Commit Graph

12 Commits

Author SHA1 Message Date
Mike Causer
47b778332a all: Replace busses with buses.
"buses" is the widely accepted plural form of "bus".
2021-05-20 23:22:03 +10:00
aziubin
7546d3cf73 stm32/boards/NUCLEO_L476RG: Add 5 remaining UARTs.
STM32L476RG MCU of NUCLEO_L476RG board has 6 UART/USART units in total
(USART1, USART2, USART3, UART4, UART5 and LPUART1), but only UART2,
connected to REPL, was defined and available in Python code.
Defined are all 5 remaining UART/USART units including LPUART1.

Signed-off-by: Alexander Ziubin aziubin@googlemail.com
2021-04-09 15:00:55 +10:00
Damien George
26e90a0514 stm32/boards: Enable MICROPY_HW_RTC_USE_LSE on L4 boards.
The previous commit changed the default configuration on L4 MCUs to use
LSI, so configure these boards to use LSE again.
2019-10-04 16:10:13 +10:00
Chris Mason
3786592097 stm32/boards: Optimise flash and RAM allocation for L4 boards.
Optimisations are:
- Remove FLASH_ISR section since devices with a small flash sector erase
  size don't need special FLASH_ISR handling.  This reduces flash image by
  approx 1.5k.
- Make SRAM2 contiguous with SRAM1 where possible.
- Simplify configuration of 2k RAM buffer used for flash filesystem.

RAM changes with this commit:
- L432: stack   6k -> 10k,  bss + heap   42k ->  52k
- L476: stack  16k -> 30k,  bss + heap   80k ->  96k
- L496: stack 206k -> 16k,  bss + heap  112k -> 302k
2019-07-01 16:57:20 +10:00
Damien George
009b1f6559 stm32/boards: Rework all stm32??xx_hal_conf.h files to use common code.
This eliminates a lot of duplicated code in these header files.
2019-06-25 14:18:24 +10:00
Jolatomme
d1acca3c71 stm32/boards/NUCLEO_L476RG: Add support for RNG, DAC and CAN1.
PLLQ is changed to get CAN working, and I2C1 pins are changed to those
prescribed by the board.
2019-02-14 00:28:28 +11:00
Damien George
ed75b2655f stm32/Makefile: Allow a board to config either 1 or 2 firmware sections.
This patch forces a board to explicitly define TEXT1_ADDR in order to
split the firmware into two separate pieces.  Otherwise the default is now
to produce only a single continuous firmware image with all ISR, text and
data together.
2018-03-27 21:24:15 +11:00
Damien George
95b2cb008e stm32/Makefile: Rename FLASH_ADDR/TEXT_ADDR to TEXT0_ADDR/TEXT1_ADDR.
To make it clearer that these addresses are both for firmware text and that
they have a prescribed ordering.
2018-03-27 21:20:04 +11:00
Damien George
7aec06ca9a stm32/boards: Allow boards to have finer control over the linker script.
This patch allows a particular board to independently specify the linker
scripts for 1) the MCU memory layout; 2) how the different firmware
sections are arranged in memory.  Right now all boards follow the same
layout with two separate firmware section, one for the ISR and one for the
text and data.  This leaves room for storage (filesystem data) to live
between the firmware sections.

The idea with this patch is to accommodate boards that don't have internal
flash storage and only need to have one continuous firmware section.  Thus
the common.ld script is renamed to common_ifs.ld to make explicit that it
is used for cases where the board has internal flash storage.
2018-03-27 21:17:48 +11:00
Damien George
34911f1a57 stm32/boards: Update all boards to work with new USB configuration. 2018-02-13 18:57:01 +11:00
Damien George
02f88cb2df stm32/boards: Remove all config options that are set to defaults.
mpconfigboard_common.h now sets the defaults so there is no longer a need
to explicitly list all configuration options in a board's mpconfigboard.h
file.
2018-02-09 18:40:40 +11:00
Damien George
01dd7804b8 ports: Make new ports/ sub-directory and move all ports there.
This is to keep the top-level directory clean, to make it clear what is
core and what is a port, and to allow the repository to grow with new ports
in a sustainable way.
2017-09-06 13:40:51 +10:00