code.
2022-10-27 14:09:29 +11:00
robert-hh
9d2e179fa5 mimxrt: Fix CPU freeze when calling __WFE() in MICROPY_EVENT_POLL_HOOK.
This issue affected i.MX RT 1052, 1062 and 1064.  It seems to be addressed
by Errata ERR006223, which also mentions i.MX RT101x and 102x, but these
devices worked well even without the change.  As a side effect, the current
consumption at an idle REPL drops significantly with this fix.

Fixes issue #7235.
2022-10-27 14:06:12 +11:00
robert-hh
e20bb98392 mimxrt/machine_pin: Add the Pin.toggle() method.
For consistency with other ports, even if this method is undocumented at
the moment.
2022-10-27 14:05:33 +11:00
Damien George
8874a09119 extmod/mbedtls: Enable elliptic curve DH and DSA cryptography.
This is necessary to access sites that only support these protocols.

The rp2 port already has ECDH enabled, so this just adds ECDSA there.  The
other ports now gain both ECDH and ECDSA.  The code size increase is:

- rp2 (PICO_W): +2916 bytes flash, +24 bytes BSS
- stm32 (PYBD_SF6): +20480 bytes flash, +32 bytes data, +48 bytes BSS
- mimxrt (TEENSY41): +20708 bytes flash, +32 bytes data, +48 bytes BSS
- unix (standard x86-64): +39344 executable, +1744 bytes data, +96 BSS

This is obviously a large increase in code size.  But there doesn't seem to
be any other option because without elliptic curve cryptography devices are
partially cut off from the internet.  For use cases that require small
firmware size, they'll need to build custom firmware with a custom mbedtls
config.

Signed-off-by: Damien George <damien@micropython.org>
2022-10-22 19:08:21 +11:00
Damien George
b337678964 extmod/mbedtls: Add common configuration file, and use it in all ports.
This is a no-op change.

Signed-off-by: Damien George <damien@micropython.org>
2022-10-22 19:06:21 +11:00
Jim Mussared
43bcfb148b mimxrt/Makefile: Split up SRC_C variables.
This improves clarity a bit, but also ensures that only the required files
are added to SRC_QSTR.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-10-12 00:08:49 +11:00
Jim Mussared
d6d8722558 extmod: Make extmod.mk self-contained.
This makes it so that all a port needs to do is set the relevant variables
and "include extmod.mk" and doesn't need to worry about adding anything to
OBJ, CFLAGS, SRC_QSTR, etc.

Make all extmod variables (src, flags, etc) private to extmod.mk.

Also move common/shared, extmod-related fragments (e.g. wiznet, cyw43,
bluetooth) into extmod.mk.

Now that SRC_MOD, CFLAGS_MOD, CXXFLAGS_MOD are unused by both extmod.mk
(and user-C-modules in a previous commit), remove all uses of them from
port makefiles.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-10-11 23:31:49 +11:00
Jim Mussared
87011f6353 extmod/extmod.mk: Make extmod.mk handle GIT_SUBMODULES.
This applies to nimble, btstack, axtls, mbedtls, lwip.

Rather than having the ports individually manage GIT_SUBMODULES for these
components, make extmod.mk append them when the relevant feature is
enabled.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-10-11 23:29:09 +11:00
Jim Mussared
67d05ed02b ports: Make generated pin.c handling more consistent across ports.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-10-11 23:18:46 +11:00
Jim Mussared
17f2783e4a all: Use += rather than = everywhere for CFLAGS/LDFLAGS/LIBS.
This avoids a surprise where an = can cancel out an earlier +=.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-10-11 23:17:41 +11:00
Jim Mussared
94beeabd2e py/obj: Convert make_new into a mp_obj_type_t slot.
Instead of being an explicit field, it's now a slot like all the other
methods.

This is a marginal code size improvement because most types have a make_new
(100/138 on PYBV11), however it improves consistency in how types are
declared, removing the special case for make_new.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-09-19 19:06:15 +10:00
Jim Mussared
6da41b5900 py/obj: Merge getiter and iternext mp_obj_type_t slots.
The goal here is to remove a slot (making way to turn make_new into a slot)
as well as reduce code size by the ~40 references to mp_identity_getiter
and mp_stream_unbuffered_iter.

This introduces two new type flags:
- MP_TYPE_FLAG_ITER_IS_ITERNEXT: This means that the "iter" slot in the
  type is "iternext", and should use the identity getiter.
- MP_TYPE_FLAG_ITER_IS_CUSTOM: This means that the "iter" slot is a pointer
  to a mp_getiter_iternext_custom_t instance, which then defines both
  getiter and iternext.

And a third flag that is the OR of both, MP_TYPE_FLAG_ITER_IS_STREAM: This
means that the type should use the identity getiter, and
mp_stream_unbuffered_iter as iternext.

Finally, MP_TYPE_FLAG_ITER_IS_GETITER is defined as a no-op flag to give
the default case where "iter" is "getiter".

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-09-19 19:06:13 +10:00
Jim Mussared
9dce82776d all: Remove unnecessary locals_dict cast.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-09-19 19:06:01 +10:00
Jim Mussared
662b9761b3 all: Make all mp_obj_type_t defs use MP_DEFINE_CONST_OBJ_TYPE.
In preparation for upcoming rework of mp_obj_type_t layout.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-09-19 19:06:01 +10:00
robert-hh
6472348c1b mimxrt/machine_uart: Fix a bug in UART.write().
Causing an incomplete send if the data size was longer than the buffer
size.
2022-09-13 18:35:48 +10:00
robert-hh
443fbcf81c mimxrt/machine_uart: Set the UART ioctl write poll flag properly.
It was always set to True.  The change adds a check to the tx status flag
which is set when all data is transferred.
2022-09-13 18:35:48 +10:00
robert-hh
0f048a5a2a mimxrt/machine_spi: Allow a setting of -1 for cs in the constructor.
In that case, no Pin will be configured for the CS signal, even if it is
internally still generated.  That setting allows to use any pin for CS,
which then must be controlled by the Python script.

Also make the default cs=-1 to match other ports (software CS).
2022-09-13 18:35:48 +10:00
robert-hh
8e54225140 mimxrt: Format the firmware image to match the new teensy loader.
The new teensy loader keeps the file system under certain conditions:
- The file size is properly set in the file header.
- The header version is 4.3

These changes are implemented here, requiring a backport of
fsl_flexspi_nor_boot.c.  There is still a problem with the command line
version of the teensy loader, which fails on the first attempt.  At the
second attempt it works.  The GUI version of the teensy loader is fine.
2022-09-13 18:35:48 +10:00
robert-hh
65ce7d7ade mimxrt/machine_uart: Drop a few commented lines about TX ring buffer. 2022-09-13 18:35:48 +10:00
Jim Mussared
d84c6ef0e8 ports: Use micropython-lib version of drivers in manifests. 2022-09-08 11:27:05 +10:00
Jim Mussared
203dae41fb all: Update all manifest.py files to use new features.
Changes in this commit:
- Manifest include's now use the directory path where possible (no longer
  necessary to include the manifest.py file explicitly).
- Add manifest.py for all drivers and components that are referenced by
  port/board manifests.
- Replace all uses of freeze() with package()/module(), except for port and
  board modules.
- Use opt=3 everywhere, for consistency and to reduce code size.
- Use require() instead of include() for all micropython-lib references.
- Remove support for optional board-level manifest.py in mimxrt port, to
  make it behave the same as other ports (the board must set
  FROZEN_MANIFEST to a custom manifest.py, which can optionally include the
  default, port-level manifest).
- Also reinstates modules that were accidentally removed from the esp8266
  512k build in fbe9417b90.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Signed-off-by: Damien George <damien@micropython.org>
2022-09-05 18:43:18 +10:00
robert-hh
49e17c8bb0 mimxrt/machine_uart: Implement uart.flush() and uart.txdone().
uart.flush()

flush() will wait until all characters have been sent.To avoid a
permanent lock, a timeout applies depending on the size of txbuf
and the baud rate.

ret = uart.txdone()

ret is True if no transfer is in progress.
ret is False otherwise.
2022-08-31 00:18:21 +10:00
Jim Mussared
8a0ee5a5c0 py/objstr: Split mp_obj_str_from_vstr into bytes/str versions.
Previously the desired output type was specified.  Now make the type part
of the function name.  Because this function is used in a few places this
saves code size due to smaller call-site.

This makes `mp_obj_new_str_type_from_vstr` a private function of objstr.c
(which is almost the only place where the output type isn't a compile-time
constant).

This saves ~140 bytes on PYBV11.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-08-26 16:43:55 +10:00
Damien George
8f4c108025 all: Remove MICROPY_PY_IO_FILEIO config option.
Since commit e65d1e69e8 there is no longer an
io.FileIO class, so this option is no longer needed.

This option also controlled whether or not files supported being opened in
binary mode (eg 'rb'), and could, if disabled, lead to confusion as to why
opening a file in binary mode silently did the wrong thing (it would just
open in text mode if MICROPY_PY_IO_FILEIO was disabled).

The various VFS implementations (POSIX, FAT, LFS) were the only places
where enabling this option made a difference, and in almost all cases where
one of these filesystems were enabled, MICROPY_PY_IO_FILEIO was also
enabled.  So it makes sense to just unconditionally enable this feature
(ability to open a file in binary mode) in all cases, and so just remove
this config option altogether.  That makes configuration simpler and means
binary file support always exists (and opening a file in binary mode is
arguably more fundamental than opening in text mode, so if anything should
be configurable then it should be the ability to open in text mode).

Signed-off-by: Damien George <damien@micropython.org>
2022-08-18 11:54:17 +10:00
Jim Mussared
28aaab9590 py/objstr: Add hex/fromhex to bytes/memoryview/bytearray.
These were added in Python 3.5.

Enabled via MICROPY_PY_BUILTINS_BYTES_HEX, and enabled by default for all
ports that currently have ubinascii.

Rework ubinascii to use the implementation of these methods.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-08-12 12:44:30 +10:00
Jim Mussared
be83c08f46 ports: Always append to GIT_SUBMODULES.
Avoids overwriting submodules required by base makefiles.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-08-03 00:05:26 +10:00
Angus Gratton
fdfe4eca74 ports: Always include debug information in the ELF.
For bare metal ARM & xtensa targets, passing -g will make the ELF file
larger but doesn't change the binary size.  However, this means tools like
gdb, addr2line, etc can extract source-level information from the ELF.

Also standardise -ggdb to -g, these produce the exact same ELF file on
arm-none-eabi-gcc and will use DWARF format for all these ports.
2022-07-29 11:24:00 +10:00
Jim Mussared
092784da19 ports: Remove unused mp_type_{fileio/textio} macros in mpconfigport.h.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-07-26 18:07:22 +10:00
Tim Gates
f736afb577 drivers,ports: Fix a few typos in comments.
Fixes:
- Should read `definitions` rather than `defintions`.
- Should read `resolution` rather than `resoultion`.
- Should read `inefficient` rather than `inefficent`.
- Should read `closed` rather than `closded`.

Signed-off-by: Tim Gates <tim.gates@iress.com>
2022-07-23 23:24:24 +10:00
robert-hh
80339f1a33 ports: Adapt mimxrt, nrf and rp2 ports to work with latest TinyUSB.
rp2: change tud_task() to tud_task_ext().

mimxrt: use lib/tinyusb/src/portable/chipidea/ci_hs/dcd_ci_hs.c instead of
lib/tinyusb/src/portable/nxp/transdimension/dcd_transdimension.c.

nrf: add a definition for the changed tud_task().  tud_task() is changed
to tud_task_ext(), and the #define for backward compatibility is in
src/device/usbd.h.

The items I know which are fixed with this version:
- Fix for the SAMD USB lock-up.
- Support the MIMXRT11XX series of MCUs.
- Fix a wrong pin definition for MIMXRT1050_EVKB.

Tested with the MIMXRT boards, rp2 Pico, SAMD boards, nrf board.
2022-07-19 11:27:21 +10:00
Damien George
b89422ceaa extmod: Always use custom mbedtls error message code.
All ports that use mbedtls use the custom error messages in
mp_mbedtls_errors.c.  This commit simplifies the build so that ports don't
need to explicitly add this file, it's now used by default when mbedtls is
enabled.

Signed-off-by: Damien George <damien@micropython.org>
2022-07-18 22:55:22 +10:00
David Lechner
7e4b205cb0 py/mpstate: Drop MICROPY_PORT_ROOT_POINTERS from mp_state_vm_t.
All in-tree uses of MICROPY_PORT_ROOT_POINTERS have been replaced with
MP_REGISTER_ROOT_POINTER(), so now we can remove both
MICROPY_PORT_ROOT_POINTERS and MICROPY_BOARD_ROOT_POINTERS from the code
and remaining config files.

Signed-off-by: David Lechner <david@pybricks.com>
2022-07-18 13:51:16 +10:00
David Lechner
a316a8fdb3 mimxrt: Use MP_REGISTER_ROOT_POINTER().
This uses MP_REGISTER_ROOT_POINTER() to register all port-specific root
pointers in the mimxrt port.

Signed-off-by: David Lechner <david@pybricks.com>
2022-07-18 13:50:34 +10:00
David Lechner
a3703584fe extmod/modnetwork: Use MP_REGISTER_ROOT_POINTER().
This uses MP_REGISTER_ROOT_POINTER() to register mod_network_nic_list and
removes the same from all mpconfigport.h.

Signed-off-by: David Lechner <david@pybricks.com>
2022-07-18 13:50:25 +10:00
David Lechner
81dbea1ce3 shared/readline: Use MP_REGISTER_ROOT_POINTER().
This uses MP_REGISTER_ROOT_POINTER() to register the readline_history root
pointer array used by shared/readline.c and removes the registration from
all mpconfigport.h files.

This also required adding a new MICROPY_READLINE_HISTORY_SIZE config option
since not all ports used the same sized array.

Signed-off-by: David Lechner <david@pybricks.com>
2022-07-18 13:48:49 +10:00
Philipp Ebensberger
4ce1adab31 mimxrt/boards: Remove conditional assignment of flash type/size.
Removes conditional assignment because respective variables should only be
set in board makefile fragments.  Hence no conditional assignment needed.
2022-06-24 17:58:27 +10:00
Philipp Ebensberger
434974ec77 mimxrt/Makefile: Fix some minor formatting inconsistencies. 2022-06-24 17:58:27 +10:00
Philipp Ebensberger
c957c76f4d mimxrt/Makefile: Rework floating point config.
Reworks source file and compile flags selection for floating point support.
2022-06-24 17:58:27 +10:00
Philipp Ebensberger
bec0524dbf mimxrt/Makefile: Rework board flash type handling.
Reworks handling and configuration of different board flash types in the
Makefile, linker scripts and board makefile fragments.
2022-06-24 17:58:27 +10:00
Philipp Ebensberger
84339aa8ec mimxrt/Makefile: Modify handling of SDCARD option.
Removes separate `if` case in Makefile for setting SDCARD option define.
2022-06-24 17:58:27 +10:00
Philipp Ebensberger
b1aec393b1 mimxrt/Makefile: Modify handling of SDRAM option.
Replaces preprocessor macro for SDRAM option from #ifdef to #if in order to
allow always setting the define `MICROPY_HW_SDRAM_AVAIL` just with the
appropriate value 0/1.  This eliminates one `if` in the Makefile.
2022-06-24 17:58:27 +10:00
Philipp Ebensberger
fbc50196ad mimxrt/Makefile: Refactor Makefile and divide it into sections.
Reworks grouping of Makefile variables and reorders variable values in
alphabetic order.
2022-06-24 17:58:25 +10:00
David Lechner
c118b5d0e4 extmod/extmod.mk: Separate out extmod file list from py.mk to extmod.mk.
This separates extmod source files from `py.mk`.  Previously, `py.mk`
assumed that every consumer of the py/ directory also wanted to include
extmod/.  However, this is not the case.  For example, building mpy-cross
uses py/ but doesn't need extmod/.

This commit moves all extmod-specific items from `py.mk` to `extmod.mk` and
explicitly includes `extmod.mk` in ports that use it.

Signed-off-by: David Lechner <david@pybricks.com>
2022-06-21 00:14:34 +10:00