micropython/cc3200/hal/inc/hw_camera.h

520 lines
29 KiB
C
Raw Normal View History

//*****************************************************************************
//
// Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/
//
//
// Redistribution and use in source and binary forms, with or without
// modification, are permitted provided that the following conditions
// are met:
//
// Redistributions of source code must retain the above copyright
// notice, this list of conditions and the following disclaimer.
//
// Redistributions in binary form must reproduce the above copyright
// notice, this list of conditions and the following disclaimer in the
// documentation and/or other materials provided with the
// distribution.
//
// Neither the name of Texas Instruments Incorporated nor the names of
// its contributors may be used to endorse or promote products derived
// from this software without specific prior written permission.
//
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
// "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
// LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
// A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
// OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
// SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
// LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
// DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
// THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
// (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
// OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
//
//*****************************************************************************
#ifndef __HW_CAMERA_H__
#define __HW_CAMERA_H__
//*****************************************************************************
//
// The following are defines for the CAMERA register offsets.
//
//*****************************************************************************
#define CAMERA_O_CC_REVISION 0x00000000 // This register contains the IP
// revision code ( Parallel Mode)
#define CAMERA_O_CC_SYSCONFIG 0x00000010 // This register controls the
// various parameters of the OCP
// interface (CCP and Parallel Mode)
#define CAMERA_O_CC_SYSSTATUS 0x00000014 // This register provides status
// information about the module
// excluding the interrupt status
// information (CCP and Parallel
// Mode)
#define CAMERA_O_CC_IRQSTATUS 0x00000018 // The interrupt status regroups
// all the status of the module
// internal events that can generate
// an interrupt (CCP & Parallel
// Mode)
#define CAMERA_O_CC_IRQENABLE 0x0000001C // The interrupt enable register
// allows to enable/disable the
// module internal sources of
// interrupt on an event-by-event
// basis (CCP & Parallel Mode)
#define CAMERA_O_CC_CTRL 0x00000040 // This register controls the
// various parameters of the Camera
// Core block (CCP & Parallel Mode)
#define CAMERA_O_CC_CTRL_DMA 0x00000044 // This register controls the DMA
// interface of the Camera Core
// block (CCP & Parallel Mode)
#define CAMERA_O_CC_CTRL_XCLK 0x00000048 // This register control the value
// of the clock divisor used to
// generate the external clock
// (Parallel Mode)
#define CAMERA_O_CC_FIFO_DATA 0x0000004C // This register allows to write to
// the FIFO and read from the FIFO
// (CCP & Parallel Mode)
#define CAMERA_O_CC_TEST 0x00000050 // This register shows the status
// of some important variables of
// the camera core module (CCP &
// Parallel Mode)
#define CAMERA_O_CC_GEN_PAR 0x00000054 // This register shows the values
// of the generic parameters of the
// module
//******************************************************************************
//
// The following are defines for the bit fields in the
// CAMERA_O_CC_REVISION register.
//
//******************************************************************************
#define CAMERA_CC_REVISION_REV_M \
0x000000FF // IP revision [7:4] Major revision
// [3:0] Minor revision Examples:
// 0x10 for 1.0 0x21 for 2.1
#define CAMERA_CC_REVISION_REV_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// CAMERA_O_CC_SYSCONFIG register.
//
//******************************************************************************
#define CAMERA_CC_SYSCONFIG_S_IDLE_MODE_M \
0x00000018 // Slave interface power management
// req/ack control """00""
// Force-idle. An idle request is
// acknoledged unconditionally"
// """01"" No-idle. An idle request
// is never acknowledged" """10""
// reserved (Smart-idle not
// implemented)"
#define CAMERA_CC_SYSCONFIG_S_IDLE_MODE_S 3
#define CAMERA_CC_SYSCONFIG_SOFT_RESET \
0x00000002 // Software reset. Set this bit to
// 1 to trigger a module reset. The
// bit is automatically reset by the
// hardware. During reset it always
// returns 0. 0 Normal mode 1 The
// module is reset
#define CAMERA_CC_SYSCONFIG_AUTO_IDLE \
0x00000001 // Internal OCP clock gating
// strategy 0 OCP clock is
// free-running 1 Automatic OCP
// clock gating strategy is applied
// based on the OCP interface
// activity
//******************************************************************************
//
// The following are defines for the bit fields in the
// CAMERA_O_CC_SYSSTATUS register.
//
//******************************************************************************
#define CAMERA_CC_SYSSTATUS_RESET_DONE2 \
0x00000001 // Internal Reset Monitoring 0
// Internal module reset is on-going
// 1 Reset completed
//******************************************************************************
//
// The following are defines for the bit fields in the
// CAMERA_O_CC_IRQSTATUS register.
//
//******************************************************************************
#define CAMERA_CC_IRQSTATUS_FS_IRQ \
0x00080000 // Frame Start has occurred 0 Event
// false "1 Event is true
// (""pending"")" 0 Event status bit
// unchanged 1 Event status bit is
// reset
#define CAMERA_CC_IRQSTATUS_LE_IRQ \
0x00040000 // Line End has occurred 0 Event
// false "1 Event is true
// (""pending"")" 0 Event status bit
// unchanged 1 Event status bit is
// reset
#define CAMERA_CC_IRQSTATUS_LS_IRQ \
0x00020000 // Line Start has occurred 0 Event
// false "1 Event is true
// (""pending"")" 0 Event status bit
// unchanged 1 Event status bit is
// reset
#define CAMERA_CC_IRQSTATUS_FE_IRQ \
0x00010000 // Frame End has occurred 0 Event
// false "1 Event is true
// (""pending"")" 0 Event status bit
// unchanged 1 Event status bit is
// reset
#define CAMERA_CC_IRQSTATUS_FSP_ERR_IRQ \
0x00000800 // FSP code error 0 Event false "1
// Event is true (""pending"")" 0
// Event status bit unchanged 1
// Event status bit is reset
#define CAMERA_CC_IRQSTATUS_FW_ERR_IRQ \
0x00000400 // Frame Height Error 0 Event false
// "1 Event is true (""pending"")" 0
// Event status bit unchanged 1
// Event status bit is reset
#define CAMERA_CC_IRQSTATUS_FSC_ERR_IRQ \
0x00000200 // False Synchronization Code 0
// Event false "1 Event is true
// (""pending"")" 0 Event status bit
// unchanged 1 Event status bit is
// reset
#define CAMERA_CC_IRQSTATUS_SSC_ERR_IRQ \
0x00000100 // Shifted Synchronization Code 0
// Event false "1 Event is true
// (""pending"")" 0 Event status bit
// unchanged 1 Event status bit is
// reset
#define CAMERA_CC_IRQSTATUS_FIFO_NONEMPTY_IRQ \
0x00000010 // FIFO is not empty 0 Event false
// "1 Event is true (""pending"")" 0
// Event status bit unchanged 1
// Event status bit is reset
#define CAMERA_CC_IRQSTATUS_FIFO_FULL_IRQ \
0x00000008 // FIFO is full 0 Event false "1
// Event is true (""pending"")" 0
// Event status bit unchanged 1
// Event status bit is reset
#define CAMERA_CC_IRQSTATUS_FIFO_THR_IRQ \
0x00000004 // FIFO threshold has been reached
// 0 Event false "1 Event is true
// (""pending"")" 0 Event status bit
// unchanged 1 Event status bit is
// reset
#define CAMERA_CC_IRQSTATUS_FIFO_OF_IRQ \
0x00000002 // FIFO overflow has occurred 0
// Event false "1 Event is true
// (""pending"")" 0 Event status bit
// unchanged 1 Event status bit is
// reset
#define CAMERA_CC_IRQSTATUS_FIFO_UF_IRQ \
0x00000001 // FIFO underflow has occurred 0
// Event false "1 Event is true
// (""pending"")" 0 Event status bit
// unchanged 1 Event status bit is
// reset
//******************************************************************************
//
// The following are defines for the bit fields in the
// CAMERA_O_CC_IRQENABLE register.
//
//******************************************************************************
#define CAMERA_CC_IRQENABLE_FS_IRQ_EN \
0x00080000 // Frame Start Interrupt Enable 0
// Event is masked 1 Event generates
// an interrupt when it occurs
#define CAMERA_CC_IRQENABLE_LE_IRQ_EN \
0x00040000 // Line End Interrupt Enable 0
// Event is masked 1 Event generates
// an interrupt when it occurs
#define CAMERA_CC_IRQENABLE_LS_IRQ_EN \
0x00020000 // Line Start Interrupt Enable 0
// Event is masked 1 Event generates
// an interrupt when it occurs
#define CAMERA_CC_IRQENABLE_FE_IRQ_EN \
0x00010000 // Frame End Interrupt Enable 0
// Event is masked 1 Event generates
// an interrupt when it occurs
#define CAMERA_CC_IRQENABLE_FSP_IRQ_EN \
0x00000800 // FSP code Interrupt Enable 0
// Event is masked 1 Event generates
// an interrupt when it occurs
#define CAMERA_CC_IRQENABLE_FW_ERR_IRQ_EN \
0x00000400 // Frame Height Error Interrupt
// Enable 0 Event is masked 1 Event
// generates an interrupt when it
// occurs
#define CAMERA_CC_IRQENABLE_FSC_ERR_IRQ_EN \
0x00000200 // False Synchronization Code
// Interrupt Enable 0 Event is
// masked 1 Event generates an
// interrupt when it occurs
#define CAMERA_CC_IRQENABLE_SSC_ERR_IRQ_EN \
0x00000100 // False Synchronization Code
// Interrupt Enable 0 Event is
// masked 1 Event generates an
// interrupt when it occurs
#define CAMERA_CC_IRQENABLE_FIFO_NONEMPTY_IRQ_EN \
0x00000010 // FIFO Threshold Interrupt Enable
// 0 Event is masked 1 Event
// generates an interrupt when it
// occurs
#define CAMERA_CC_IRQENABLE_FIFO_FULL_IRQ_EN \
0x00000008 // FIFO Threshold Interrupt Enable
// 0 Event is masked 1 Event
// generates an interrupt when it
// occurs
#define CAMERA_CC_IRQENABLE_FIFO_THR_IRQ_EN \
0x00000004 // FIFO Threshold Interrupt Enable
// 0 Event is masked 1 Event
// generates an interrupt when it
// occurs
#define CAMERA_CC_IRQENABLE_FIFO_OF_IRQ_EN \
0x00000002 // FIFO Overflow Interrupt Enable 0
// Event is masked 1 Event generates
// an interrupt when it occurs
#define CAMERA_CC_IRQENABLE_FIFO_UF_IRQ_EN \
0x00000001 // FIFO Underflow Interrupt Enable
// 0 Event is masked 1 Event
// generates an interrupt when it
// occurs
//******************************************************************************
//
// The following are defines for the bit fields in the CAMERA_O_CC_CTRL register.
//
//******************************************************************************
#define CAMERA_CC_CTRL_CC_IF_SYNCHRO \
0x00080000 // Synchronize all camera sensor
// inputs This must be set during
// the configuration phase before
// CC_EN set to '1'. This can be
// used in very high frequency to
// avoid dependancy to the IO
// timings. 0 No synchro (most of
// applications) 1 Synchro enabled
// (should never be required)
#define CAMERA_CC_CTRL_CC_RST 0x00040000 // Resets all the internal finite
// states machines of the camera
// core module - by writing a 1 to
// this bit. must be applied when
// CC_EN = 0 Reads returns 0
#define CAMERA_CC_CTRL_CC_FRAME_TRIG \
0x00020000 // Set the modality in which CC_EN
// works when a disabling of the
// sensor camera core is wanted "If
// CC_FRAME_TRIG = 1 by writing
// ""0"" to CC_EN" the module is
// disabled at the end of the frame
// "If CC_FRAME_TRIG = 0 by writing
// ""0"" to CC_EN" the module is
// disabled immediately
#define CAMERA_CC_CTRL_CC_EN 0x00010000 // Enables the sensor interface of
// the camera core module "By
// writing ""1"" to this field the
// module is enabled." "By writing
// ""0"" to this field the module is
// disabled at" the end of the frame
// if CC_FRAM_TRIG =1 and is
// disabled immediately if
// CC_FRAM_TRIG = 0
#define CAMERA_CC_CTRL_NOBT_SYNCHRO \
0x00002000 // Enables to start at the
// beginning of the frame or not in
// NoBT 0 Acquisition starts when
// Vertical synchro is high 1
// Acquisition starts when Vertical
// synchro goes from low to high
// (beginning of the frame) -
// Recommended.
#define CAMERA_CC_CTRL_BT_CORRECT \
0x00001000 // Enables the correction within
// the sync codes in BT mode 0
// correction is not enabled 1
// correction is enabled
#define CAMERA_CC_CTRL_PAR_ORDERCAM \
0x00000800 // Enables swap between image-data
// in parallel mode 0 swap is not
// enabled 1 swap is enabled
#define CAMERA_CC_CTRL_PAR_CLK_POL \
0x00000400 // Inverts the clock coming from
// the sensor in parallel mode 0
// clock not inverted - data sampled
// on rising edge 1 clock inverted -
// data sampled on falling edge
#define CAMERA_CC_CTRL_NOBT_HS_POL \
0x00000200 // Sets the polarity of the
// synchronization signals in NOBT
// parallel mode 0 CAM_P_HS is
// active high 1 CAM_P_HS is active
// low
#define CAMERA_CC_CTRL_NOBT_VS_POL \
0x00000100 // Sets the polarity of the
// synchronization signals in NOBT
// parallel mode 0 CAM_P_VS is
// active high 1 CAM_P_VS is active
// low
#define CAMERA_CC_CTRL_PAR_MODE_M \
0x0000000E // Sets the Protocol Mode of the
// Camera Core module in parallel
// mode (when CCP_MODE = 0) """000""
// Parallel NOBT 8-bit" """001""
// Parallel NOBT 10-bit" """010""
// Parallel NOBT 12-bit" """011""
// reserved" """100"" Parallet BT
// 8-bit" """101"" Parallel BT
// 10-bit" """110"" reserved"
// """111"" FIFO test mode. Refer to
// Table 12 - FIFO Write and Read
// access"
#define CAMERA_CC_CTRL_PAR_MODE_S 1
#define CAMERA_CC_CTRL_CCP_MODE 0x00000001 // Set the Camera Core in CCP mode
// 0 CCP mode disabled 1 CCP mode
// enabled
//******************************************************************************
//
// The following are defines for the bit fields in the
// CAMERA_O_CC_CTRL_DMA register.
//
//******************************************************************************
#define CAMERA_CC_CTRL_DMA_DMA_EN \
0x00000100 // Sets the number of dma request
// lines 0 DMA interface disabled
// The DMA request line stays
// inactive 1 DMA interface enabled
// The DMA request line is
// operational
#define CAMERA_CC_CTRL_DMA_FIFO_THRESHOLD_M \
0x0000007F // Sets the threshold of the FIFO
// the assertion of the dmarequest
// line takes place when the
// threshold is reached.
// """0000000"" threshold set to 1"
// """0000001"" threshold set to 2"
// … """1111111"" threshold set to
// 128"
#define CAMERA_CC_CTRL_DMA_FIFO_THRESHOLD_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// CAMERA_O_CC_CTRL_XCLK register.
//
//******************************************************************************
#define CAMERA_CC_CTRL_XCLK_XCLK_DIV_M \
0x0000001F // Sets the clock divisor value for
// CAM_XCLK generation. based on
// CAM_MCK (value of CAM_MCLK is
// 96MHz) """00000"" CAM_XCLK Stable
// Low Level" Divider not enabled
// """00001"" CAM_XCLK Stable High
// Level" Divider not enabled from 2
// to 30 CAM_XCLK = CAM_MCLK /
// XCLK_DIV """11111"" Bypass -
// CAM_XCLK = CAM_MCLK"
#define CAMERA_CC_CTRL_XCLK_XCLK_DIV_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// CAMERA_O_CC_FIFO_DATA register.
//
//******************************************************************************
#define CAMERA_CC_FIFO_DATA_FIFO_DATA_M \
0xFFFFFFFF // Writes the 32-bit word into the
// FIFO Reads the 32-bit word from
// the FIFO
#define CAMERA_CC_FIFO_DATA_FIFO_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the CAMERA_O_CC_TEST register.
//
//******************************************************************************
#define CAMERA_CC_TEST_FIFO_RD_POINTER_M \
0xFF000000 // FIFO READ Pointer This field
// shows the value of the FIFO read
// pointer Expected value ranges
// from 0 to 127
#define CAMERA_CC_TEST_FIFO_RD_POINTER_S 24
#define CAMERA_CC_TEST_FIFO_WR_POINTER_M \
0x00FF0000 // FIFO WRITE pointer This field
// shows the value of the FIFO write
// pointer Expected value ranges
// from 0 to 127
#define CAMERA_CC_TEST_FIFO_WR_POINTER_S 16
#define CAMERA_CC_TEST_FIFO_LEVEL_M \
0x0000FF00 // FIFO level (how many 32-bit
// words the FIFO contains) This
// field shows the value of the FIFO
// level and can assume values from
// 0 to 128
#define CAMERA_CC_TEST_FIFO_LEVEL_S 8
#define CAMERA_CC_TEST_FIFO_LEVEL_PEAK_M \
0x000000FF // FIFO level peak This field shows
// the max value of the FIFO level
// and can assume values from 0 to
// 128
#define CAMERA_CC_TEST_FIFO_LEVEL_PEAK_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// CAMERA_O_CC_GEN_PAR register.
//
//******************************************************************************
#define CAMERA_CC_GEN_PAR_CC_FIFO_DEPTH_M \
0x00000007 // Camera Core FIFO DEPTH generic
// parameter
#define CAMERA_CC_GEN_PAR_CC_FIFO_DEPTH_S 0
#endif // __HW_CAMERA_H__