micropython/ports/mimxrt/hal/flexspi_flash_config.h

Ignoring revisions in .git-blame-ignore-revs. Click here to bypass and see the normal blame view.

264 lines
12 KiB
C
Raw Normal View History

/*
* Copyright 2018 NXP
* All rights reserved.
*
* SPDX-License-Identifier: BSD-3-Clause
*/
#ifndef __FLEXSPI_FLASH_CONFIG__
#define __FLEXSPI_FLASH_CONFIG__
#include <stdint.h>
#include <stdbool.h>
#include "fsl_flexspi.h"
/*! @name Driver version */
/*@{*/
/*! @brief XIP_BOARD driver version 2.0.0. */
#define FSL_XIP_BOARD_DRIVER_VERSION (MAKE_VERSION(2, 0, 0))
/*@}*/
/* FLEXSPI memory config block related definitions */
#define FLEXSPI_CFG_BLK_TAG (0x42464346UL) // ascii "FCFB" Big Endian
#define FLEXSPI_CFG_BLK_VERSION (0x56010400UL) // V1.4.0
#define FLEXSPI_CFG_BLK_SIZE (512)
/* FLEXSPI Feature related definitions */
#define FLEXSPI_FEATURE_HAS_PARALLEL_MODE 1
/* Lookup table related definitions */
#define CMD_INDEX_READ 0
#define CMD_INDEX_READSTATUS 1
#define CMD_INDEX_WRITEENABLE 2
#define CMD_INDEX_WRITE 4
#define CMD_LUT_SEQ_IDX_READ 0
#define CMD_LUT_SEQ_IDX_READSTATUS 1
#define CMD_LUT_SEQ_IDX_WRITEENABLE 3
#define CMD_LUT_SEQ_IDX_WRITE 9
#define CMD_SDR 0x01
#define CMD_DDR 0x21
#define RADDR_SDR 0x02
#define RADDR_DDR 0x22
#define CADDR_SDR 0x03
#define CADDR_DDR 0x23
#define MODE1_SDR 0x04
#define MODE1_DDR 0x24
#define MODE2_SDR 0x05
#define MODE2_DDR 0x25
#define MODE4_SDR 0x06
#define MODE4_DDR 0x26
#define MODE8_SDR 0x07
#define MODE8_DDR 0x27
#define WRITE_SDR 0x08
#define WRITE_DDR 0x28
#define READ_SDR 0x09
#define READ_DDR 0x29
#define LEARN_SDR 0x0A
#define LEARN_DDR 0x2A
#define DATSZ_SDR 0x0B
#define DATSZ_DDR 0x2B
#define DUMMY_SDR 0x0C
#define DUMMY_DDR 0x2C
#define DUMMY_RWDS_SDR 0x0D
#define DUMMY_RWDS_DDR 0x2D
#define JMP_ON_CS 0x1F
#define STOP 0
#define FLEXSPI_1PAD 0
#define FLEXSPI_2PAD 1
#define FLEXSPI_4PAD 2
#define FLEXSPI_8PAD 3
#define FLEXSPI_LUT_SEQ(cmd0, pad0, op0, cmd1, pad1, op1) \
(FLEXSPI_LUT_OPERAND0(op0) | FLEXSPI_LUT_NUM_PADS0(pad0) | FLEXSPI_LUT_OPCODE0(cmd0) | FLEXSPI_LUT_OPERAND1(op1) | \
FLEXSPI_LUT_NUM_PADS1(pad1) | FLEXSPI_LUT_OPCODE1(cmd1))
// !@brief Definitions for FlexSPI Serial Clock Frequency
typedef enum _FlexSpiSerialClockFreq
{
kFlexSpiSerialClk_30MHz = 1,
kFlexSpiSerialClk_50MHz = 2,
kFlexSpiSerialClk_60MHz = 3,
kFlexSpiSerialClk_75MHz = 4,
kFlexSpiSerialClk_80MHz = 5,
kFlexSpiSerialClk_100MHz = 6,
kFlexSpiSerialClk_133MHz = 7,
kFlexSpiSerialClk_166MHz = 8,
} flexspi_serial_clk_freq_t;
// !@brief FlexSPI clock configuration type
enum
{
kFlexSpiClk_SDR, // !< Clock configure for SDR mode
kFlexSpiClk_DDR, // !< Clock configurat for DDR mode
};
// !@brief FlexSPI Read Sample Clock Source definition
typedef enum _FlashReadSampleClkSource
{
kFlexSPIReadSampleClk_LoopbackInternally = 0,
kFlexSPIReadSampleClk_LoopbackFromDqsPad = 1,
kFlexSPIReadSampleClk_LoopbackFromSckPad = 2,
kFlexSPIReadSampleClk_ExternalInputFromDqsPad = 3,
} flexspi_read_sample_clk_t;
// !@brief Misc feature bit definitions
enum
{
kFlexSpiMiscOffset_DiffClkEnable = 0, // !< Bit for Differential clock enable
kFlexSpiMiscOffset_Ck2Enable = 1, // !< Bit for CK2 enable
kFlexSpiMiscOffset_ParallelEnable = 2, // !< Bit for Parallel mode enable
kFlexSpiMiscOffset_WordAddressableEnable = 3, // !< Bit for Word Addressable enable
kFlexSpiMiscOffset_SafeConfigFreqEnable = 4, // !< Bit for Safe Configuration Frequency enable
kFlexSpiMiscOffset_PadSettingOverrideEnable = 5, // !< Bit for Pad setting override enable
kFlexSpiMiscOffset_DdrModeEnable = 6, // !< Bit for DDR clock confiuration indication.
};
// !@brief Flash Type Definition
enum
{
kFlexSpiDeviceType_SerialNOR = 1, // !< Flash devices are Serial NOR
kFlexSpiDeviceType_SerialNAND = 2, // !< Flash devices are Serial NAND
kFlexSpiDeviceType_SerialRAM = 3, // !< Flash devices are Serial RAM/HyperFLASH
kFlexSpiDeviceType_MCP_NOR_NAND = 0x12, // !< Flash device is MCP device, A1 is Serial NOR, A2 is Serial NAND
kFlexSpiDeviceType_MCP_NOR_RAM = 0x13, // !< Flash device is MCP device, A1 is Serial NOR, A2 is Serial RAMs
};
// !@brief Flash Pad Definitions
enum
{
kSerialFlash_1Pad = 1,
kSerialFlash_2Pads = 2,
kSerialFlash_4Pads = 4,
kSerialFlash_8Pads = 8,
};
// !@brief FlexSPI LUT Sequence structure
typedef struct _lut_sequence
{
uint8_t seqNum; // !< Sequence Number, valid number: 1-16
uint8_t seqId; // !< Sequence Index, valid number: 0-15
uint16_t reserved;
} flexspi_lut_seq_t;
// !@brief Flash Configuration Command Type
enum
{
kDeviceConfigCmdType_Generic, // !< Generic command, for example: configure dummy cycles, drive strength, etc
kDeviceConfigCmdType_QuadEnable, // !< Quad Enable command
kDeviceConfigCmdType_Spi2Xpi, // !< Switch from SPI to DPI/QPI/OPI mode
kDeviceConfigCmdType_Xpi2Spi, // !< Switch from DPI/QPI/OPI to SPI mode
kDeviceConfigCmdType_Spi2NoCmd, // !< Switch to 0-4-4/0-8-8 mode
kDeviceConfigCmdType_Reset, // !< Reset device command
};
// !@brief FlexSPI Memory Configuration Block
typedef struct _FlexSPIConfig
{
uint32_t tag; // !< [0x000-0x003] Tag, fixed value 0x42464346UL
uint32_t version; // !< [0x004-0x007] Version,[31:24] -'V', [23:16] - Major, [15:8] - Minor, [7:0] - bugfix
uint32_t reserved0; // !< [0x008-0x00b] Reserved for future use
uint8_t readSampleClkSrc; // !< [0x00c-0x00c] Read Sample Clock Source, valid value: 0/1/3
uint8_t csHoldTime; // !< [0x00d-0x00d] CS hold time, default value: 3
uint8_t csSetupTime; // !< [0x00e-0x00e] CS setup time, default value: 3
uint8_t columnAddressWidth; // !< [0x00f-0x00f] Column Address with, for HyperBus protocol, it is fixed to 3, For
// ! Serial NAND, need to refer to datasheet
uint8_t deviceModeCfgEnable; // !< [0x010-0x010] Device Mode Configure enable flag, 1 - Enable, 0 - Disable
uint8_t deviceModeType; // !< [0x011-0x011] Specify the configuration command type:Quad Enable, DPI/QPI/OPI switch,
// ! Generic configuration, etc.
uint16_t waitTimeCfgCommands; // !< [0x012-0x013] Wait time for all configuration commands, unit: 100us, Used for
// ! DPI/QPI/OPI switch or reset command
flexspi_lut_seq_t deviceModeSeq; // !< [0x014-0x017] Device mode sequence info, [7:0] - LUT sequence id, [15:8] - LUt
// ! sequence number, [31:16] Reserved
uint32_t deviceModeArg; // !< [0x018-0x01b] Argument/Parameter for device configuration
uint8_t configCmdEnable; // !< [0x01c-0x01c] Configure command Enable Flag, 1 - Enable, 0 - Disable
uint8_t configModeType[3]; // !< [0x01d-0x01f] Configure Mode Type, similar as deviceModeTpe
flexspi_lut_seq_t
configCmdSeqs[3]; // !< [0x020-0x02b] Sequence info for Device Configuration command, similar as deviceModeSeq
uint32_t reserved1; // !< [0x02c-0x02f] Reserved for future use
uint32_t configCmdArgs[3]; // !< [0x030-0x03b] Arguments/Parameters for device Configuration commands
uint32_t reserved2; // !< [0x03c-0x03f] Reserved for future use
uint32_t controllerMiscOption; // !< [0x040-0x043] Controller Misc Options, see Misc feature bit definitions for more
// ! details
uint8_t deviceType; // !< [0x044-0x044] Device Type: See Flash Type Definition for more details
uint8_t sflashPadType; // !< [0x045-0x045] Serial Flash Pad Type: 1 - Single, 2 - Dual, 4 - Quad, 8 - Octal
uint8_t serialClkFreq; // !< [0x046-0x046] Serial Flash Frequency, device specific definitions, See System Boot
// ! Chapter for more details
uint8_t lutCustomSeqEnable; // !< [0x047-0x047] LUT customization Enable, it is required if the program/erase cannot
// ! be done using 1 LUT sequence, currently, only applicable to HyperFLASH
uint32_t reserved3[2]; // !< [0x048-0x04f] Reserved for future use
uint32_t sflashA1Size; // !< [0x050-0x053] Size of Flash connected to A1
uint32_t sflashA2Size; // !< [0x054-0x057] Size of Flash connected to A2
uint32_t sflashB1Size; // !< [0x058-0x05b] Size of Flash connected to B1
uint32_t sflashB2Size; // !< [0x05c-0x05f] Size of Flash connected to B2
uint32_t csPadSettingOverride; // !< [0x060-0x063] CS pad setting override value
uint32_t sclkPadSettingOverride; // !< [0x064-0x067] SCK pad setting override value
uint32_t dataPadSettingOverride; // !< [0x068-0x06b] data pad setting override value
uint32_t dqsPadSettingOverride; // !< [0x06c-0x06f] DQS pad setting override value
uint32_t timeoutInMs; // !< [0x070-0x073] Timeout threshold for read status command
uint32_t commandInterval; // !< [0x074-0x077] CS deselect interval between two commands
uint16_t dataValidTime[2]; // !< [0x078-0x07b] CLK edge to data valid time for PORT A and PORT B, in terms of 0.1ns
uint16_t busyOffset; // !< [0x07c-0x07d] Busy offset, valid value: 0-31
uint16_t busyBitPolarity; // !< [0x07e-0x07f] Busy flag polarity, 0 - busy flag is 1 when flash device is busy, 1 -
// ! busy flag is 0 when flash device is busy
uint32_t lookupTable[64]; // !< [0x080-0x17f] Lookup table holds Flash command sequences
flexspi_lut_seq_t lutCustomSeq[12]; // !< [0x180-0x1af] Customizable LUT Sequences
uint32_t reserved4[4]; // !< [0x1b0-0x1bf] Reserved for future use
} flexspi_mem_config_t;
/* */
#define NOR_CMD_LUT_SEQ_IDX_READ_NORMAL 0
#define NOR_CMD_LUT_SEQ_IDX_READSTATUSREG 1
#define NOR_CMD_LUT_SEQ_IDX_READ_FAST_QUAD 2
#define NOR_CMD_LUT_SEQ_IDX_WRITEENABLE 3
#define NOR_CMD_LUT_SEQ_IDX_READSTATUS_XPI 4
#define NOR_CMD_LUT_SEQ_IDX_ERASESECTOR 5
#define NOR_CMD_LUT_SEQ_IDX_WRITESTATUSREG 6
#define NOR_CMD_LUT_SEQ_IDX_PAGEPROGRAM_QUAD 7
#define NOR_CMD_LUT_SEQ_IDX_READID 8
#define NOR_CMD_LUT_SEQ_IDX_PAGEPROGRAM 9
#define NOR_CMD_LUT_SEQ_IDX_ENTERQPI 10
#define NOR_CMD_LUT_SEQ_IDX_CHIPERASE 11
#define NOR_CMD_LUT_SEQ_IDX_EXITQPI 12
#define HYPERFLASH_CMD_LUT_SEQ_IDX_READDATA 0
#define HYPERFLASH_CMD_LUT_SEQ_IDX_WRITEDATA 1
#define HYPERFLASH_CMD_LUT_SEQ_IDX_READSTATUS 2
#define HYPERFLASH_CMD_LUT_SEQ_IDX_WRITEENABLE 4
#define HYPERFLASH_CMD_LUT_SEQ_IDX_ERASESECTOR 6
#define HYPERFLASH_CMD_LUT_SEQ_IDX_PAGEPROGRAM 10
#define HYPERFLASH_CMD_LUT_SEQ_IDX_ERASECHIP 12
/*
* Serial NOR configuration block
*/
typedef struct _flexspi_nor_config
{
flexspi_mem_config_t memConfig; // !< Common memory configuration info via FlexSPI
uint32_t pageSize; // !< Page size of Serial NOR
uint32_t sectorSize; // !< Sector size of Serial NOR
uint8_t ipcmdSerialClkFreq; // !< Clock frequency for IP command
uint8_t isUniformBlockSize; // !< Sector/Block size is the same
uint8_t reserved0[2]; // !< Reserved for future use
uint8_t serialNorType; // !< Serial NOR Flash type: 0/1/2/3
uint8_t needExitNoCmdMode; // !< Need to exit NoCmd mode before other IP command
uint8_t halfClkForNonReadCmd; // !< Half the Serial Clock for non-read command: true/false
uint8_t needRestoreNoCmdMode; // !< Need to Restore NoCmd mode after IP command execution
uint32_t blockSize; // !< Block size
uint32_t reserve2[11]; // !< Reserved for future use
} flexspi_nor_config_t;
#define FLASH_BUSY_STATUS_POL 0
#define FLASH_BUSY_STATUS_OFFSET 0
#ifdef __cplusplus
extern "C" {
#endif
#ifdef __cplusplus
}
#endif
#endif /* __FLEXSPI_FLASH_CONFIG__ */