Commit Graph

14748 Commits

Author SHA1 Message Date
robert-hh
267d1ab2ba samd/mpconfigport: Drop support for SoftSPI max speed.
Saves ~140 bytes and is not really needed, since for higher baud rates hard
SPI is available.

Signed-off-by: robert-hh <robert@hammelrath.com>
2023-05-22 18:35:45 +10:00
Damien George
2771b20d29 tools/mpremote: Add repl option to escape non-printable characters.
This commit adds the "--escape-non-printable" option to the repl command.
When specified the REPL console will escape non-printable characters,
printing them as their hex value in square brackets.

This escaping behaviour was previously the default and only behaviour, but
it is now opt-in.

As part of this change, the speed of echoing device data to the console is
improved by by reading and writing in chunks.

Signed-off-by: Damien George <damien@micropython.org>
2023-05-22 14:13:24 +10:00
patrick
a802f71908 esp32/uart: Use xtal as UART clock source on S3 and C3.
Change UART clock source on S3/C3 so the UART can operate when CPU
frequency is below 80MHz.  This allows the UART to remain operational when
using Dynamic Frequency Scaling (DFS).

Signed-off-by: Patrick Joy <patrick@joytech.com.au>
2023-05-22 10:11:24 +10:00
patrick
05e143dbdd esp32/esp32_ulp: Enable FSM ULP for S2 and S3 chips.
This commit enables the ULP for the S2 and S3 chips.

Note this is the FSM (Finite State Machine) ULP.

Signed-off-by: Patrick Joy <patrick@joytech.com.au>
2023-05-19 22:37:25 +10:00
UnexpectedMaker
3a7ad64267 esp32/boards: Add some missing board configs for two UM boards. 2023-05-19 22:30:42 +10:00
iabdalkader
bfcaf39197 stm32/irq: Fix typo in comment about priorities.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
2023-05-19 22:23:33 +10:00
iabdalkader
70b60fe24e renesas-ra/irq: Fix typo in comment about IRQ priorities.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
2023-05-19 22:23:10 +10:00
Andrew Leech
f03ac04321 stm32/mboot: Fix alignment of packed final buffer.
Once all the firmware has been flashed and the final signatures checked,
mboot writes the "all good" byte into the header of the application.  This
step uses the buffer firmware_head which, if unaligned in the build, fails
when cast to a uint64_t* in flash.c.

Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au>
2023-05-19 22:16:53 +10:00
brave ulysses
ad216be5f1 stm32/boards/stm32h723_af.csv: Fix ADC AF definitions.
These were incorrectly added in d995c01042.
The fix here includes the full differential ADC definitions.

Signed-off-by: brave ulysses <brave_ulysses@email.com>
2023-05-19 22:12:05 +10:00
Chris Wilson
1ecc54888f extmod/extmod.mk: Suppress deprecated-non-prototype warning.
Signed-off-by: Chris Wilson <chris@cgnd.dev>
2023-05-19 22:03:17 +10:00
Mingjie Shen
a9fc0343f0 extmod/vfs_lfsx: Fix offset used before range check.
Use of offset 'from' should follow the range check.

Signed-off-by: Mingjie Shen <shen497@purdue.edu>
2023-05-19 22:01:10 +10:00
David Lechner
978829fcd6 shared/upytesthelper: Fix spelling of "default".
Signed-off-by: David Lechner <david@pybricks.com>
2023-05-19 21:58:32 +10:00
Jim Mussared
46d070bfee tools/manifestfile.py: Fix license capturing.
The license field was incorrectly being set to the version.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2023-05-19 21:56:38 +10:00
marble
b5c81f6bfb docs/develop/porting: Add missing code to example main.c and Makefile.
These two missing lines caused the build process to fail when implementing
the tutorial example port.

Signed-off-by: marble <git@computer-in.love>
2023-05-19 21:51:19 +10:00
glenn20
12dbbc8065 docs/library/espnow: Update espnow docs for WLAN.config(pm=x) options.
Update docs/library/espnow.rst to add:
- guidance on using WLAN.config(pm=WLAN.PM_NONE) for reliable
  espnow performance while also connected to a wifi access point;
- guidance on receiving encrypted messages;
- correction for default value of "encrypt" parameter (add_peer());
- guidance on use of ESPNow.irq(): recommand users readout all messages
  in the buffer each time the callback is called.

Signed-off-by: Glenn Moloney <glenn.moloney@gmail.com>
2023-05-19 21:48:08 +10:00
Damien George
ea7031faff py/runtime: If inplace binop fails then try corresponding normal binop.
The code that handles inplace-operator to normal-binary-operator fallback
is moved in this commit from py/objtype.c to py/runtime.c, making it apply
to all types, not just user classes.

Signed-off-by: Damien George <damien@micropython.org>
2023-05-19 13:44:00 +10:00
Damien George
4b57330465 py/objstr: Return unsupported binop instead of raising TypeError.
So that user types can implement reverse operators and have them work with
str on the left-hand-side, eg `"a" + UserType()`.

Signed-off-by: Damien George <damien@micropython.org>
2023-05-19 13:42:35 +10:00
Damien George
ca9068e0ef py/objarray: Disallow memoryview addition.
Following CPython.  This is important for subsequent commits to work
correctly.

Signed-off-by: Damien George <damien@micropython.org>
2023-05-19 13:33:54 +10:00
Damien George
9accb7dd44 tests/basics: Add more tests for hashing of various types.
Signed-off-by: Damien George <damien@micropython.org>
2023-05-19 12:35:12 +10:00
David Lechner
2fe6d4eb86 py/objdict: Fix __hash__ for dict_view types.
This adds a unary_op implementation for the dict_view type that makes
the implementation of `hash()` for these types compatible with CPython.

Signed-off-by: David Lechner <david@pybricks.com>
2023-05-19 12:06:17 +10:00
David Lechner
8491eb190f py/objslice: Ensure slice is not hashable.
As per https://bugs.python.org/issue408326, the slice object should not be
hashable.  Since MicroPython has an implicit fallback when the unary_op
slot is empty, we need to fill this slot.

Signed-off-by: David Lechner <david@pybricks.com>
2023-05-19 12:06:06 +10:00
David Lechner
eaccaa3677 py/obj: Remove mp_generic_unary_op().
Since converting to variable sized slots in mp_obj_type_t, we can now
reduce the code size a bit by removing mp_generic_unary_op() and the
corresponding slots where it is used. Instead we just implement the
generic `__hash__` operation in the runtime.

Signed-off-by: David Lechner <david@pybricks.com>
2023-05-19 12:04:44 +10:00
Damien George
53cb073571 esp32,esp8266: Change network.WLAN from a function to a type.
When the network module was first introduced in the esp8266 port in
ee3fec3167 there was only one interface (STA)
and, to save flash, the WLAN object was aliased to the network module,
which had just static methods for WLAN operations.  This was subsequently
changed in 9e8396accb when the AP interface
was introduced, and the WLAN object became a true class.

But, network.WLAN remained a function that returned either the STA or AP
object and was never upgraded to the type itself.  This scheme was then
copied over to the esp32 port when it was first introduced.

This commit changes network.WLAN from a function to a reference to the WLAN
type.  This makes it consistent with other ports and network objects, and
allows accessing constants of network.WLAN without creating an instance.

Signed-off-by: Damien George <damien@micropython.org>
2023-05-18 14:52:28 +10:00
Jim Mussared
17127bbee5 tests/run-tests.py: Ensure correct cwd for mpy tests.
Previously when using --via-mpy, the file was compiled to tests/<tmp>.mpy
and then run using `micropython -m <tmp>` in the current cwd
(usually tests/).  This meant that an import in the test would be resolved
relative to tests/.

This is different to regular (non-via-mpy) tests, where we run (for
example) `micropython basics/test.py` which means that an import would be
resolved relative to basics/.

Now --via-mpy matches the .py behavior.  This is important because:
a) It makes it so import tests do the right thing.
b) There are directory names in tests/ that match built-in module names.

Furthermore, it always ensures the cwd (for both micropython and cpython)
is the test directory (e.g. basics/) rather than being left unset.  This
also makes it clearer inside the test that e.g. file access is relative to
the Python file.

Updated tests with file paths to match.

This work was funded through GitHub Sponsors.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2023-05-18 13:48:21 +10:00
Damien George
ab3f9ecb59 github/workflows: Force use of Ubuntu-20.04 for unix 32-bit builds.
To be able to install libffi-dev:i386.

Signed-off-by: Damien George <damien@micropython.org>
2023-05-18 13:12:40 +10:00
Ondrej Wisniewski
29401a719f rp2/mphalport: Only use CYW43 MAC for WLAN0 interface.
Building the Pico-W needs the MICROPY_PY_NETWORK_CYW43 flag to be set in
order to include building the CYW43 Wifi driver.  But then mp_hal_get_mac()
handles the MAC assignment for all nics the "CYW43 way", copying the real
MAC provided by the WiFi hardware.  This will fail for all other NIC types,
resulting in an invalid MAC address.

The solution in this commit is to add a check for the NIC type parameter
idx and handle the MAC address respectively.
2023-05-18 13:06:06 +10:00
Phil Howard
4ce360fa83 rp2/CMakeLists: Allow relative MICROPY_BOARD_DIR when invoking cmake.
Convert to an absolute path to always reliably locate manifest.py.  This is
already done in Makefile, but is also needed in CMakeLists.txt if cmake is
invoked directly.

Signed-off-by: Phil Howard <phil@pimoroni.com>
2023-05-18 12:51:36 +10:00
Adam Green
f9958417d8 rp2: Make rp2_state_machine_exec accept integers.
Currently rp2.StateMachine.exec(instr_in) requires that the instr_in
parameter be a string representing the PIO assembly language instruction
to be encoded by rp2.asm_pio_encode(). This commit allows the parameter
to also be of integral type. This is useful if the exec() method is
being called often where the use of pre-encoded machine code is
desireable.

This commit still supports calls like:
    sm.exec("set(0, 1)")

It also now supports calls like:
    # Performed once earlier, maybe in __init__()
    assembled_instr = rp2.asm_pio_encode("out(y, 8)", 0)
    # Performed multiple times later as the PIO state machine is
    # configured for its next run.
    sm.exec(assembled_instr)

The existing examples/rp2/pio_exec.py and examples/rp2/pio_pwm.py that
exercise the rp2.StateMachine.exec() method still work with this change.

Signed-off-by: Adam Green <adamgrym@yahoo.com>
2023-05-18 12:33:02 +10:00
Takeo Takahashi
3229791b60 renesas-ra: Add a macro definition to avoid compile error of FSP v4.4.0.
FSP v4.4.0 refers to CMSIS V5.4.1, and __COMPILER_BARRIER() is used in bsp.
On the other hand, lib/cmsis is V5.1.0 and the macro is not defined.
Therefore, compile error happens.
As the workaround, the macro definition is added.
If lib/cmsis is updated in the future, this addition can be removed.

Signed-off-by: Takeo Takahashi <takeo.takahashi.xv@renesas.com>
2023-05-11 16:18:39 +10:00
Takeo Takahashi
b4834e5cba renesas-ra: Update boards and ra directory files to support FSP v4.4.0.
* Update boards and ra files
* Remove unreferenced files, board_init.c and board_leds.c, from Makefile
* Remove unreferenced FSP instances from ra_gen/*.[ch]
* Remove unreferenced FSP config files ra_cfg/*.h
* e2 studio generates FSP instances but renesas-ra uses only followings:
  lpm, flash, ioport

Signed-off-by: Takeo Takahashi <takeo.takahashi.xv@renesas.com>
2023-05-11 16:18:39 +10:00
Takeo Takahashi
0c58e29074 lib/fsp: Update FSP for renesas-ra to the latest version v4.4.0.
Signed-off-by: Takeo Takahashi <takeo.takahashi.xv@renesas.com>
2023-05-11 16:18:39 +10:00
David Lechner
6a4a9bc147 windows/Makefile: Allow variants to add QSTR_DEFS.
This modifies the windows port Makefile to use += for QSTR_DEFS and
QSTR_GLOBAL_DEPENDENCIES so that variants can add additional files if
needed (similar to stm32 port).

Signed-off-by: David Lechner <david@pybricks.com>
2023-05-11 14:34:15 +10:00
David Lechner
6836acf3dc unix/Makefile: Allow variants to add QSTR_DEFS.
This modifies the unix port Makefile to use += for QSTR_DEFS and
QSTR_GLOBAL_DEPENDENCIES so that variants can add additional files if
needed (similar to stm32 port).

Signed-off-by: David Lechner <david@pybricks.com>
2023-05-11 14:34:01 +10:00
David Lechner
3e64d76122 docs/reference/mpyfiles: Add release info on v6.1.
This documents when MPY v6.1 was released.

Also add some clarification on how the version is encoded in the header.

Signed-off-by: David Lechner <david@pybricks.com>
2023-05-11 14:30:34 +10:00
Christian Clauss
4e4bdbd191 top: Add ruff to pre-commit.
This does not align with the other pre-commit jobs with are local custom
code but it should run accurately and quickly.

Signed-off-by: Christian Clauss <cclauss@me.com>
2023-05-10 09:57:26 +10:00
Christian Clauss
a000c61d5d tools/pyboard.py: Import errno to fix undefined name in PyboardError.
This will keep line 96 from raising a NameError.

Signed-off-by: Christian Clauss <cclauss@me.com>
2023-05-09 18:49:23 +10:00
robert-hh
65d376b11d mimxrt/machine_pin: Perform full configuration in machine_pin_set_mode.
machine_pin_set_mode() is used by the internal mp_hal_pin_xxx() set of
functions to configure pins.
2023-05-09 16:15:05 +10:00
robert-hh
14b862f70f mimxrt/machine_spi: Ignore transfers with len=0.
It was treated as an error before.  The error surfaced when using the
NINAW10 drivers for WiFi support.  Even if this is a bad behavior of the
NINA driver, machine_spi can be forgiving in that situation.
2023-05-09 16:14:40 +10:00
robert-hh
d2a02dcee3 mimxrt: Add missing UART defintion and remove obsolete config.
Changes in this commit:
- Add a missing UART defintion for MIMXRT1010_EVK.
- Remove an obsolete line from mpconfigport.h.
2023-05-09 16:13:51 +10:00
robert-hh
facc51f3ea mimxrt/mpconfigport: Add back lost uos.urandom().
It got lost in a clean-up session recently.
2023-05-09 16:13:27 +10:00
Philipp Ebensberger
a3f3b9045c mimxrt/flash: Separate low level driver code from flash object.
Separate low level flash access from mimxrt flash driver object.  Allows
better abstraction from hardware for testing and reuse in other areas (e.g.
bootloader).

Signed-off-by: Philipp Ebensberger <philipp.ebensberger@3bricks-software.de>
2023-05-09 15:18:36 +10:00
Jim Lipsey
7333c06d05 stm32/boards/ARDUINO_PORTENTA_H7: Enable FDCAN.
Add pin definitions to enable FDCAN support using the pyb.CAN() class.
2023-05-09 13:25:03 +10:00
David Lechner
468ed218c9 py/gc: Make improvements to MICROPY_GC_HOOK_LOOP.
Changes in this commit:
- Add MICROPY_GC_HOOK_LOOP to gc_info() and gc_alloc().  Both of these can
  be long running (many milliseconds) which is too long to be blocking in
  some applications.
- Pass loop variable to MICROPY_GC_HOOK_LOOP(i) macro so that implementers
  can use it, e.g. to improve performance by only calling a function every
  X number of iterations.
- Drop outer call to MICROPY_GC_HOOK_LOOP in gc_mark_subtree().
2023-05-09 12:44:14 +10:00
Damien George
7c645b52e3 CODECONVENTIONS: Require that commits be signed-off by the author.
And use "must" instead of "should" where appropriate in related text.

Signed-off-by: Damien George <damien@micropython.org>
2023-05-08 12:20:56 +10:00
Damien George
a31e3de400 extmod/network_cyw43: Add power management constants.
And allow querying the current power management mode.

Signed-off-by: Damien George <damien@micropython.org>
2023-05-08 11:56:31 +10:00
glenn20
1093dea709 esp32,esp8266: Add support to set/get power saving mode of WLAN.
For esp32 and esp8266 this commit adds:
- a 'pm' option to WLAN.config() to set/get the wifi power saving mode; and
- PM_NONE, PM_PERFORMANCE and PM_POWERSAVE constants to the WLAN class.

This API should be general enough to use with all WLAN drivers.

Documentation is also added.
2023-05-06 13:51:00 +10:00
robert-hh
786013d467 docs/samd: Make use of pin names more consistent in examples.
This keeps up with the changed Pin naming scheme.
2023-05-04 13:19:19 +10:00
Damien George
38243cd8e0 extmod/machine_pwm: Remove PWM_INIT and PWM_DUTY_U16_NS config options.
All ports that enable MICROPY_PY_MACHINE_PWM now enable these two
sub-options, so remove these sub-options altogether to force consistency in
new ports that implement machine.PWM.

Signed-off-by: Damien George <damien@micropython.org>
2023-05-04 13:19:19 +10:00
robert-hh
7952694a3c rp2/machine_pwm: Add duty_x() checks and return 0 if PWM is not started.
Changes in this commit:
- Limit duty_u16() to 65535 and duty_ns() to the period duration.
- Return 0 for pwm.freq() if the frequency has not been set yet.
- Return 0 for pwm.duty_us16() and duty_ns() unless both frequency and
  duty cycle have been set.
- Initialize the pin to PWM at the very end of the constructor, to avoid
  possible glitches on the pin when setting up the PWM.
2023-05-04 13:18:58 +10:00
robert-hh
0b3b508d1d rp2/machine_pwm: Add support for inverting a PWM channel output.
Using the invert=True|False keyword option with the constructor or init().
2023-05-04 13:18:47 +10:00