micropython/ports/stm32/irq.h

153 lines
5.7 KiB
C
Raw Normal View History

/*
* This file is part of the MicroPython project, http://micropython.org/
*
* The MIT License (MIT)
*
* Copyright (c) 2013, 2014 Damien P. George
*
* Permission is hereby granted, free of charge, to any person obtaining a copy
* of this software and associated documentation files (the "Software"), to deal
* in the Software without restriction, including without limitation the rights
* to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
* copies of the Software, and to permit persons to whom the Software is
* furnished to do so, subject to the following conditions:
*
* The above copyright notice and this permission notice shall be included in
* all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
* AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
* OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
* THE SOFTWARE.
*/
#ifndef MICROPY_INCLUDED_STMHAL_IRQ_H
#define MICROPY_INCLUDED_STMHAL_IRQ_H
// these states correspond to values from query_irq, enable_irq and disable_irq
#define IRQ_STATE_DISABLED (0x00000001)
#define IRQ_STATE_ENABLED (0x00000000)
// Enable this to get a count for the number of times each irq handler is called,
// accessible via pyb.irq_stats().
#define IRQ_ENABLE_STATS (0)
#if IRQ_ENABLE_STATS
extern uint32_t irq_stats[FPU_IRQn + 1];
#define IRQ_ENTER(irq) ++irq_stats[irq]
#define IRQ_EXIT(irq)
#else
#define IRQ_ENTER(irq)
#define IRQ_EXIT(irq)
#endif
static inline mp_uint_t query_irq(void) {
return __get_PRIMASK();
}
// enable_irq and disable_irq are defined inline in mpconfigport.h
#if __CORTEX_M >= 0x03
// irqs with a priority value greater or equal to "pri" will be disabled
// "pri" should be between 1 and 15 inclusive
static inline uint32_t raise_irq_pri(uint32_t pri) {
uint32_t basepri = __get_BASEPRI();
// If non-zero, the processor does not process any exception with a
// priority value greater than or equal to BASEPRI.
// When writing to BASEPRI_MAX the write goes to BASEPRI only if either:
// - Rn is non-zero and the current BASEPRI value is 0
// - Rn is non-zero and less than the current BASEPRI value
pri <<= (8 - __NVIC_PRIO_BITS);
__ASM volatile ("msr basepri_max, %0" : : "r" (pri) : "memory");
return basepri;
}
// "basepri" should be the value returned from raise_irq_pri
static inline void restore_irq_pri(uint32_t basepri) {
__set_BASEPRI(basepri);
}
#endif
MP_DECLARE_CONST_FUN_OBJ_0(pyb_wfi_obj);
MP_DECLARE_CONST_FUN_OBJ_0(pyb_disable_irq_obj);
MP_DECLARE_CONST_FUN_OBJ_VAR_BETWEEN(pyb_enable_irq_obj);
MP_DECLARE_CONST_FUN_OBJ_0(pyb_irq_stats_obj);
// IRQ priority definitions.
//
// Lower number implies higher interrupt priority.
//
// The default priority grouping is set to NVIC_PRIORITYGROUP_4 in the
// HAL_Init function. This corresponds to 4 bits for the priority field
// and 0 bits for the sub-priority field (which means that for all intensive
// purposes that the sub-priorities below are ignored).
//
// While a given interrupt is being processed, only higher priority (lower number)
// interrupts will preempt a given interrupt. If sub-priorities are active
// then the sub-priority determines the order that pending interrupts of
// a given priority are executed. This is only meaningful if 2 or more
// interrupts of the same priority are pending at the same time.
//
// The priority of the SysTick timer is determined from the TICK_INT_PRIORITY
// value which is normally set to 0 in the stm32f4xx_hal_conf.h file.
//
// The following interrupts are arranged from highest priority to lowest
// priority to make it a bit easier to figure out.
// Priority Sub-Priority
// -------- ------------
//#def IRQ_PRI_SYSTICK 0
//#def IRQ_SUBPRI_SYSTICK 0
// The UARTs have no FIFOs, so if they don't get serviced quickly then characters
// get dropped. The handling for each character only consumes about 0.5 usec
#define IRQ_PRI_UART 1
#define IRQ_SUBPRI_UART 0
// Flash IRQ must be higher priority than interrupts of all those components
// that rely on the flash storage.
#define IRQ_PRI_FLASH 2
#define IRQ_SUBPRI_FLASH 0
// SDIO must be higher priority than DMA for SDIO DMA transfers to work.
#define IRQ_PRI_SDIO 4
#define IRQ_SUBPRI_SDIO 0
// DMA should be higher priority than USB, since USB Mass Storage calls
// into the sdcard driver which waits for the DMA to complete.
#define IRQ_PRI_DMA 5
#define IRQ_SUBPRI_DMA 0
#define IRQ_PRI_OTG_FS 6
#define IRQ_SUBPRI_OTG_FS 0
#define IRQ_PRI_OTG_HS 6
#define IRQ_SUBPRI_OTG_HS 0
#define IRQ_PRI_TIM5 6
#define IRQ_SUBPRI_TIM5 0
#define IRQ_PRI_CAN 7
#define IRQ_SUBPRI_CAN 0
// Interrupt priority for non-special timers.
#define IRQ_PRI_TIMX 13
#define IRQ_SUBPRI_TIMX 0
#define IRQ_PRI_EXTINT 14
#define IRQ_SUBPRI_EXTINT 0
// PENDSV should be at the lowst priority so that other interrupts complete
// before exception is raised.
#define IRQ_PRI_PENDSV 15
#define IRQ_SUBPRI_PENDSV 0
#define IRQ_PRI_RTC_WKUP 15
#define IRQ_SUBPRI_RTC_WKUP 0
#endif // MICROPY_INCLUDED_STMHAL_IRQ_H