micropython/cc3200/hal/inc/hw_flash_ctrl.h

1863 lines
126 KiB
C
Raw Normal View History

//*****************************************************************************
//
// Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/
//
//
// Redistribution and use in source and binary forms, with or without
// modification, are permitted provided that the following conditions
// are met:
//
// Redistributions of source code must retain the above copyright
// notice, this list of conditions and the following disclaimer.
//
// Redistributions in binary form must reproduce the above copyright
// notice, this list of conditions and the following disclaimer in the
// documentation and/or other materials provided with the
// distribution.
//
// Neither the name of Texas Instruments Incorporated nor the names of
// its contributors may be used to endorse or promote products derived
// from this software without specific prior written permission.
//
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
// "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
// LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
// A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
// OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
// SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
// LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
// DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
// THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
// (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
// OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
//
//*****************************************************************************
#ifndef __HW_FLASH_CTRL_H__
#define __HW_FLASH_CTRL_H__
//*****************************************************************************
//
// The following are defines for the FLASH_CTRL register offsets.
//
//*****************************************************************************
#define FLASH_CTRL_O_FMA 0x00000000 // Flash Memory Address (FMA)
// offset 0x000 During a write
// operation this register contains
// a 4-byte-aligned address and
// specifies where the data is
// written. During erase operations
// this register contains a 1
// KB-aligned CPU byte address and
// specifies which block is erased.
// Note that the alignment
// requirements must be met by
// software or the results of the
// operation are unpredictable.
#define FLASH_CTRL_O_FMD 0x00000004 // Flash Memory Data (FMD) offset
// 0x004 This register contains the
// data to be written during the
// programming cycle or read during
// the read cycle. Note that the
// contents of this register are
// undefined for a read access of an
// execute-only block. This register
// is not used during erase cycles.
#define FLASH_CTRL_O_FMC 0x00000008 // Flash Memory Control (FMC)
// offset 0x008 When this register
// is written the Flash memory
// controller initiates the
// appropriate access cycle for the
// location specified by the Flash
// Memory Address (FMA) register .
// If the access is a write access
// the data contained in the Flash
// Memory Data (FMD) register is
// written to the specified address.
// This register must be the final
// register written and initiates
// the memory operation. The four
// control bits in the lower byte of
// this register are used to
// initiate memory operations.
#define FLASH_CTRL_O_FCRIS 0x0000000C // Flash Controller Raw Interrupt
// Status (FCRIS) offset 0x00C This
// register indicates that the Flash
// memory controller has an
// interrupt condition. An interrupt
// is sent to the interrupt
// controller only if the
// corresponding FCIM register bit
// is set.
#define FLASH_CTRL_O_FCIM 0x00000010 // Flash Controller Interrupt Mask
// (FCIM) offset 0x010 This register
// controls whether the Flash memory
// controller generates interrupts
// to the controller.
#define FLASH_CTRL_O_FCMISC 0x00000014 // Flash Controller Masked
// Interrupt Status and Clear
// (FCMISC) offset 0x014 This
// register provides two functions.
// First it reports the cause of an
// interrupt by indicating which
// interrupt source or sources are
// signalling the interrupt. Second
// it serves as the method to clear
// the interrupt reporting.
#define FLASH_CTRL_O_FMC2 0x00000020 // Flash Memory Control 2 (FMC2)
// offset 0x020 When this register
// is written the Flash memory
// controller initiates the
// appropriate access cycle for the
// location specified by the Flash
// Memory Address (FMA) register .
// If the access is a write access
// the data contained in the Flash
// Write Buffer (FWB) registers is
// written. This register must be
// the final register written as it
// initiates the memory operation.
#define FLASH_CTRL_O_FWBVAL 0x00000030 // Flash Write Buffer Valid
// (FWBVAL) offset 0x030 This
// register provides a bitwise
// status of which FWBn registers
// have been written by the
// processor since the last write of
// the Flash memory write buffer.
// The entries with a 1 are written
// on the next write of the Flash
// memory write buffer. This
// register is cleared after the
// write operation by hardware. A
// protection violation on the write
// operation also clears this
// status. Software can program the
// same 32 words to various Flash
// memory locations by setting the
// FWB[n] bits after they are
// cleared by the write operation.
// The next write operation then
// uses the same data as the
// previous one. In addition if a
// FWBn register change should not
// be written to Flash memory
// software can clear the
// corresponding FWB[n] bit to
// preserve the existing data when
// the next write operation occurs.
#define FLASH_CTRL_O_FWB1 0x00000100 // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB2 0x00000104 // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB3 0x00000108 // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB4 0x0000010C // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB5 0x00000110 // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB6 0x00000114 // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB7 0x00000118 // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB8 0x0000011C // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB9 0x00000120 // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB10 0x00000124 // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB11 0x00000128 // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB12 0x0000012C // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB13 0x00000130 // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB14 0x00000134 // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB15 0x00000138 // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB16 0x0000013C // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB17 0x00000140 // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB18 0x00000144 // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB19 0x00000148 // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB20 0x0000014C // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB21 0x00000150 // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB22 0x00000154 // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB23 0x00000158 // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB24 0x0000015C // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB25 0x00000160 // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB26 0x00000164 // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB27 0x00000168 // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB28 0x0000016C // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB29 0x00000170 // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB30 0x00000174 // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB31 0x00000178 // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FWB32 0x0000017C // Flash Write Buffer n (FWBn)
// offset 0x100 - 0x17C These 32
// registers hold the contents of
// the data to be written into the
// Flash memory on a buffered Flash
// memory write operation. The
// offset selects one of the 32-bit
// registers. Only FWBn registers
// that have been updated since the
// preceding buffered Flash memory
// write operation are written into
// the Flash memory so it is not
// necessary to write the entire
// bank of registers in order to
// write 1 or 2 words. The FWBn
// registers are written into the
// Flash memory with the FWB0
// register corresponding to the
// address contained in FMA. FWB1 is
// written to the address FMA+0x4
// etc. Note that only data bits
// that are 0 result in the Flash
// memory being modified. A data bit
// that is 1 leaves the content of
// the Flash memory bit at its
// previous value.
#define FLASH_CTRL_O_FSIZE 0x00000FC0 // Flash Size (FSIZE) offset 0xFC0
// This register indicates the size
// of the on-chip Flash memory.
// Important: This register should
// be used to determine the size of
// the Flash memory that is
// implemented on this
// microcontroller. However to
// support legacy software the DC0
// register is available. A read of
// the DC0 register correctly
// identifies legacy memory sizes.
// Software must use the FSIZE
// register for memory sizes that
// are not listed in the DC0
// register description.
#define FLASH_CTRL_O_SSIZE 0x00000FC4 // SRAM Size (SSIZE) offset 0xFC4
// This register indicates the size
// of the on-chip SRAM. Important:
// This register should be used to
// determine the size of the SRAM
// that is implemented on this
// microcontroller. However to
// support legacy software the DC0
// register is available. A read of
// the DC0 register correctly
// identifies legacy memory sizes.
// Software must use the SSIZE
// register for memory sizes that
// are not listed in the DC0
// register description.
//******************************************************************************
//
// The following are defines for the bit fields in the FLASH_CTRL_O_FMA register.
//
//******************************************************************************
#define FLASH_CTRL_FMA_OFFSET_M 0x0003FFFF // Address Offset Address offset in
// Flash memory where operation is
// performed except for nonvolatile
// registers
#define FLASH_CTRL_FMA_OFFSET_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the FLASH_CTRL_O_FMD register.
//
//******************************************************************************
#define FLASH_CTRL_FMD_DATA_M 0xFFFFFFFF // Data Value Data value for write
// operation.
#define FLASH_CTRL_FMD_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the FLASH_CTRL_O_FMC register.
//
//******************************************************************************
#define FLASH_CTRL_FMC_WRKEY_M 0xFFFF0000 // Flash Memory Write Key This
// field contains a write key which
// is used to minimize the incidence
// of accidental Flash memory
// writes. The value 0xA442 must be
// written into this field for a
// Flash memory write to occur.
// Writes to the FMC register
// without this WRKEY value are
// ignored. A read of this field
// returns the value 0.
#define FLASH_CTRL_FMC_WRKEY_S 16
#define FLASH_CTRL_FMC_COMT 0x00000008 // Commit Register Value This bit
// is used to commit writes to
// Flash-memory-resident registers
// and to monitor the progress of
// that process. Value Description 1
// Set this bit to commit (write)
// the register value to a
// Flash-memory-resident register.
// When read a 1 indicates that the
// previous commit access is not
// complete. 0 A write of 0 has no
// effect on the state of this bit.
// When read a 0 indicates that the
// previous commit access is
// complete.
#define FLASH_CTRL_FMC_MERASE1 0x00000004 // Mass Erase Flash Memory This bit
// is used to mass erase the Flash
// main memory and to monitor the
// progress of that process. Value
// Description 1 Set this bit to
// erase the Flash main memory. When
// read a 1 indicates that the
// previous mass erase access is not
// complete. 0 A write of 0 has no
// effect on the state of this bit.
// When read a 0 indicates that the
// previous mass erase access is
// complete.
#define FLASH_CTRL_FMC_ERASE 0x00000002 // Erase a Page of Flash Memory
// This bit is used to erase a page
// of Flash memory and to monitor
// the progress of that process.
// Value Description 1 Set this bit
// to erase the Flash memory page
// specified by the contents of the
// FMA register. When read a 1
// indicates that the previous page
// erase access is not complete. 0 A
// write of 0 has no effect on the
// state of this bit. When read a 0
// indicates that the previous page
// erase access is complete.
#define FLASH_CTRL_FMC_WRITE 0x00000001 // Write a Word into Flash Memory
// This bit is used to write a word
// into Flash memory and to monitor
// the progress of that process.
// Value Description 1 Set this bit
// to write the data stored in the
// FMD register into the Flash
// memory location specified by the
// contents of the FMA register.
// When read a 1 indicates that the
// write update access is not
// complete. 0 A write of 0 has no
// effect on the state of this bit.
// When read a 0 indicates that the
// previous write update access is
// complete.
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FCRIS register.
//
//******************************************************************************
#define FLASH_CTRL_FCRIS_PROGRIS \
0x00002000 // Program Verify Error Raw
// Interrupt Status Value
// Description 1 An interrupt is
// pending because the verify of a
// PROGRAM operation failed. 0 An
// interrupt has not occurred. This
// bit is cleared by writing a 1 to
// the PROGMISC bit in the FCMISC
// register.
#define FLASH_CTRL_FCRIS_ERRIS 0x00000800 // Erase Verify Error Raw Interrupt
// Status Value Description 1 An
// interrupt is pending because the
// verify of an ERASE operation
// failed. 0 An interrupt has not
// occurred. This bit is cleared by
// writing a 1 to the ERMISC bit in
// the FCMISC register.
#define FLASH_CTRL_FCRIS_INVDRIS \
0x00000400 // Invalid Data Raw Interrupt
// Status Value Description 1 An
// interrupt is pending because a
// bit that was previously
// programmed as a 0 is now being
// requested to be programmed as a
// 1. 0 An interrupt has not
// occurred. This bit is cleared by
// writing a 1 to the INVMISC bit in
// the FCMISC register.
#define FLASH_CTRL_FCRIS_VOLTRIS \
0x00000200 // Pump Voltage Raw Interrupt
// Status Value Description 1 An
// interrupt is pending because the
// regulated voltage of the pump
// went out of spec during the Flash
// operation and the operation was
// terminated. 0 An interrupt has
// not occurred. This bit is cleared
// by writing a 1 to the VOLTMISC
// bit in the FCMISC register.
#define FLASH_CTRL_FCRIS_ERIS 0x00000004 // EEPROM Raw Interrupt Status This
// bit provides status EEPROM
// operation. Value Description 1 An
// EEPROM interrupt has occurred. 0
// An EEPROM interrupt has not
// occurred. This bit is cleared by
// writing a 1 to the EMISC bit in
// the FCMISC register.
#define FLASH_CTRL_FCRIS_PRIS 0x00000002 // Programming Raw Interrupt Status
// This bit provides status on
// programming cycles which are
// write or erase actions generated
// through the FMC or FMC2 register
// bits (see page 537 and page 549).
// Value Description 1 The
// programming or erase cycle has
// completed. 0 The programming or
// erase cycle has not completed.
// This status is sent to the
// interrupt controller when the
// PMASK bit in the FCIM register is
// set. This bit is cleared by
// writing a 1 to the PMISC bit in
// the FCMISC register.
#define FLASH_CTRL_FCRIS_ARIS 0x00000001 // Access Raw Interrupt Status
// Value Description 1 A program or
// erase action was attempted on a
// block of Flash memory that
// contradicts the protection policy
// for that block as set in the
// FMPPEn registers. 0 No access has
// tried to improperly program or
// erase the Flash memory. This
// status is sent to the interrupt
// controller when the AMASK bit in
// the FCIM register is set. This
// bit is cleared by writing a 1 to
// the AMISC bit in the FCMISC
// register.
//******************************************************************************
//
// The following are defines for the bit fields in the FLASH_CTRL_O_FCIM register.
//
//******************************************************************************
#define FLASH_CTRL_FCIM_ILLMASK 0x00004000 // Illegal Address Interrupt Mask
// Value Description 1 An interrupt
// is sent to the interrupt
// controller when the ILLARIS bit
// is set. 0 The ILLARIS interrupt
// is suppressed and not sent to the
// interrupt controller.
#define FLASH_CTRL_FCIM_PROGMASK \
0x00002000 // PROGVER Interrupt Mask Value
// Description 1 An interrupt is
// sent to the interrupt controller
// when the PROGRIS bit is set. 0
// The PROGRIS interrupt is
// suppressed and not sent to the
// interrupt controller.
#define FLASH_CTRL_FCIM_PREMASK 0x00001000 // PREVER Interrupt Mask Value
// Description 1 An interrupt is
// sent to the interrupt controller
// when the PRERIS bit is set. 0 The
// PRERIS interrupt is suppressed
// and not sent to the interrupt
// controller.
#define FLASH_CTRL_FCIM_ERMASK 0x00000800 // ERVER Interrupt Mask Value
// Description 1 An interrupt is
// sent to the interrupt controller
// when the ERRIS bit is set. 0 The
// ERRIS interrupt is suppressed and
// not sent to the interrupt
// controller.
#define FLASH_CTRL_FCIM_INVDMASK \
0x00000400 // Invalid Data Interrupt Mask
// Value Description 1 An interrupt
// is sent to the interrupt
// controller when the INVDRIS bit
// is set. 0 The INVDRIS interrupt
// is suppressed and not sent to the
// interrupt controller.
#define FLASH_CTRL_FCIM_VOLTMASK \
0x00000200 // VOLT Interrupt Mask Value
// Description 1 An interrupt is
// sent to the interrupt controller
// when the VOLTRIS bit is set. 0
// The VOLTRIS interrupt is
// suppressed and not sent to the
// interrupt controller.
#define FLASH_CTRL_FCIM_LOCKMASK \
0x00000100 // LOCK Interrupt Mask Value
// Description 1 An interrupt is
// sent to the interrupt controller
// when the LOCKRIS bit is set. 0
// The LOCKRIS interrupt is
// suppressed and not sent to the
// interrupt controller.
#define FLASH_CTRL_FCIM_EMASK 0x00000004 // EEPROM Interrupt Mask Value
// Description 1 An interrupt is
// sent to the interrupt controller
// when the ERIS bit is set. 0 The
// ERIS interrupt is suppressed and
// not sent to the interrupt
// controller.
#define FLASH_CTRL_FCIM_PMASK 0x00000002 // Programming Interrupt Mask This
// bit controls the reporting of the
// programming raw interrupt status
// to the interrupt controller.
// Value Description 1 An interrupt
// is sent to the interrupt
// controller when the PRIS bit is
// set. 0 The PRIS interrupt is
// suppressed and not sent to the
// interrupt controller.
#define FLASH_CTRL_FCIM_AMASK 0x00000001 // Access Interrupt Mask This bit
// controls the reporting of the
// access raw interrupt status to
// the interrupt controller. Value
// Description 1 An interrupt is
// sent to the interrupt controller
// when the ARIS bit is set. 0 The
// ARIS interrupt is suppressed and
// not sent to the interrupt
// controller.
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FCMISC register.
//
//******************************************************************************
#define FLASH_CTRL_FCMISC_ILLMISC \
0x00004000 // Illegal Address Masked Interrupt
// Status and Clear Value
// Description 1 When read a 1
// indicates that an unmasked
// interrupt was signaled. Writing a
// 1 to this bit clears ILLAMISC and
// also the ILLARIS bit in the FCRIS
// register (see page 540). 0 When
// read a 0 indicates that an
// interrupt has not occurred. A
// write of 0 has no effect on the
// state of this bit.
#define FLASH_CTRL_FCMISC_PROGMISC \
0x00002000 // PROGVER Masked Interrupt Status
// and Clear Value Description 1
// When read a 1 indicates that an
// unmasked interrupt was signaled.
// Writing a 1 to this bit clears
// PROGMISC and also the PROGRIS bit
// in the FCRIS register (see page
// 540). 0 When read a 0 indicates
// that an interrupt has not
// occurred. A write of 0 has no
// effect on the state of this bit.
#define FLASH_CTRL_FCMISC_PREMISC \
0x00001000 // PREVER Masked Interrupt Status
// and Clear Value Description 1
// When read a 1 indicates that an
// unmasked interrupt was signaled.
// Writing a 1 to this bit clears
// PREMISC and also the PRERIS bit
// in the FCRIS register . 0 When
// read a 0 indicates that an
// interrupt has not occurred. A
// write of 0 has no effect on the
// state of this bit.
#define FLASH_CTRL_FCMISC_ERMISC \
0x00000800 // ERVER Masked Interrupt Status
// and Clear Value Description 1
// When read a 1 indicates that an
// unmasked interrupt was signaled.
// Writing a 1 to this bit clears
// ERMISC and also the ERRIS bit in
// the FCRIS register 0 When read a
// 0 indicates that an interrupt has
// not occurred. A write of 0 has no
// effect on the state of this bit.
#define FLASH_CTRL_FCMISC_INVDMISC \
0x00000400 // Invalid Data Masked Interrupt
// Status and Clear Value
// Description 1 When read a 1
// indicates that an unmasked
// interrupt was signaled. Writing a
// 1 to this bit clears INVDMISC and
// also the INVDRIS bit in the FCRIS
// register (see page 540). 0 When
// read a 0 indicates that an
// interrupt has not occurred. A
// write of 0 has no effect on the
// state of this bit.
#define FLASH_CTRL_FCMISC_VOLTMISC \
0x00000200 // VOLT Masked Interrupt Status and
// Clear Value Description 1 When
// read a 1 indicates that an
// unmasked interrupt was signaled.
// Writing a 1 to this bit clears
// VOLTMISC and also the VOLTRIS bit
// in the FCRIS register (see page
// 540). 0 When read a 0 indicates
// that an interrupt has not
// occurred. A write of 0 has no
// effect on the state of this bit.
#define FLASH_CTRL_FCMISC_LOCKMISC \
0x00000100 // LOCK Masked Interrupt Status and
// Clear Value Description 1 When
// read a 1 indicates that an
// unmasked interrupt was signaled.
// Writing a 1 to this bit clears
// LOCKMISC and also the LOCKRIS bit
// in the FCRIS register (see page
// 540). 0 When read a 0 indicates
// that an interrupt has not
// occurred. A write of 0 has no
// effect on the state of this bit.
#define FLASH_CTRL_FCMISC_EMISC 0x00000004 // EEPROM Masked Interrupt Status
// and Clear Value Description 1
// When read a 1 indicates that an
// unmasked interrupt was signaled.
// Writing a 1 to this bit clears
// EMISC and also the ERIS bit in
// the FCRIS register 0 When read a
// 0 indicates that an interrupt has
// not occurred. A write of 0 has no
// effect on the state of this bit.
#define FLASH_CTRL_FCMISC_PMISC 0x00000002 // Programming Masked Interrupt
// Status and Clear Value
// Description 1 When read a 1
// indicates that an unmasked
// interrupt was signaled because a
// programming cycle completed.
// Writing a 1 to this bit clears
// PMISC and also the PRIS bit in
// the FCRIS register 0 When read a
// 0 indicates that a programming
// cycle complete interrupt has not
// occurred. A write of 0 has no
// effect on the state of this bit.
#define FLASH_CTRL_FCMISC_AMISC 0x00000001 // Access Masked Interrupt Status
// and Clear Value Description 1
// When read a 1 indicates that an
// unmasked interrupt was signaled
// because a program or erase action
// was attempted on a block of Flash
// memory that contradicts the
// protection policy for that block
// as set in the FMPPEn registers.
// Writing a 1 to this bit clears
// AMISC and also the ARIS bit in
// the FCRIS register 0 When read a
// 0 indicates that no improper
// accesses have occurred. A write
// of 0 has no effect on the state
// of this bit.
//******************************************************************************
//
// The following are defines for the bit fields in the FLASH_CTRL_O_FMC2 register.
//
//******************************************************************************
#define FLASH_CTRL_FMC2_WRKEY_M 0xFFFF0000 // Flash Memory Write Key This
// field contains a write key which
// is used to minimize the incidence
// of accidental Flash memory
// writes. The value 0xA442 must be
// written into this field for a
// write to occur. Writes to the
// FMC2 register without this WRKEY
// value are ignored. A read of this
// field returns the value 0.
#define FLASH_CTRL_FMC2_WRKEY_S 16
#define FLASH_CTRL_FMC2_WRBUF 0x00000001 // Buffered Flash Memory Write This
// bit is used to start a buffered
// write to Flash memory. Value
// Description 1 Set this bit to
// write the data stored in the FWBn
// registers to the location
// specified by the contents of the
// FMA register. When read a 1
// indicates that the previous
// buffered Flash memory write
// access is not complete. 0 A write
// of 0 has no effect on the state
// of this bit. When read a 0
// indicates that the previous
// buffered Flash memory write
// access is complete.
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FWBVAL register.
//
//******************************************************************************
#define FLASH_CTRL_FWBVAL_FWBN_M \
0xFFFFFFFF // Flash Memory Write Buffer Value
// Description 1 The corresponding
// FWBn register has been updated
// since the last buffer write
// operation and is ready to be
// written to Flash memory. 0 The
// corresponding FWBn register has
// no new data to be written. Bit 0
// corresponds to FWB0 offset 0x100
// and bit 31 corresponds to FWB31
// offset 0x13C.
#define FLASH_CTRL_FWBVAL_FWBN_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the FLASH_CTRL_O_FWB1 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB1_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB1_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the FLASH_CTRL_O_FWB2 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB2_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB2_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the FLASH_CTRL_O_FWB3 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB3_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB3_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the FLASH_CTRL_O_FWB4 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB4_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB4_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the FLASH_CTRL_O_FWB5 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB5_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB5_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the FLASH_CTRL_O_FWB6 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB6_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB6_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the FLASH_CTRL_O_FWB7 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB7_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB7_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the FLASH_CTRL_O_FWB8 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB8_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB8_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the FLASH_CTRL_O_FWB9 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB9_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB9_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FWB10 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB10_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB10_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FWB11 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB11_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB11_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FWB12 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB12_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB12_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FWB13 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB13_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB13_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FWB14 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB14_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB14_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FWB15 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB15_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB15_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FWB16 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB16_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB16_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FWB17 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB17_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB17_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FWB18 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB18_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB18_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FWB19 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB19_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB19_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FWB20 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB20_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB20_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FWB21 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB21_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB21_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FWB22 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB22_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB22_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FWB23 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB23_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB23_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FWB24 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB24_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB24_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FWB25 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB25_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB25_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FWB26 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB26_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB26_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FWB27 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB27_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB27_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FWB28 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB28_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB28_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FWB29 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB29_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB29_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FWB30 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB30_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB30_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FWB31 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB31_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB31_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FWB32 register.
//
//******************************************************************************
#define FLASH_CTRL_FWB32_DATA_M 0xFFFFFFFF // Data Data to be written into the
// Flash memory.
#define FLASH_CTRL_FWB32_DATA_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_FSIZE register.
//
//******************************************************************************
#define FLASH_CTRL_FSIZE_SIZE_M 0x0000FFFF // Flash Size Indicates the size of
// the on-chip Flash memory. Value
// Description 0x0003 8 KB of Flash
// 0x0007 16 KB of Flash 0x000F 32
// KB of Flash 0x001F 64 KB of Flash
// 0x002F 96 KB of Flash 0x003F 128
// KB of Flash 0x005F 192 KB of
// Flash 0x007F 256 KB of Flash
#define FLASH_CTRL_FSIZE_SIZE_S 0
//******************************************************************************
//
// The following are defines for the bit fields in the
// FLASH_CTRL_O_SSIZE register.
//
//******************************************************************************
#define FLASH_CTRL_SSIZE_SRAM_SIZE_M \
0x0000FFFF // SRAM Size Indicates the size of
// the on-chip SRAM. Value
// Description 0x0007 2 KB of SRAM
// 0x000F 4 KB of SRAM 0x0017 6 KB
// of SRAM 0x001F 8 KB of SRAM
// 0x002F 12 KB of SRAM 0x003F 16 KB
// of SRAM 0x004F 20 KB of SRAM
// 0x005F 24 KB of SRAM 0x007F 32 KB
// of SRAM
#define FLASH_CTRL_SSIZE_SRAM_SIZE_S 0
#define FLASH_CTRL_FMC_WRKEY 0xA4420000 // FLASH write key
#define FLASH_CTRL_FMC2_WRKEY 0xA4420000 // FLASH write key
#define FLASH_CTRL_O_FWBN FLASH_CTRL_O_FWB1
#define FLASH_ERASE_SIZE 0x00000400
#define FLASH_PROTECT_SIZE 0x00000800
#define FLASH_FMP_BLOCK_0 0x00000001 // Enable for block 0
#define FLASH_FMPRE0 0x400FE200 // Flash Memory Protection Read
// Enable 0
#define FLASH_FMPRE1 0x400FE204 // Flash Memory Protection Read
// Enable 1
#define FLASH_FMPRE2 0x400FE208 // Flash Memory Protection Read
// Enable 2
#define FLASH_FMPRE3 0x400FE20C // Flash Memory Protection Read
// Enable 3
#define FLASH_FMPRE4 0x400FE210 // Flash Memory Protection Read
// Enable 4
#define FLASH_FMPRE5 0x400FE214 // Flash Memory Protection Read
// Enable 5
#define FLASH_FMPRE6 0x400FE218 // Flash Memory Protection Read
// Enable 6
#define FLASH_FMPRE7 0x400FE21C // Flash Memory Protection Read
// Enable 7
#define FLASH_FMPRE8 0x400FE220 // Flash Memory Protection Read
// Enable 8
#define FLASH_FMPRE9 0x400FE224 // Flash Memory Protection Read
// Enable 9
#define FLASH_FMPRE10 0x400FE228 // Flash Memory Protection Read
// Enable 10
#define FLASH_FMPRE11 0x400FE22C // Flash Memory Protection Read
// Enable 11
#define FLASH_FMPRE12 0x400FE230 // Flash Memory Protection Read
// Enable 12
#define FLASH_FMPRE13 0x400FE234 // Flash Memory Protection Read
// Enable 13
#define FLASH_FMPRE14 0x400FE238 // Flash Memory Protection Read
// Enable 14
#define FLASH_FMPRE15 0x400FE23C // Flash Memory Protection Read
// Enable 15
#define FLASH_FMPPE0 0x400FE400 // Flash Memory Protection Program
// Enable 0
#define FLASH_FMPPE1 0x400FE404 // Flash Memory Protection Program
// Enable 1
#define FLASH_FMPPE2 0x400FE408 // Flash Memory Protection Program
// Enable 2
#define FLASH_FMPPE3 0x400FE40C // Flash Memory Protection Program
// Enable 3
#define FLASH_FMPPE4 0x400FE410 // Flash Memory Protection Program
// Enable 4
#define FLASH_FMPPE5 0x400FE414 // Flash Memory Protection Program
// Enable 5
#define FLASH_FMPPE6 0x400FE418 // Flash Memory Protection Program
// Enable 6
#define FLASH_FMPPE7 0x400FE41C // Flash Memory Protection Program
// Enable 7
#define FLASH_FMPPE8 0x400FE420 // Flash Memory Protection Program
// Enable 8
#define FLASH_FMPPE9 0x400FE424 // Flash Memory Protection Program
// Enable 9
#define FLASH_FMPPE10 0x400FE428 // Flash Memory Protection Program
// Enable 10
#define FLASH_FMPPE11 0x400FE42C // Flash Memory Protection Program
// Enable 11
#define FLASH_FMPPE12 0x400FE430 // Flash Memory Protection Program
// Enable 12
#define FLASH_FMPPE13 0x400FE434 // Flash Memory Protection Program
// Enable 13
#define FLASH_FMPPE14 0x400FE438 // Flash Memory Protection Program
// Enable 14
#define FLASH_FMPPE15 0x400FE43C // Flash Memory Protection Program
// Enable 15
#define FLASH_USECRL 0x400FE140 // USec Reload
#define FLASH_CTRL_ERASE_SIZE 0x00000400
#endif // __HW_FLASH_CTRL_H__