micropython/ports/samd/mcu/samd21/clock_config.c

Ignoring revisions in .git-blame-ignore-revs. Click here to bypass and see the normal blame view.

215 lines
8.2 KiB
C
Raw Normal View History

/*
* This file is part of the MicroPython project, http://micropython.org/
*
* This file provides functions for configuring the clocks.
*
* The MIT License (MIT)
*
* Copyright (c) 2022 Robert Hammelrath
*
* Permission is hereby granted, free of charge, to any person obtaining a copy
* of this software and associated documentation files (the "Software"), to deal
* in the Software without restriction, including without limitation the rights
* to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
* copies of the Software, and to permit persons to whom the Software is
* furnished to do so, subject to the following conditions:
*
* The above copyright notice and this permission notice shall be included in
* all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
* AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
* OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
* THE SOFTWARE.
*/
#include <stdint.h>
#include "py/runtime.h"
#include "py/mphal.h"
#include "samd_soc.h"
static uint32_t cpu_freq = CPU_FREQ;
static uint32_t peripheral_freq = DFLL48M_FREQ;
static uint32_t dfll48m_calibration;
int sercom_gclk_id[] = {
GCLK_CLKCTRL_ID_SERCOM0_CORE, GCLK_CLKCTRL_ID_SERCOM1_CORE,
GCLK_CLKCTRL_ID_SERCOM2_CORE, GCLK_CLKCTRL_ID_SERCOM3_CORE,
GCLK_CLKCTRL_ID_SERCOM4_CORE, GCLK_CLKCTRL_ID_SERCOM5_CORE
};
uint32_t get_cpu_freq(void) {
return cpu_freq;
}
uint32_t get_peripheral_freq(void) {
return peripheral_freq;
}
void set_cpu_freq(uint32_t cpu_freq_arg) {
cpu_freq = cpu_freq_arg;
}
void check_usb_recovery_mode(void) {
#if !MICROPY_HW_XOSC32K
mp_hal_delay_ms(500);
// Check USB status. If not connected, switch DFLL48M back to open loop
if (USB->DEVICE.DeviceEndpoint[0].EPCFG.reg == 0) {
// Set/keep the open loop mode of the device.
SYSCTRL->DFLLVAL.reg = dfll48m_calibration;
SYSCTRL->DFLLCTRL.reg = SYSCTRL_DFLLCTRL_CCDIS | SYSCTRL_DFLLCTRL_ENABLE;
}
#endif // MICROPY_HW_XOSC32K
}
void init_clocks(uint32_t cpu_freq) {
dfll48m_calibration = 0; // please the compiler
// SAMD21 Clock settings
// GCLK0: 48MHz from DFLL open loop mode or closed loop mode from 32k Crystal
// GCLK1: 32768 Hz from 32K ULP or DFLL48M
// GCLK2: 48MHz from DFLL for Peripherals
// GCLK3: 1Mhz for the us-counter (TC4/TC5)
// GCLK4: 32kHz from crystal, if present
// GCLK8: 1kHz clock for WDT
NVMCTRL->CTRLB.bit.MANW = 1; // errata "Spurious Writes"
NVMCTRL->CTRLB.bit.RWS = 1; // 1 read wait state for 48MHz
#if MICROPY_HW_XOSC32K
// Set up OSC32K according datasheet 17.6.3
SYSCTRL->XOSC32K.reg = SYSCTRL_XOSC32K_STARTUP(0x3) | SYSCTRL_XOSC32K_EN32K |
SYSCTRL_XOSC32K_XTALEN;
SYSCTRL->XOSC32K.bit.ENABLE = 1;
while (SYSCTRL->PCLKSR.bit.XOSC32KRDY == 0) {
}
// Set up the DFLL48 according to the data sheet 17.6.7.1.2
// Step 1: Set up the reference clock
#if MICROPY_HW_MCU_OSC32KULP
// Connect the GCLK1 to the XOSC32KULP
GCLK->GENDIV.reg = GCLK_GENDIV_ID(1) | GCLK_GENDIV_DIV(1);
GCLK->GENCTRL.reg = GCLK_GENCTRL_GENEN | GCLK_GENCTRL_SRC_OSCULP32K | GCLK_GENCTRL_ID(1);
#else
// Connect the GCLK1 to OSC32K via GCLK1 to the DFLL input and for further use.
GCLK->GENDIV.reg = GCLK_GENDIV_ID(1) | GCLK_GENDIV_DIV(1);
GCLK->GENCTRL.reg = GCLK_GENCTRL_GENEN | GCLK_GENCTRL_SRC_XOSC32K | GCLK_GENCTRL_ID(1);
#endif
while (GCLK->STATUS.bit.SYNCBUSY) {
}
// Connect the GCLK4 to OSC32K via GCLK1 to the DFLL input and for further use.
GCLK->GENDIV.reg = GCLK_GENDIV_ID(4) | GCLK_GENDIV_DIV(1);
GCLK->GENCTRL.reg = GCLK_GENCTRL_GENEN | GCLK_GENCTRL_SRC_XOSC32K | GCLK_GENCTRL_ID(4);
while (GCLK->STATUS.bit.SYNCBUSY) {
}
// Connect GCLK4 to the DFLL input and for further use.
GCLK->CLKCTRL.reg = GCLK_CLKCTRL_ID_DFLL48 | GCLK_CLKCTRL_GEN_GCLK4 | GCLK_CLKCTRL_CLKEN;
// Enable access to the DFLLCTRL reg acc. to Errata 1.2.1
SYSCTRL->DFLLCTRL.reg = SYSCTRL_DFLLCTRL_ENABLE;
while (SYSCTRL->PCLKSR.bit.DFLLRDY == 0) {
}
// Step 2: Set the coarse and fine values.
// Get the coarse value from the calib data. In case it is not set,
// set a midrange value.
uint32_t coarse = (*((uint32_t *)FUSES_DFLL48M_COARSE_CAL_ADDR) & FUSES_DFLL48M_COARSE_CAL_Msk)
>> FUSES_DFLL48M_COARSE_CAL_Pos;
if (coarse == 0x3f) {
coarse = 0x1f;
}
SYSCTRL->DFLLVAL.reg = SYSCTRL_DFLLVAL_COARSE(coarse) | SYSCTRL_DFLLVAL_FINE(512);
while (SYSCTRL->PCLKSR.bit.DFLLRDY == 0) {
}
// Step 3: Set the multiplication values. The offset of 16384 to the freq is for rounding.
SYSCTRL->DFLLMUL.reg = SYSCTRL_DFLLMUL_MUL((CPU_FREQ + 16384) / 32768) |
SYSCTRL_DFLLMUL_FSTEP(1) | SYSCTRL_DFLLMUL_CSTEP(1);
while (SYSCTRL->PCLKSR.bit.DFLLRDY == 0) {
}
// Step 4: Start the DFLL and wait for the PLL lock. We just wait for the fine lock, since
// coarse adjusting is bypassed.
SYSCTRL->DFLLCTRL.reg |= SYSCTRL_DFLLCTRL_MODE | SYSCTRL_DFLLCTRL_WAITLOCK | SYSCTRL_DFLLCTRL_STABLE |
SYSCTRL_DFLLCTRL_BPLCKC | SYSCTRL_DFLLCTRL_ENABLE;
while (SYSCTRL->PCLKSR.bit.DFLLLCKF == 0) {
}
#else // MICROPY_HW_XOSC32K
// Enable DFLL48M
SYSCTRL->DFLLCTRL.reg = SYSCTRL_DFLLCTRL_ENABLE;
while (!SYSCTRL->PCLKSR.bit.DFLLRDY) {
}
uint32_t coarse = (*((uint32_t *)FUSES_DFLL48M_COARSE_CAL_ADDR) & FUSES_DFLL48M_COARSE_CAL_Msk)
>> FUSES_DFLL48M_COARSE_CAL_Pos;
if (coarse == 0x3f) {
coarse = 0x1f;
}
SYSCTRL->DFLLVAL.reg = SYSCTRL_DFLLVAL_COARSE(coarse) | SYSCTRL_DFLLVAL_FINE(511);
#if MICROPY_HW_DFLL_USB_SYNC
// Configure the DFLL48M for USB clock recovery.
// Will have to switch back if no USB
SYSCTRL->DFLLSYNC.bit.READREQ = 1;
dfll48m_calibration = SYSCTRL->DFLLVAL.reg;
// Set the Multiplication factor.
SYSCTRL->DFLLMUL.reg = SYSCTRL_DFLLMUL_CSTEP(1) | SYSCTRL_DFLLMUL_FSTEP(1)
| SYSCTRL_DFLLMUL_MUL(48000);
// Set the mode to closed loop USB Recovery mode
SYSCTRL->DFLLCTRL.reg = SYSCTRL_DFLLCTRL_USBCRM | SYSCTRL_DFLLCTRL_CCDIS
| SYSCTRL_DFLLCTRL_MODE | SYSCTRL_DFLLCTRL_ENABLE;
#else
// Set/keep the open loop mode of the device.
SYSCTRL->DFLLCTRL.reg = SYSCTRL_DFLLCTRL_CCDIS | SYSCTRL_DFLLCTRL_ENABLE;
#endif
while (!SYSCTRL->PCLKSR.bit.DFLLRDY) {
}
// Enable 32768 Hz on GCLK1 for consistency
GCLK->GENDIV.reg = GCLK_GENDIV_ID(1) | GCLK_GENDIV_DIV(48016384 / 32768);
GCLK->GENCTRL.reg = GCLK_GENCTRL_GENEN | GCLK_GENCTRL_SRC_DFLL48M | GCLK_GENCTRL_ID(1);
while (GCLK->STATUS.bit.SYNCBUSY) {
}
#endif // MICROPY_HW_XOSC32K
// Enable GCLK output: 48M on both CCLK0 and GCLK2
GCLK->GENDIV.reg = GCLK_GENDIV_ID(0) | GCLK_GENDIV_DIV(1);
GCLK->GENCTRL.reg = GCLK_GENCTRL_GENEN | GCLK_GENCTRL_SRC_DFLL48M | GCLK_GENCTRL_ID(0);
while (GCLK->STATUS.bit.SYNCBUSY) {
}
GCLK->GENDIV.reg = GCLK_GENDIV_ID(2) | GCLK_GENDIV_DIV(1);
GCLK->GENCTRL.reg = GCLK_GENCTRL_GENEN | GCLK_GENCTRL_SRC_DFLL48M | GCLK_GENCTRL_ID(2);
while (GCLK->STATUS.bit.SYNCBUSY) {
}
// Enable GCLK output: 1MHz on GCLK3 for TC4
GCLK->GENDIV.reg = GCLK_GENDIV_ID(3) | GCLK_GENDIV_DIV(48);
GCLK->GENCTRL.reg = GCLK_GENCTRL_GENEN | GCLK_GENCTRL_SRC_DFLL48M | GCLK_GENCTRL_ID(3);
while (GCLK->STATUS.bit.SYNCBUSY) {
}
// Set GCLK8 to 1 kHz.
GCLK->GENDIV.reg = GCLK_GENDIV_ID(8) | GCLK_GENDIV_DIV(32);
GCLK->GENCTRL.reg = GCLK_GENCTRL_GENEN | GCLK_GENCTRL_SRC_OSCULP32K | GCLK_GENCTRL_ID(8);
while (GCLK->STATUS.bit.SYNCBUSY) {
}
}
void enable_sercom_clock(int id) {
// Enable synchronous clock. The bits are nicely arranged
PM->APBCMASK.reg |= 0x04 << id;
// Select multiplexer generic clock source and enable.
GCLK->CLKCTRL.reg = GCLK_CLKCTRL_CLKEN | GCLK_CLKCTRL_GEN_GCLK2 | sercom_gclk_id[id];
// Wait while it updates synchronously.
while (GCLK->STATUS.bit.SYNCBUSY) {
}
}