Commit Graph

24 Commits

Author SHA1 Message Date
Damien George
61339aa506 stm32: Add initial support for H5 MCUs.
This commit adds initial support for STM32H5xx MCUs.  The following
features have been confirmed to be working on an STM32H573:
- UART over REPL and USB CDC
- USB CDC and MSC
- internal flash filesystem
- machine.Pin
- machine.SPI transfers with DMA
- machine.ADC
- machine.RTC
- pyb.LED
- pyb.Switch
- pyb.rng
- mboot

Signed-off-by: Damien George <damien@micropython.org>
2023-06-15 11:09:20 +10:00
Damien George
f7f8332ddf stm32/machine_adc: Handle ADC resolution less than 8 bits on all MCUs.
All MCUs can have 6-bit resolution; see adc_cr_to_bits_table.

Signed-off-by: Damien George <damien@micropython.org>
2023-06-15 11:02:55 +10:00
Damien George
13fcd8440e stm32: Add support for STM32H723 MCUs.
Signed-off-by: Damien George <damien@micropython.org>
2023-03-21 14:02:49 +11:00
yn386
427d72667f stm32: Add support for STM32L1 MCUs.
This change adds STM32L1 support to the STM32 port.
2022-09-25 23:56:41 +10:00
Jim Mussared
94beeabd2e py/obj: Convert make_new into a mp_obj_type_t slot.
Instead of being an explicit field, it's now a slot like all the other
methods.

This is a marginal code size improvement because most types have a make_new
(100/138 on PYBV11), however it improves consistency in how types are
declared, removing the special case for make_new.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-09-19 19:06:15 +10:00
Jim Mussared
9dce82776d all: Remove unnecessary locals_dict cast.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-09-19 19:06:01 +10:00
Jim Mussared
662b9761b3 all: Make all mp_obj_type_t defs use MP_DEFINE_CONST_OBJ_TYPE.
In preparation for upcoming rework of mp_obj_type_t layout.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-09-19 19:06:01 +10:00
Jim Mussared
0e7bfc88c6 all: Use mp_obj_malloc everywhere it's applicable.
This replaces occurences of

    foo_t *foo = m_new_obj(foo_t);
    foo->base.type = &foo_type;

with

    foo_t *foo = mp_obj_malloc(foo_t, &foo_type);

Excludes any places where base is a sub-field or when new0/memset is used.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2022-05-03 22:28:14 +10:00
Asensio Lorenzo Sempere
010012c7c3 stm32: Add support for G0 MCUs.
This commit adds support for the STM32G0 series of MCUs.

Signed-off-by: Asensio Lorenzo Sempere <asensio.aerospace@gmail.com>
2022-04-28 11:56:15 +10:00
Damien George
e0a0719416 stm32: Add initial support for STM32WL MCUs.
Signed-off-by: Damien George <damien@micropython.org>
2022-02-04 09:43:43 +11:00
Herwin Grobben
8f68e26f79 stm32: Add support for G4 MCUs, and add NUCLEO_G474RE board defn.
This commit adds support for the STM32G4 series of MCUs, and a board
definition for NUCLEO_G474RE.  This board has the REPL on LPUART1 which is
connected to the on-board ST-link USB-UART.
2022-02-01 16:21:01 +11:00
Damien George
88ac5a3116 stm32: Update L4 code to build with latest stm32lib and L4 HAL 1.17.0.
Signed-off-by: Damien George <damien@micropython.org>
2021-12-14 10:48:01 +11:00
Jan Staal
9e2423e730 stm32: Add support for H7A3(Q)/H7B3(Q), and STM32H73B3I_DK board defn.
This commit is based upon prior work of @dpgeorge and @koendv.

MCU support for the STM32H7A3 and B3 families MCUs:
- STM32H7A3xx
- STM32H7A3xxQ (SMPS)
- STM32H7B3xx
- STM32H7B3xxQ (SMPS)

Support has been added for the STM32H7B3I_DK board.

Signed-off-by: Jan Staal <info@janstaal.com>
2021-09-16 12:29:28 +10:00
Damien George
fd01b6c779 stm32/adc: Allow mboot to use basic ADC functions.
Signed-off-by: Damien George <damien@micropython.org>
2021-04-30 00:42:59 +10:00
Damien George
80883a82c0 stm32/adc: Deselect VBAT after reading to prevent battery drain.
Signed-off-by: Damien George <damien@micropython.org>
2020-12-18 13:32:02 +11:00
Damien George
0118c07916 stm32/machine_adc: Fix ADC auto-calibration to run when ADC not enabled.
Prior to this commit, the ADC calibration code was never executing because
ADVREGEN bit was set making the CR register always non-zero.

This commit changes the logic so that ADC calibration is always run when
the ADC is disabled and an ADC channel is initialised.  It also uses the LL
API functions to do the calibration, to make sure it is done correctly on
each MCU variant.

Signed-off-by: Damien George <damien@micropython.org>
2020-10-29 11:09:43 +11:00
Damien George
0f7b5cceea stm32/machine_adc: Make setting of ADC1_COMMON->CCR clearer on STM32WB. 2020-06-02 10:48:49 +10:00
Jim Mussared
def76fe4d9 all: Use MP_ERROR_TEXT for all error messages. 2020-04-05 15:02:06 +10:00
Damien George
69661f3343 all: Reformat C and Python source code with tools/codeformat.py.
This is run with uncrustify 0.70.1, and black 19.10b0.
2020-02-28 10:33:03 +11:00
Damien George
ad7213d3c3 py: Add mp_raise_msg_varg helper and use it where appropriate.
This commit adds mp_raise_msg_varg(type, fmt, ...) as a helper for
nlr_raise(mp_obj_new_exception_msg_varg(type, fmt, ...)).  It makes the
C-level API for raising exceptions more consistent, and reduces code size
on most ports:

   bare-arm:   +28 +0.042%
minimal x86:  +100 +0.067%
   unix x64:   -56 -0.011%
unix nanbox:  -300 -0.068%
      stm32:  -204 -0.054% PYBV10
     cc3200:    +0 +0.000%
    esp8266:   -64 -0.010% GENERIC
      esp32:  -104 -0.007% GENERIC
        nrf:  -136 -0.094% pca10040
       samd:    +0 +0.000% ADAFRUIT_ITSYBITSY_M4_EXPRESS
2020-02-13 11:52:40 +11:00
Chris Mason
0096041c99 stm32/{adc,machine_adc}: Change ADC clock and sampling time for F0 MCUs.
STM32F0 has PCLK=48MHz and maximum ADC clock is 14MHz so use PCLK/4=12MHz
to stay within spec of the ADC peripheral.  In pyb.ADC set common sampling
time to approx 4uS for internal and external sources.  In machine.ADC
reduce sample time to approx 1uS for external source, leave internal at
maximum sampling time.
2019-10-04 21:39:17 +10:00
Damien George
22099ab88f stm32/machine_adc: Fix build for F4 and L4 MCUs that only have ADC1. 2019-09-12 19:10:12 +10:00
Damien George
62fe013a5f stm32/machine_adc: Improve operation of ADC for H7, L4 and WB MCUs. 2019-09-06 17:55:12 +10:00
Damien George
ebacdfabb6 stm32/machine_adc: Add machine.ADC class. 2019-09-04 15:40:24 +10:00